Duet2 WiFi Firmware on Raise 3d E2 ?

Veti

if the thread is m3 you might be able to use these as replacement

https://de.aliexpress.com/item/1005002022267605.html

Proschi3D

The Gcodes have also been changed

https://github.com/Raise3D/Reprap-Raise3D-E2-Series/blob/master/RepRapFirmware/src/GCodes/GCodes3.cpp#L1

Proschi3D

I will try to create a firmware that consists of a duet and raise mix

Proschi3D

what does the number after Recv : ok (20) Mean?

Phaedrux

Where are you seeing that message?

Proschi3D

@Phaedrux In the log of printing

Veti

is that in octoprint?

Proschi3D

@Veti No, it is in the printer's log.

Phaedrux

Screen shot?

Proschi3D

@Phaedrux

Phaedrux

I think you're outside the realm of what we can help you with here. I'm not familiar with the Raise3D printer or what it's doing.

Proschi3D

@Phaedrux I think the bufer is full right? Where would it be enlarged with a duet wifi?

Veti

they are acknowledgement of g code received.

so something is sending g code to the duet.

Proschi3D

@Veti Yes, the display board sends the gcode to the motion board

Veti

you will have to figure that one out yourself.

also can you post the result of M122

Proschi3D

(>>) === Diagnostics ===<LF>RepRapFirmware for Duet 2 WiFi/Ethernet version 2.02(RTOS) running on Duet WiFi 1.02 or later<LF>Board ID: 08DLM-996RU-N8PS4-7J1D8-3SJ6N-1B9BR<LF>Used output buffers: 1 of 20 (1 max)<LF>=== RTOS ===<LF>Static ram: 25536<LF>Dynamic ram: 99000 of which 0 recycled<LF>Exception stack ram used: 256<LF>Never used ram: 6280<LF>Tasks: HEAT(blocked,1232) MAIN(running,3828) IDLE(ready,200)<LF>Owned mutexes:<LF>=== Platform ===<LF>Last reset 00:00:40 ago, cause: power up<LF>Last software reset time unknown, reason: User, spinning module GCodes, available RAM 6224 bytes (slot 0)<LF>Software reset code 0x0003 HFSR 0x00000000 CFSR 0x00000000 ICSR 0x0441f000 BFAR 0xe000ed38 SP 0xffffffff Task 0x4e49414d<LF>Error status: 0<LF>Free file entries: 10<LF>SD card 0 detected, interface speed: 20.0MBytes/sec<LF>SD card longest block write time: 0.0ms, max retries 0<LF>MCU temperature: min 18.7, current 23.2, max 23.4<LF>Supply voltage: min 0.0, current 0.6, max 0.9, under voltage events: 0, over voltage events: 0, power good: no<LF>Driver 0: ok, SG[Warning: Maximal number of bytes per line exceeded! Check the EOL (end-of-line) settings or increase the limit in the advanced terminal settings.]

