Filament monitor using HC-020K encoder

[paboman]

Installed the firmware 1.21RC5+ (2018-03-17 build 1) apparently nothing has changed.
Still [c]M591 D0
Pulse-type filament monitor on endstop input 3, sensitivity 1.00mm/pulse, check every 3.0mm, tolerance 50.0%, no data received[/c]
https://youtu.be/nitZGkwWn7s

Maybe something wrong with my conf.g ?

[dc42]

Did you get that report after the wheel had spun a few times and the LED flashed off and on?

[paboman]

yes, after 30 min of printing the report is the same

[dc42]

I've rewritten the pulsed filament monitor support based on the code for the rotating magnet sensor, which is know to be working. Also I have changed the configuration parameters to be the same as for the rotating magnet sensor. You are welcome to try it (it's at https://www.dropbox.com/s/iq9pzfaugyfei7x/Duet2CombinedFirmware.bin?dl=0)), but as I haven't had time to test it yet I don't expect it to work.

[paboman]

I have just upgraded the firmware, should I change something in my config.g ?
Right now i have :
[c]; Filament Monitor HC-020K
M591 D0 P7 C3 S1 R70:130 L24.8 E3.0 ; Duet3D rotating magnet sensor for extruder drive 0 is connected to E0 endstop input, 7 = pulse-generating, sensorsensitivity 24.8mm.rev, 50% to 130% tolerance, 3mm detection length
M591 D0 ; display filament sensor parameters for extruder drive 0[/c]

[paboman]

now after the prints begins i get : [c]Extruder 0 reports too little movement[/c]

[paboman]

Upgraded to:
1.21RC5+ (2018-03-17 build 2)

I have changed my settings in config.g to:

[c]; Filament Monitor HC-020K
M591 D0 P7 S23.5 C3 R50 E3.0 ; Duet3d sensor for extruder drive 0 is connected to endstop input 3 (E0), S=23.5mm/rev, R=50% error detection tolerance, C=3mm comparison length

M591 D0 ; display filament sensor parameters for extruder drive 0[/c]

Still getting [c]Extruder 0 reports too little movement[/c]

the strange thing is that The S parameters is set to 23.5 while after M591 D0 I get :
[c]M591 D0
Pulse-type filament monitor on endstop input 3, enabled, sensitivity 28.80mm/pulse, allowed movement 50% to 160%, check every 3.0mm, current position 0.0, no calibration data[/c]
the S parameter is 28.8 instead of 23.5

I will be more than happy to send you one HC-020K encoder, just send me the adress to info@3dbnz.com and on Monday UPS will collect the parcel.

in the mean time, thank you

[paboman]

setting the sensitivity very low to 0.2 makes the print goes thru
then issuing M591 D0
I get [c]Pulse-type filament monitor on endstop input 3, disabled, sensitivity 28.80mm/pulse, allowed movement 20% to 160%, check every 3.0mm, current position 0.0, measured sensitivity 160.73mm/pulse, measured minimum 0%, maximum 2877% over 63648.7mm [/c]
so i set S value to 160 but then i get again:
[c]Extruder 0 reports too little movement[/c]
and the printer go to pause

PS
while the S is 0.2 there is no difference if I remove the sensor from the wheel, the print does not go to pause

Why M591 D0 is telling me [c]disabled[/c] ?

[dc42]

As I said, I brought the parameters into line with the other filament monitors. So S now enables or disables filament monitoring, and L sets the sensitivity. See https://duet3d.dozuki.com/Wiki/Gcode#Section_M591_Configure_filament_sensing.

You will probably need to increase the E parameter.

160mm/pulse sounds far too high. Can you measure it?

[paboman]

what P parameter should I use?
still P7 for pulse-generating sensor or P3 for rotating magnet sensor ?

One complete rotation of the wheel is 20 pulses
Encoder wheel diameter is 26mm
E0 stepes per mm is 1166 ( 13to1 gearbox ratio)

[dc42]

Strill P7.

Are you saying that 26mm filament movement give 20 pulses? If so that's 1.3mm per pulse.

I've put a new firmware binary with more sensible default values at https://www.dropbox.com/s/iq9pzfaugyfei7x/Duet2CombinedFirmware.bin?dl=0.

[paboman]

Diameter of the encoder wheel is 26mm so the circumference is 26 x 3.1416 = 81.7 mm
So 81.7mm of extruded filament is one full turn of the encoder wheel which gives 20 pulses
81.7 / 20 = 4
if so 4mm per pulse

upgraded to: 1.21RC5+ (2018-03-18 build 1)

with this config.g:
[c]; Filament Monitor HC-020K
M591 D0 P7 C3 S0 R70:130 L4.1 E50 ; D= sensor for extruder drive 0, C= E0 endstop input, P=Sensor type, S1= Enable, R=70% to 130% tolerance, L= mm/pulse, E= detection length
M591 D0 ; display filament sensor parameters for extruder drive 0[/c]

i get this response:
[c]10:16:26M591 D0
Pulse-type filament monitor on endstop input 3, disabled, sensitivity 4.10mm/pulse, allowed movement 70% to 130%, check every 50.0mm, current position 0.0, measured sensitivity 12778.21mm/pulse, measured minimum 0%, maximum 33% over 1763392.6mm
10:14:15M591 D0
Pulse-type filament monitor on endstop input 3, disabled, sensitivity 4.10mm/pulse, allowed movement 70% to 130%, check every 50.0mm, current position 0.0, measured sensitivity 12296.81mm/pulse, measured minimum 0%, maximum 25% over 479575.5mm[/c]

