Complete download needed for new installation… confused!

1d1

Progress?
This what Pronterface tells me:
SENDING:M997 SO:1
Trying to connect at 460800 baud:
success
Erasing 244400 bytes…
Uploading file...
5% complete
10% complete
15% complete
20% complete
25% complete
30% complete
35% complete
40% complete
45% complete
50% complete
55% complete
60% complete
65% complete
70% complete
75% complete
80% complete
85% complete
90% complete
95% complete
Upload successful
[ERROR] Can't read from printer (disconnected?) (SerialException): call to ClearCommError failed
[ERROR] Can't write to printer (disconnected?) (SerialException): WriteFile failed

dc42

That's normal. It's uploaded the WiFi firmware successfully and then closes the USB port while it upgraded the main firmware. Assuming you left it.powered up for a minute or so to complete the upgrade, you should be able to reconnect.

1d1

OK. I have redone it all and those files are installed, Pronterface is connected and the SDHC card is mounted.
I remain lost past that.
Where should I install RepRap Firmware 1.19? Were all files that exist on the SD card uploaded, i.e., /www folder and /macro folder? And I'm still nowhere with Duet Web Control.
I'm dense with ignorance and you must be shaking your head dealing with a NOOB such as I. I don't know why this is so difficult for me - I've managed to blunder my way through Arduino (for RAMPS), Smoothieboard setups and a couple of others along the way, but this is somehow wicked confusing to me.
I truly appreciate your time and efforts on my behalf!

Dean

dc42

When you send M115, what firmware version does it report? If it reports version 1.19, that's good. What you need to do next is send M552 S1 to enable WiFi networking.

1d1

This is the message: FIRMWARE_VERSION: 1.19 ELECTRONICS: Duet WiFi 1.0 FIRMWARE_DATE: 2017-08-14
ok T B:2000.0 /0.0

M552 S1
SENDING:M552 S1
WiFi module started
WiFi reported error: no known networks found

So, when configuring, do I use 192.168.1.1 and "preprap"? Or my own router?

dc42

So you need to use M587 to tell it what SSID to connect to and what password to use. Doing this from Pronterface won't work because any lowercase characters in your password will be converted to uppercase. You can either use a terminal emulator instead (I use YAT under Windows), or set up a macro file to do it as described in the instructions for upgrading to firmware 1.19.

1d1

So close!
This from the duet web control all connected and working:
Firmware Name: RepRapFirmware for Duet WiFi
Firmware Electronics: Duet WiFi 1.0
Firmware Version: 1.19 (2017-08-14)
WiFi Server Version: 1.19
Web Interface Version: 1.19

I cannot find config.g to modify for auto connect. I have sent motion and homing macros with appropriate settings. Tried to do necessary 1.19 updates and those look good, but why no config.g? Should upload RepRap firmware 1.19? still no machine movement or anything, but probably need to activate tools?

So far, one step per message. As ever, thank you!

dc42

You are already running RepRapFirmware 1.19. Go to the Settings page of Duet Web Control, then the System Files Editor tab, there you will find the config.g file and you can edit it. If for any reason isn't there, go to https://configurator.reprapfirmware.org to generate a new one. You can upload just config.g or the whole zip file generated by configtool through the Settings General tab of Duet Web Control.

1d1

Finally. Although I've yet to print (having motion and homing difficulties) I can interact with the machine with consistency on both WiFi and PanelDue. I've got heat everywhere I need it and the extruder is working accurately from my previous steps/mm config. I release you to roam freely in new vistas and stop coddling me through my incompetencies.
Thank you very much, David. The Duet seems great and I have no doubt I will get it figured out sometime this week. It is better for me to struggle a while right now so I can learn it more effectively.

Cheers,
Dean

specavia

Good day . please tell me .I accidentally pressed the ERASE button and flew all the firmware reading on the website I realized that you need to install Bossa . I installed it but do not understand which files and where to download please tell me .DuetWiFi

specavia

Good day . please tell me .I accidentally pressed the ERASE button and flew all the firmware reading on the website I realized that you need to install Bossa . I installed it but do not understand which files and where to download please tell me

dc42

All you need to know should be at https://duet3d.com/wiki/Updating_main_firmware#Fallback_procedure_.233. If there is anything there that you don't understand, feel free to ask again.

specavia

Good day . The link you advised . I did SC was listed on the page of the link . but that does not work out . can you write the process how to do it and what firmware need and do I need a flash drive for flashing process.

dc42

I have written the process, it's on the page I linked to. What didn't work for you? What do you mean by "SC" ?

You don't need a flash drive to install new firmware, you need either the SAM-BA program or the Bossa program in your PC as described on that page, and a USB cable between your PC and the Duet.

specavia

I use the Bossa program is ran the program and connected the DUET cost WIFI downloaded DuetWiFiFirmware.bin and did as said If you can't run SAM-BA (e.g. because you want to update the firmware with a Mac), you can also use Bossa 1.18 (not earlier versions) with https://github.com/shumatech/BOSSA/releases Interactive version (Bossa) does not work on high resolution screens, but you can still use the command line version (bossac). If you use the interactive version, you need to select to Wipe everything, Lock, and Boot from the Flash before pressing the Write key. If you are using the command line, try this command line: After that I pressed reset and no result

dc42

Did Bossa or bossac report "Verify successful"?

specavia

Yes exactly . report from Bossa was . now that's just . filled it with firmware 1.18 . uploaded it has disabled the usb wire put the flash drive with my settings and the result has not changed . diag lamp continues to burn

dc42

Ignore the diag lamp, whether it will be on or off depends on your Z probe configuration.

After programming, if you reset the board then the Bossa port will disappear from your mac but the Duet 3D port should appear.

specavia

tried all the firmware or what does not work . help what to do ?

specavia

3D-port of the Duo and not appearing Bossa program port too