What is command for turning off wifi?

Arkadiusz

Thanks, both answers worked for me M552 S-1 it was.

I'm not sure which is my duetwifiserver version:
FIRMWARE_NAME: RepRapFirmware for Duet 2 WiFi/Ethernet FIRMWARE_VERSION: 2.02(RTOS) ELECTRONICS: Duet WiFi 1.02 or later FIRMWARE_DATE: 2018-12-24b1<LF>ok<LF>

dc42

To check the DuetWiFServer version, turn the WiFi module on (idle mode will do), send M122 and look at the WiFi section of the report. If using USB/YAT then change the line terminator in YAT to LF only.

A Former User

Its covered in the wiki
https://duet3d.dozuki.com/Wiki/Gcode#Section_M552_Set_IP_address_enable_disable_network_interface

(too late, never mind, post got flagged for spam and when it went through there were more replies..)

Arkadiusz

@dc42 I tried your method but I'm still not sure what duetwifiserver version I'm running:
=== Diagnostics ===<LF>RepRapFirmware for Duet 2 WiFi/Ethernet version 2.02(RTOS) running on Duet WiFi 1.02 or later<LF>Board ID: 08DGM-917DA-G4MS8-6J9D6-3S46N-9TT7B<LF>Used output buffers: 1 of 20 (4 max)<LF>=== RTOS ===<LF>Static ram: 25524<LF>Dynamic ram: 98424 of which 0 recycled<LF>Exception stack ram used: 320<LF>Never used ram: 6804<LF>Tasks: NETWORK(ready,1260) HEAT(blocked,1232) MAIN(running,3844) IDLE(ready,200)<LF>Owned mutexes:<LF>=== Platform ===<LF>

I managed to put wifi into idle, but I have to do it every time I start machine otherwise I'm constantly getting annoying message "wifi reported error"

How can I disable wifi completely ?

Arkadiusz

@bearer

Section in link you provided is misleading, it says that S0 will disable wifi where it only puts wifi into idle:

Parameters for Duet 2 Ethernet and 06/085

Pnnn IP address, 0.0.0.0 means acquire an IP address using DHCP
Snnn 0 = disable networking, 1 = enable networking
Rnnn (optional, RepRapFirmware 1.17 and earlier only) HTTP port, default 80

I don't know what you mean with post being flagged.

A Former User

@arkadiusz said in What is command for turning off wifi?:

Section in link you provided is misleading, it says that S0 will disable wifi where it only puts wifi into idle:

Not really, if you read the section pertaining to the wifi board you'll see S-1 disables it.

I don't know what you mean with post being flagged.

Forum initially didn't allow the reply because it thought it was spam, so I tried again later and did't see it had been answered already.

Arkadiusz

You're right, I copied wrong section, I tried S-1 as suggested before but it only works at the beginning after executing command.
When duet is rebooted it goes back to idle and keep searching for wifi.

A Former User

@arkadiusz said in What is command for turning off wifi?:

I managed to put wifi into idle, but I have to do it every time I start machine otherwise I'm constantly getting annoying message "wifi reported error"
How can I disable wifi completely ?

try adding the disable command to your config.g file? (at least it will run the disable command automatically on boot).

Phaedrux

@arkadiusz said in What is command for turning off wifi?:

When duet is rebooted it goes back to idle and keep searching for wifi.

You need to edit config.g. There is probably M552 S1 in there already to start wifi at bootup. Either remove it, or change it to M552 S-1

Arkadiusz

Thanks for help everyone, I'm still beginner here and I appreciate all help provided.
Like bearer and Phaedrux said I had to modify config.g.