Error Parsing Response



  • Just uploaded to 3.3 beta 1 and as this is a new setup I’m not sure if that is related to my issue or not. I am getting a parsing error during printing as shown from my picture, it is constant.22C0887B-CE29-4626-A3D9-48D06E80D6BE.jpeg


  • Moderator

    If it's a new printer setup, might want to stick to the latest stable release?

    https://github.com/Duet3D/RepRapFirmware/releases/download/3.2.2/Duet2and3Firmware-3.2.2.zip

    If you want to stick with 3.3 beta 1, please post your config.g and the results of M122 and M98 P"config.g"


  • administrators

    Which version of PanelDue firmware are you using?



  • I am using PanelDue 3.2.9


  • administrators

    Are you running the Duet in standalone mode, or with an attached SBC? I am fairly sure that messages doesn't come from RepRapFirmware, so I think it must come from PanelDue or from DSF.



  • I am running it in stand alone mode.


  • Moderator

    @taylo708 This message generated whenever the status-updates from RRF cannot be parsed correctly. Can you confirm that this is new with RRF 3.3beta1 and you did not have this issue before?

    If so, please post your config.g so I can investigate the issue.



  • I was running 3.3 beta1. I also have a 3.3 beta I’m not sure if they are different or not. I went back to 3.3 beta and am still getting the same parsing error.


  • Moderator

    @taylo708 Please provide the following information:
    Output of
    M115 and M122 as well as your config.g.



  • This post is deleted!


  • m115
    FIRMWARE_NAME: RepRapFirmware for Duet 3 MB6HC FIRMWARE_VERSION: 3.3beta ELECTRONICS: Duet 3 MB6HC v1.01 or later FIRMWARE_DATE: 2021-01-20 16:37:22
    
    m122
    === Diagnostics ===
    RepRapFirmware for Duet 3 MB6HC version 3.3beta running on Duet 3 MB6HC v1.01 or later (standalone mode)
    Board ID: 08DJM-956BA-NA3TJ-6JTD0-3S06T-1V86T
    Used output buffers: 1 of 40 (23 max)
    === RTOS ===
    Static ram: 149784
    Dynamic ram: 90596 of which 24 recycled
    Never used RAM 110268, free system stack 178 words
    Tasks: NETWORK(ready,222) ETHERNET(blocked,117) HEAT(blocked,280) CanReceiv(blocked,887) CanSender(blocked,365) CanClock(blocked,326) TMC(blocked,49) MAIN(running,1120) IDLE(ready,20)
    Owned mutexes:
    === Platform ===
    Last reset 01:49:39 ago, cause: software
    Last software reset at 2021-02-22 17:03, reason: User, GCodes spinning, available RAM 110268, slot 2
    Software reset code 0x0003 HFSR 0x00000000 CFSR 0x00000000 ICSR 0x0044a000 BFAR 0x00000000 SP 0x00000000 Task MAIN Freestk 0 n/a
    Error status: 0x00
    Aux0 errors 0,0,0
    Aux1 errors 0,0,0
    MCU temperature: min 45.4, current 45.6, max 46.0
    Supply voltage: min 24.2, current 24.2, max 24.3, under voltage events: 0, over voltage events: 0, power good: yes
    12V rail voltage: min 12.0, current 12.1, max 12.2, under voltage events: 0
    Driver 0: position 0, standstill, reads 63181, writes 0 timeouts 0, SG min/max not available
    Driver 1: position 0, standstill, reads 63181, writes 0 timeouts 0, SG min/max not available
    Driver 2: position 0, standstill, reads 63182, writes 0 timeouts 0, SG min/max not available
    Driver 3: position 0, standstill, reads 63182, writes 0 timeouts 0, SG min/max not available
    Driver 4: position 0, standstill, reads 63182, writes 0 timeouts 0, SG min/max not available
    Driver 5: position 0, standstill, reads 63181, writes 0 timeouts 0, SG min/max not available
    Date/time: 2021-02-22 18:52:55
    Slowest loop: 25.59ms; fastest: 0.05ms
    === Storage ===
    Free file entries: 10
    SD card 0 detected, interface speed: 25.0MBytes/sec
    SD card longest read time 2.3ms, write time 3.3ms, max retries 0
    === Move ===
    DMs created 125, maxWait 0ms, bed compensation in use: none, comp offset 0.000
    === MainDDARing ===
    Scheduled moves 0, completed moves 0, hiccups 0, stepErrors 0, LaErrors 0, Underruns [0, 0, 0], CDDA state -1
    === AuxDDARing ===
    Scheduled moves 0, completed moves 0, hiccups 0, stepErrors 0, LaErrors 0, Underruns [0, 0, 0], CDDA state -1
    === Heat ===
    Bed heaters = 0 -1 -1 -1 -1 -1 -1 -1 -1 -1 -1 -1, chamberHeaters = 2 -1 -1 -1
    === GCodes ===
    Segments left: 0
    Movement lock held by null
    HTTP is idle in state(s) 0
    Telnet is idle in state(s) 0
    File is idle in state(s) 0
    USB is idle in state(s) 0
    Aux is idle in state(s) 0
    Trigger is idle in state(s) 0
    Queue is idle in state(s) 0
    LCD is idle in state(s) 0
    SBC is idle in state(s) 0
    Daemon is idle in state(s) 0
    Aux2 is idle in state(s) 0
    Autopause is idle in state(s) 0
    Code queue is empty.
    === CAN ===
    Messages queued 2044, send timeouts 0, received 2092, lost 0, longest wait 4ms for reply type 6024, peak Tx sync delay 147, free buffers 48 (min 47)
    === Network ===
    Slowest loop: 26.25ms; fastest: 0.02ms
    Responder states: HTTP(0) HTTP(0) HTTP(0) HTTP(0) HTTP(0) HTTP(0) FTP(0) Telnet(0), 0 sessions Telnet(0), 0 sessions
    HTTP sessions: 1 of 8
    - Ethernet -
    State: active
    Error counts: 0 0 1 0 0
    Socket states: 5 2 2 2 2 0 0 0```
    
