New experimental firmware 1.19beta10

dc42

Lars, I found the problem: I missed a minus sign when transposing a formula from Maxima to the source code. So in the 3 leadscrews case it was computing the second leadscrew correction with the wrong sign.

Please try 1.19beta10+2 which I have just released.

DjDemonD

Heater tuning
Old version 1.18.1
M307 H0 A311.7 C649.8 D3.1 S1.00 B0
M307 H1 A423.4 C203.6 D5.1 S1.00 B0
1.19 Beta 10
M307 H0 A240.2 C387.9 D1.1 S1.00 B0
M307 H1 A469.9 C253.0 D4.8 S1.00 B0

W3DRK

Can this new independent Z motor leveling be used for dual Z Cartesian printers like the Prusa, OrdBot, clones, etc, or is this a Delta only feature? Seems like it could be used to automatically get the X-axis of the bed mechanically leveled, only requiring the Z motors to track Y-axis movement…

Yonkiman

@dc42:

Do you have a config-override.g file, and a M501 command near the end of config.g?

No. I took the post-calibration M665 and M666 numbers from config-override.g, put them in config.g, and deleted config-override.g. No M501 command at the end of config.g. (I tried the M501 / config-override.g methodology in the past but ultimately prefer to have it all in config.g).

Those numbers look good to me.

Good to hear!

lars

@dc42:

Lars, I found the problem: I missed a minus sign when transposing a formula from Maxima to the source code. So in the 3 leadscrews case it was computing the second leadscrew correction with the wrong sign.

Please try 1.19beta10+2 which I have just released.

Works now!

Yonkiman

I have another oddity to report with 1.19beta10:

Sometimes when a (successful) print ends, I get a "Can't delete file 0:/sys/resurrect.g" error. It's not surprising it can't delete it (because I don't have a resurrect.g file), but I never saw that error until recently (I'm pretty sure coincident with going from beta8 to beta10). I also don't know where the [c]G10 P1 S0[/c] came from - it's not in my gcode, and the only [c]G10[/c]s I have in my Duet config files are [c]G10 P0 R0 S0[/c] and [c]G10 P1 R0 S0[/c] in my config.g file when I set up my tools. Here's the console output from a print I ran last night:

11:12:00 PM	G10 P1 S0
		Can't delete file 0:/sys/resurrect.g
		Done printing file
11:11:56 PM	Can't delete file 0:/sys/resurrect.g
		Done printing file

Here are the last lines of gcode from that print:```
G1 X0.053 Y9.146 F540
G1 E-8.0000 F6000
; layer end
T0 ; Select Extruder 0 if not already selected
G90 ; Switch to absolute mode
G1 X0 Y0 Z250 E-10 F6000 ; Retract filament and raise printhead
M104 S0 ; Turn off heater
M84 S10 ; turn off motors after 10 seconds

BTW, do you prefer feedback like this in this forum or as an issue in github?

dc42

Thanks, Yonkiman. I prefer issues reported here, especially for betas.

Regarding G1 P1 S0, do you have a stop.g file, and if so, is it in that?

I'll suppress the "Can't delete" message in the next beta.

dc42

Chrishamm has released DWC 1.17+2 which includes the changes needed to work with the new height map. So will those of you running firmware 1.19beta10 please upgrade it to 1.19beta10+2 if you haven't already, and upgrade DWC to 1.17+2. The mesh bed compensation height map should then display correctly.

Yonkiman

@dc42:

Regarding G1 P1 S0, do you have a stop.g file, and if so, is it in that

Yes, I have the file; no it is not in that file. File only has the default 2 comment lines. I actually did a search for the word "G10" on my entire SD card, and it only appeared in the tool setup in config.g (as reported above) and one or two binary files.

Speaking of which…once we successfully flash the firmware, is it safe to remove all the non-text (i.e. .bin/.zip/.rar) files from our sys directory?

dc42

@Yonkiman:

Speaking of which…once we successfully flash the firmware, is it safe to remove all the non-text (i.e. .bin/.zip/.rar) files from our sys directory?

Yes, although the only binary files that should be in there are the two extra .bin files for the Duet WiFi.

W3DRK

Hey David, did you see my question nested up a few posts about dual-Z motor cartesian printers?

dc42

@W3DRK:

Can this new independent Z motor leveling be used for dual Z Cartesian printers like the Prusa, OrdBot, clones, etc, or is this a Delta only feature? Seems like it could be used to automatically get the X-axis of the bed mechanically leveled, only requiring the Z motors to track Y-axis movement…

Yes, it's for Cartesian and CoreXY printers, not deltas.. See https://duet3d.com/wiki/Bed_levelling_using_multiple_independent_Z_motors.

It can also be used to tell you what adjustments to make to manual bed levelling screws, but I haven't documented how to do that yet.

lars

Did some more testing for the leveling. There might be some other bug. Feels like its still adjusting in the wrong direction…
I changed the probe order to match the reporting of G32 and moved the points a bit.