Veti

please change the EOL settings so that the entire settings are printed

Phaedrux

Proschi3D

(>>) === Diagnostics === (0.000)
(>>) RepRapFirmware for Duet 2 WiFi/Ethernet version 2.02(RTOS) running on Duet WiFi 1.02 or later (0.000)
(>>) Board ID: 08DGM-9T6BU-FG3SS-6J9FD-3S46R-TVSHD (0.000)
(>>) Used output buffers: 1 of 20 (3 max) (0.000)
(>>) === RTOS === (0.000)
(>>) Static ram: 25536 (0.000)
(>>) Dynamic ram: 99012 of which 0 recycled (0.000)
(>>) Exception stack ram used: 448 (0.000)
(>>) Never used ram: 6076 (0.000)
(>>) Tasks: HEAT(blocked,1216) MAIN(running,3772) IDLE(ready,200) (0.000)
(>>) Owned mutexes: (0.000)
(>>) === Platform === (0.000)
(>>) Last reset 00:03:38 ago, cause: power up (0.000)
(>>) Last software reset time unknown, reason: User, spinning module GCodes, available RAM 6212 bytes (slot 3) (0.000)
(>>) Software reset code 0x0003 HFSR 0x00000000 CFSR 0x00000000 ICSR 0x0441f000 BFAR 0xe000ed38 SP 0xffffffff Task 0x4e49414d (0.000)
(>>) Error status: 0 (0.000)
(>>) Free file entries: 10 (0.000)
(>>) SD card 0 detected, interface speed: 20.0MBytes/sec (0.000)
(>>) SD card longest block write time: 5.0ms, max retries 0 (0.000)
(>>) MCU temperature: min 26.8, current 32.7, max 33.0 (0.000)
(>>) Supply voltage: min 23.8, current 24.0, max 24.2, under voltage events: 0, over voltage events: 0, power good: yes (0.000)
(>>) Driver 0: standstill, SG min/max 0/348 (0.000)
(>>) Driver 1: standstill, SG min/max 0/139 (0.000)
(>>) Driver 2: standstill, SG min/max 16/358 (0.000)
(>>) Driver 3: standstill, SG min/max not available (0.000)
(>>) Driver 4: standstill, SG min/max not available (0.000)
(>>) Driver 5: standstill, SG min/max not available (0.000)
(>>) Date/time: 1970-01-01 00:00:00 (0.000)
(>>) Cache data hit count 413358567 (0.000)
(>>) Slowest loop: 10.00ms; fastest: 0.08ms (0.000)
(>>) I2C nak errors 0, send timeouts 0, receive timeouts 0, finishTimeouts 0 (0.000)
(>>) === Move === (0.000)
(>>) Hiccups: 293, StepErrors: 0, LaErrors: 0, FreeDm: 240, MinFreeDm: 237, MaxWait: 129054ms, Underruns: 0, 0 (0.000)
(>>) Scheduled moves: 12, completed moves: 12 (0.000)
(>>) Bed compensation in use: none (0.000)
(>>) Bed probe heights: 0.000 0.000 0.000 0.000 0.000 (0.000)
(>>) === Heat === (0.000)
(>>) Bed heaters = 0 -1 -1 -1, chamberHeaters = -1 -1 (0.000)
(>>) Heater 1 is on, I-accum = 0.0 (0.000)
(>>) === GCodes === (0.000)
(>>) Segments left: 0 (0.000)
(>>) Stack records: 2 allocated, 0 in use (0.000)
(>>) Movement lock held by null (0.000)
(>>) http is idle in state(s) 0 (0.000)
(>>) telnet is idle in state(s) 0 (0.000)
(>>) file is idle in state(s) 0 (0.000)
(>>) serial is ready with "M122" in state(s) 0 (0.000)
(>>) aux is idle in state(s) 0 (0.000)
(>>) daemon is idle in state(s) 0 (0.000)
(>>) queue is idle in state(s) 0 (0.000)
(>>) autopause is idle in state(s) 0 (0.000)
(>>) Code queue is empty. (0.000)
(>>) === Network === (0.000)
(>>) Slowest loop: 0.00ms; fastest: 4581298.50ms (0.000)
(>>) Responder states: HTTP(0) HTTP(0) HTTP(0) HTTP(0) FTP(0) Telnet(0) Telnet(0) (0.000)
(>>) HTTP sessions: 0 of 8 (0.000)
(>>) - WiFi - (0.000)
(>>) Network state is disabled (0.000)
(>>) WiFi module is disabled (0.000)
(>>) Failed messages: pending 2779096485, notready 2779096485, noresp 2779096485 (0.000)
(>>) Socket states: 0 0 0 0 0 0 0 0 (0.000)
(>>) === Filament sensors === (0.000)
(>>) Extruder 0 sensor: ok (0.000)
(>>) Extruder 1 sensor: ok (0.000)