    
    ; Configuration file for Duet 3 (firmware version 3)
    ; executed by the firmware on start-up
    ;
    ; generated by RepRapFirmware Configuration Tool v3.2.1 on Wed Jan 13 2021 13:45:55 GMT-0500 (Eastern Standard Time)
    
    ; General preferences
    G90                                           ; send absolute coordinates...
    M83                                           ; ...but relative extruder moves
    M550 P"DATA DRIVEN PERFORMANCE"               ; set printer name
    
    ; Network
    M552 S1 192.168.254.57                                  ; Enable network
    G4 S5
    ; Drives
    M569 P40.0 R0 S0 T6:6:6:0                   ; physical drive 40 goes forwards
    M569 P41.0 R0 S1 T6:6:6:0                   ; physical drive 41 goes forwards
    M569 P42.0 R0 S0 T6:6:6:0                   ; physical drive 42 goes forwards
    M569 P0.0 S1                                   ; physical drive 20 goes forwards
    M584 X40.0 Y41.0 Z42.0 E0.0                 ; set drive mapping
    M350 E16 I0                                 ; configure microstepping with interpolation
    M92  X266.666 Y266.666 Z640.00 E130.00      ; set steps per mm
    M350 E32
    M566 X300.00 Y300.00 Z20.00 E30.00        ; set maximum Jerk (mm/min)
    M203 X7000.00 Y7000.00 Z1000.00 E3000.00   ; set maximum speeds (mm/min)
    M201 X500.00 Y500.00 Z200 E2500             ; set accelerations (mm/s^2)                              
    M906 E750 I30                               ; set motor currents (mA)
    M84 S30                                     ; Disable motor idle current reduction
    
    ; Axis Limits
    M208 X0 Y0 Z0 S1                              ; set axis minima
    M208 X600 Y600 Z600 S0                        ; set axis maxima
    
    ; Endstops
    M574 X1 S1 P"!20.io2.in"                      ; configure active-high endstop for low end on X via pin 124.io2.in
    M574 Y1 S1 P"!io3.in"                         ; configure active-high endstop for low end on Y via pin io3.in
    M574 Z1 S2                                    ; configure Z-probe endstop for low end on Z
    
    ; Z-Probe
    M950 S0 C"20.io0.out"                        ; create servo pin 0 for BLTouch
    M558 P9 C"^20.io0.in" H2 F120 T600          ; set Z probe type to bltouch and the dive height + speeds
    G31 P500 X30 Y90 Z2                          ; set Z probe trigger value, offset and trigger height
    M557 X30:570 Y90:510 S28.5                     ; define mesh grid
    
    ; Heaters
    M308 S0 P"temp0" Y"thermistor" T100000 B3500 ; configure sensor 0 as thermistor on pin temp1
    M950 H0 C"out0" T0                           ; create bed heater output on out0 and map it to sensor 0
    M307 H0 R0.086 C1484.1 D36.00 B0 S1.00       ; disable bang-bang mode for the bed heater and set PWM limit
    M570 H0 T40
    M140 H0                                      ; map heated bed to heater 0
    M143 H0 S120                                 ; set temperature limit for heater 0 to 120C
    M308 S1 P"spi.cs0" Y"thermocouple-max31856" "K"   ; configure sensor 1 as thermocouple via CS pin spi.cs0
    M950 H1 C"out1" T1                           ; create nozzle heater output on 124.out0 and map it to sensor 1
    M307 H1 R2.808 C254.0 D9.08 B0 S1.00                             ; disable bang-bang mode for heater  and set PWM limit
    M143 H1 S350                                 ; set temperature limit for heater 1 to 350C
    M308 S2 P"temp1" Y"thermistor" T100000 B3500; configure sensor 2 as thermistor on pin temp0
    M950 H2 C"io1.out" T2                        ; create chamber heater output on out1 and map it to sensor 2
    M307 H2 A11 C99000 D2000 B1 S1.00                ; enable bang-bang mode for the chamber heater and set PWM limit
    M141 H2                                      ; map chamber to heater 2
    M143 H2 S70                                  ; set temperature limit for heater 2 to 70C
    
    
    ; Fans
    M950 F0 C"20.out1" Q500                      ; create fan 0 on pin 20.out1 and set its frequency
    M106 P0 S0 H-1                                  ; set fan 0 value. Thermostatic control is turned on
    
    ; Tools
    M563 P0 D0 H1 F0                             ; define tool 0
    G10 P0 X-30 Y0 Z0                               ; set tool 0 axis offsets
    G10 P0 R0 S0                                  ; set initial tool 0 active and standby temperatures to 0C
    
    ; Custom settings are not defined
    
    ; Miscellaneous
    M575 P1 S1 B57600                             ; enable support for PanelDue
    
    
    

Log in to reply