16:55:14 M98 P0:/macros/4 - Leveling Check Probe
Bed probe heights: -0.136 -0.441 -0.471, mean -0.349, deviation from mean 0.151
16:54:26 G32
Error: some computed corrections exceed configured limit of 0.50mm: -0.007 0.505 0.553
16:52:50 M98 P0:/macros/4 - Leveling Check Probe
Bed probe heights: -0.138 -0.439 -0.461, mean -0.346, deviation from mean 0.147
16:52:09 G32
Leadscrew adjustments made: -0.294 0.260 0.269, points used 3, deviation before 0.170 after 0.000
16:51:36 M98 P0:/macros/4 - Leveling Check Probe
Bed probe heights: 0.186 -0.203 -0.174, mean -0.064, deviation from mean 0.177

Front left lead screw (-60,-10) is connected to Z (drive 2)
Front right lead screw (560,-10) is connected to Y (drive 1)
Back centre lead screw (250,560) is connected to X (Drive 0)

Macro "4 - Leveling Check Probe":

T0
M401
G30 P0 X250 Y420 Z-99999    ; probe near a leadscrew
G30 P1 X420 Y80 Z-99999     ; probe near a leadscrew and calibrate 3 motors
G30 P2 X80 Y80 Z-99999 S-1  ; probe near a leadscrew
M402
G90
G1 X250 Y250
T-1

```bed.g:

T0
M401
G30 P0 X250 Y420 Z-99999 ; probe near a leadscrew
G30 P1 X420 Y80 Z-99999 ; probe near a leadscrew and calibrate 3 motors
G30 P2 X80 Y80 Z-99999 S3 ; probe near a leadscrew
M402
G90
G1 Y250
T-1

M584 Y5 X7 U8 V6 E3:4 Z0:1:2 ; Set up steppers for x, y, u, v, z and e, use P4 once it works to hide V
M671 X250:560:-60 Y560:-10:-10 S0.5 ; Set up lead screw positions for bed leveling

dc42

Lars, thanks for that. The corrections it wants to make now look correct - they are similar to the height errors but with opposite sign and somewhat larger magnitude - which is expected because you are probing well inside the leadscrew positions.

As you say, it looks like the corrections may be getting applied with the wrong sign, at least for the 2nd and 3rd screws. I'll simulate your figures on my Cartesian printer (which has only 1 Z motor) and see whether there is a problem with positive corrections.

EDIT: I found the problem. When it is setting the motor direction, it sets the directions of all Z motors together instead of individually. I will fix this shortly as I am keen to get this feature working properly.

dc42

Lars, please try DuetWiFiFirmware 1.19beta10+3, available here https://dl.dropboxusercontent.com/u/19369680/DuetWiFiFirmware.bin.

lars

21:45:43 M98 P0:/macros/4 - Leveling Check Probe
Bed probe heights: -0.275 -0.663 0.068, mean -0.290, deviation from mean 0.299
21:45:15 G32
Error: some computed corrections exceed configured limit of 0.50mm: 0.260 0.969 -0.344
21:44:34 M98 P0:/macros/4 - Leveling Check Probe
Bed probe heights: -0.274 -0.659 0.049, mean -0.295, deviation from mean 0.289
21:43:43 G32
Leadscrew adjustments made: 0.136 0.486 -0.174, points used 3, deviation before 0.210 after 0.000
21:42:42 M98 P0:/macros/4 - Leveling Check Probe
Bed probe heights: -0.148 -0.339 0.041, mean -0.149, deviation from mean 0.155
21:41:57 G32
Leadscrew adjustments made: 0.043 0.230 -0.082, points used 3, deviation before 0.094 after 0.000
21:41:19 M98 P0:/macros/4 - Leveling Check Probe
Bed probe heights: -0.010 -0.112 0.054, mean -0.023, deviation from mean 0.069

Firmware Name: RepRapFirmware for Duet WiFi
Firmware Electronics: Duet WiFi 1.0 + DueX5
Firmware Version: 1.19beta10+3 (2017-07-21)
WiFi Server Version: 1.19beta9
Web Interface Version: 1.17+2

Yonkiman

Just in case they got lost in all the back-and forth, here are the two issues I'm still seeing with 1.19beta10+2 & DWC 1.17+2:

M666 in config.g doesn't execute/"stick" - after a reboot M666 is always reset to [c]Endstop adjustments X0.00 Y0.00 Z0.00, tilt X0.00% Y0.00%[/c]. I don't have a config-override.g file or an M501 command in my config.g. M665 in config.g works as expected.
My prints are now ending with a "Can't delete file 0:/sys/resurrect.g" error, and the final lines in my gcode are not executed:

G1 X0.053 Y9.146 F540
G1 E-8.0000 F6000
; layer end
T0		; Select Extruder 0 if not already selected
G90		; Switch to absolute mode
G1 X0 Y0 Z250 E-10  F6000	; Retract filament and raise printhead
M104 S0		; Turn off heater
M84 S10		; turn off motors after 10 seconds

