extruder buttons in DWC won't be gray, its grayed out



  • HI again, what I'm doing wrong, the extruder buttons in DWC won't be gray, its grayed out.

    ; Configuration file for Duet WiFi (firmware version 2.03)
    ; executed by the firmware on start-up
    ;
    ; generated by RepRapFirmware Configuration Tool v2.1.8 on Thu Feb 20 2020 13:12:07 GMT+0100 (centraleuropeisk normaltid)
    
    ; General preferences
    G90                                     ; send absolute coordinates...
    M83                                     ; ...but relative extruder moves
    M550 P"My Printer"                      ; set printer name
    
    ; Network
    M552 S1                                 ; enable network
    M586 P0 S1                              ; enable HTTP
    M586 P1 S0                              ; disable FTP
    M586 P2 S0                              ; disable Telnet
    
    ; Drives
    M569 P0 S1                              ; physical drive 0 goes forwards
    M569 P1 S1                              ; physical drive 1 goes forwards
    M569 P2 S0                              ; physical drive 2 goes backwards
    M569 P3 S0                              ; physical drive 3 goes forwards
    M584 X0 Y1 Z2 E3                        ; set drive mapping
    M350 X16 Y16 Z16 E16 I1                 ; configure microstepping with interpolation
    M92 X160.00 Y160.00 Z2560.00 E873.08    ; set steps per mm
    M566 X900.00 Y900.00 Z12.00 E120.00     ; set maximum instantaneous speed changes (mm/min)
    M203 X6000.00 Y6000.00 Z180.00 E1200.00 ; set maximum speeds (mm/min)
    M201 X400.00 Y500.00 Z20.00 E250.00     ; set accelerations (mm/s^2)
    M906 X800 Y800 Z800 E800 I30            ; set motor currents (mA) and motor idle factor in per cent
    M84 S30                                 ; Set idle timeout
    
    ; Axis Limits
    M208 X-33 Y-10 Z0 S1                    ; set axis minima
    M208 X230 Y230 Z240 S0                  ; set axis maxima
    
    ; Endstops
    M574 X1 Y1 Z1 S0                        ; set active high endstops
    
    ; Z-Probe
    M558 P0 H5 F120 T6000                   ; disable Z probe but set dive height, probe speed and travel speed
    M557 X-18:215 Y5:195 S20                ; define mesh grid
    
    ; Heaters
    M305 P0 T100000 B4138 R4700             ; set thermistor + ADC parameters for heater 0
    M143 H0 S120                            ; set temperature limit for heater 0 to 120C
    M305 P1 T100000 B4138 R4700             ; set thermistor + ADC parameters for heater 1
    M143 H1 S280                            ; set temperature limit for heater 1 to 280C
    
    ; Fans
    M106 P0 S0 I0 F500 H-1                  ; set fan 0 value, PWM signal inversion and frequency. Thermostatic control is turned off
    M106 P1 S1 I0 F500 H1 T45               ; set fan 1 value, PWM signal inversion and frequency. Thermostatic control is turned on
    
    ; Tools
    M563 P0 D0 S"TitanAero" H1 F0                        ; define tool 0
    G10 P0 X0 Y0 Z0                         ; set tool 0 axis offsets
    G10 P0 R0 S0
    M302 ; Report current state
    M302 P0 ; Allow cold extrusion
    M375 ; Load height map                            ; set initial tool 0 active and standby temperatures to 0C
    T0
    ; Custom settings are not defined
    

    Extruder.png



  • hi,

    the extrusions button wil be gray if you heat your hotend over 160 °C (is a default setting) for more Information see https://duet3d.dozuki.com/Wiki/Gcode#Section_M302_Allow_cold_extrudes



  • but is it ok configured in tools? Also has Allow cold extrusion



  • for cold extrusion you have to set M302 P1



  • Thanks! I missed, sory.


Log in to reply