If I enable the monitor with S1 i get "Extruder 0 reports too little movement":
[c]10:18:18Printing paused
10:18:17Resume-after-power-fail state saved
10:18:16M591 D0
Pulse-type filament monitor on endstop input 3, enabled, sensitivity 4.10mm/pulse, allowed movement 70% to 130%, check every 50.0mm, current position 0.0, measured sensitivity 25.00mm/pulse, measured minimum 16%, maximum 16% over 50.0mm[/c]

The strange thing is the measured sensitivity of 12778.21mm/pulse while monitor is disabled

[dc42]

So the filament runs on the outside of the 26mm diameter encoder wheel?

The measured sensitivity is clearly absurd, as is the recorded extrusion amount (1.76km in the first report). I'll take another look at the code.

[paboman]

yes, the filament runs on the outside diameter of the 26mm encoder wheel for now. later I will change that to a smaller diameter

[dc42]

I found a likely explanation for the absurd values. Please pick up a new binary from https://www.dropbox.com/s/iq9pzfaugyfei7x/Duet2CombinedFirmware.bin?dl=0.

[paboman]

ok, upgraded the firmware, now im getting "Extruder 0 reports too much movement"
also reducing the E Value from 50 to 10 gives the same result
[c]11:18:53M591 D0
Pulse-type filament monitor on endstop input 3, enabled, sensitivity 4.10mm/pulse, allowed movement 70% to 130%, check every 10.0mm, current position 0.0, measured sensitivity 0.66mm/pulse, measured minimum 439%, maximum 801% over 22.5mm[/c]

[dc42]

Are you certain that he pulse rate of your encoder is 4.10mm of filament per pulse? What happens if you set it to 0.66mm as reported by the calibration?

I'll have the calibration value reported to 3 decimal places in the next build.

[paboman]

Correct me if I am wrong, the 4.1mm per pulse is given by this calculation:
Diameter of the encoder wheel is 26mm so the circumference is 26 x 3.1416 = 81.7 mm
So 81.7mm of extruded filament is one full turn of the encoder wheel which gives 20 pulses (the wheel have 20 slots thru light can pass)
81.7 / 20 = 4.085
I rounded it to 4.1

As you said with L= 0.66 I get "Extruder 0 reports too much movement"
[c]
Pulse-type filament monitor on endstop input 3, enabled, sensitivity 0.66mm/pulse, allowed movement 70% to 130%, check every 10.0mm, current position 0.0, measured sensitivity 0.59mm/pulse, measured minimum 60%, maximum 168% over 21.3mm[/c]

so I changed L= 0.59 but I get "Extruder 0 reports too little movement"

[c]
Pulse-type filament monitor on endstop input 3, enabled, sensitivity 0.59mm/pulse, allowed movement 70% to 130%, check every 10.0mm, current position 0.0, measured sensitivity 0.80mm/pulse, measured minimum 39%, maximum 111% over 42.6mm[/c]

then I changed L= 0.80 but I get "Extruder 0 reports too much movement"

[c]Pulse-type filament monitor on endstop input 3, enabled, sensitivity 0.80mm/pulse, allowed movement 70% to 130%, check every 10.0mm, current position 0.0, measured sensitivity 0.94mm/pulse, measured minimum 83%, maximum 86% over 20.7mm
[/c]

[dc42]

Can you post a photo of how you are using that encoder to measure filament movement?

The calibration data indicates that there is quite a large variation in the amount of extrusion commander per revolution of the wheel. One possible reason for that may be that when filament is retracted, it doesn't force the wheel to rotate backwards because you haven't constrained the filament path sufficiently; so that when forward extrusion is commanded after a retraction, initially the wheel doesn't rotate because there is slack filament to take up.

Unless you can make it more reproducible, you will need to increase the allowed tolerance. For example, when you had the sensitivity set to 0.66 it reported:

measured minimum 60%, maximum 168%

which means that in order to avoid spurious alarms you would need to use R60:168 or wider, not the R70:130 that you are currently using.

[paboman]

In the youtube link you can see my test setup: https://youtu.be/0md1yE183kc

The encoder wheel is directly connected to the stepper shaft, that way the encoder is reading the real revolution of the extruder and no slippage may occur as no filament is being pulled.
This setup is simulating the filament being pulled by the extruder gear and consequently rotating the encoder wheel with a perfect ratio of 1:1. This way im taking out of the equation any filament slippage, dont you think so?
Secondly the Gcode I am running is without retraction.