```I'm guessing it might have to do with the [c]T0[/c], because the print completes, but the printhead doesn't move up and the heater doesn't turn off. I'll try a print without the [c]T0[/c] tomorrow and see if the problem goes away.

lars

David, any chance you could add the probe point data in the output together with the adjustment for the leveling?

dc42

@lars:

21:45:43 M98 P0:/macros/4 - Leveling Check Probe
Bed probe heights: -0.275 -0.663 0.068, mean -0.290, deviation from mean 0.299
21:45:15 G32
Error: some computed corrections exceed configured limit of 0.50mm: 0.260 0.969 -0.344
21:44:34 M98 P0:/macros/4 - Leveling Check Probe
Bed probe heights: -0.274 -0.659 0.049, mean -0.295, deviation from mean 0.289
21:43:43 G32
Leadscrew adjustments made: 0.136 0.486 -0.174, points used 3, deviation before 0.210 after 0.000
21:42:42 M98 P0:/macros/4 - Leveling Check Probe
Bed probe heights: -0.148 -0.339 0.041, mean -0.149, deviation from mean 0.155
21:41:57 G32
Leadscrew adjustments made: 0.043 0.230 -0.082, points used 3, deviation before 0.094 after 0.000
21:41:19 M98 P0:/macros/4 - Leveling Check Probe
Bed probe heights: -0.010 -0.112 0.054, mean -0.023, deviation from mean 0.069

Firmware Name: RepRapFirmware for Duet WiFi
Firmware Electronics: Duet WiFi 1.0 + DueX5
Firmware Version: 1.19beta10+3 (2017-07-21)
WiFi Server Version: 1.19beta9
Web Interface Version: 1.17+2

This is strange. I set up my bench system, configured as a CoreXY with your leadscrew positions and motor assignments:

M584 Y5 X7 U8 V6 E3:4 Z0:1:2         ; Set up steppers for x, y, u, v, z and e, use P4 once it works to hide V
M671 X250:560:-60 Y560:-10:-10 S0.5  ; Set up lead screw positions for bed leveling

I created a bed.g file like yours, except that I put the initial probe height errors that you reported in it:

G30 P0 X250 Y420 Z-0.010  
G30 P1 X420 Y80 Z-0.112    
G30 P2 X80 Y80 Z0.054 S3

I set my Z steps/mm to 3200 so that 1mm movement is 1 revolution of the motor. I have flags on the motor shafts so that I can see the movement. I loaded firmware 1.19beta10+3. I sent G92 X0 Y0 Z10 as I don't have any means of homing this setup.

When I run G31, I get this:

Leadscrew adjustments made: 0.002 0.185 -0.117, points used 3, deviation before 0.072 after 0.000

I can see the X motor moving clockwise very slightly, the Y motor moving clockwise a little less than 1/5 of a turn, and the Z motor moving anticlockwise a little less than 1/8 of a turn. I checked that when I command +Z movement, the rotation is clockwise. So it all looks correct.

Please can you check a few things:

1. Is the maximum Z speed in your M201 command in config.g achievable?

2. Are you certain that you have the motors connected to the driver outputs in the order listed? Bear in mind that the order of driver outputs along the edge of the Duet is 2 1 0 3 4 (i.e. Z Y X E0 E1) not 0 1 2 3 4.

3. Can you see the leadscrews moving by about the correct amount, in the correct direction?

dc42

@Yonkiman:

Just in case they got lost in all the back-and forth, here are the two issues I'm still seeing with 1.19beta10+2 & DWC 1.17+2:

M666 in config.g doesn't execute/"stick" - after a reboot M666 is always reset to [c]Endstop adjustments X0.00 Y0.00 Z0.00, tilt X0.00% Y0.00%[/c]. I don't have a config-override.g file or an M501 command in my config.g. M665 in config.g works as expected.

My prints are now ending with a "Can't delete file 0:/sys/resurrect.g" error, and the final lines in my gcode are not executed:
G1 X0.053 Y9.146 F540
G1 E-8.0000 F6000
; layer end
T0		; Select Extruder 0 if not already selected
G90		; Switch to absolute mode
G1 X0 Y0 Z250 E-10  F6000	; Retract filament and raise printhead
M104 S0		; Turn off heater
M84 S10		; turn off motors after 10 seconds

```I'm guessing it might have to do with the [c]T0[/c], because the print completes, but the printhead doesn't move up and the heater doesn't turn off. I'll try a print without the [c]T0[/c] tomorrow and see if the problem goes away.

Thanks for your report.

I can't reproduce the M666 problem, it works on my delta. Please share your config.g file. If you run M98 Pconfig.g subsequently, does it pick up the correct M666 settings?

I don't know why the last few lines of gcode are not being executed. Is tool 0 active at the end, or is some other tool active? Do you have anything in the tool change files for tool 0?

The "Can't delete" message will be fixed in the next beta.