Minor Issues calibrationg the Printer
this is my first Project runing Reprap Firmware and the duet3d controller board. before that i was using Marlin and Repertier FIrmeware.
First of all iam very fascinated of the Duet3d because of all of the possibilitys you can do with it.
Iam using the Duet WIfi and the Duex5 because iam running on 8 Motors. Iam Using the automatic bed Leveling with 3 independent Motors and the Precision Piezo as a trigger.
Iam also using two Extruder and two Motors for die X-Axis and one for die Y-Axis. all of that works prety good and my results looks pretty good too, instead of the corners..
Iam Using a Bowden Setup with an E3D Titan extruder. The bowden length is 800mm wich means i need a lot oif retraction and a lot of retraction speed so i saw the pressure advance article on the Doku site and tried to configure it.. but when i use the pressure advance my extruder is starting to make a wierd mechanical noise, not like fiolament grinding it sounds really mechanic… and that with an S value of 0.1.. maybe there is an Failure and you can help me..
[c]M584 X0:1 U1 Y5 Z2:3:4 V3:4 E6:7 P3 ; Apply custom drive mapping
M671 X586.14:-35.86:-35.85 Y202.7:399.7:85.7 S5 ; leadscrews at front middle, front rear left and rear right
M350 X16:16 U16 Y16 Z16:16:16 V16:16 E16:16 I1 ; Configure microstepping with interpolation
M92 X64:64 U64 Y64 Z1600:1600:1600 V1600:1600 E396:396 ; Set steps per mm
M566 X300:300 U300 Y300 Z60:60:60 V60:60 E600:600 ; Set maximum instantaneous speed changes (mm/min)
M203 X21000:21000 U21000 Y21000 Z180:180:180 V1800:1800 E4800:4800 ; Set maximum speeds (mm/min)
M201 X2000:2000 U2000 Y2000 Z250:250:250 V250:250 E500:500 ; Set accelerations (mm/s^2)
M906 X1600:1600 U1600 Y1500 Z1400:1400:1400 V1400:1400 E1600:1600 I60 ; Set motor currents (mA) and motor idle factor in per cent
M84 S30 ; Set idle timeout
M572 D0 S0.1 ; pressure advance [/c]
this is the result with coasting, retraction and pressure advance
i cant quite see a difference with or without the pressure advance.. I thing those blobs happen between a layer change. so it seems like there is to much pressure in the bowden system..
the other thing that i have problems with is the Precision piezo.. i cannot configure it.. it is so sensitiv that even if i pet my case really slightly it triggers.. i checked the polarisation and turned on the screw but nothing happens is there any opportunity to configure the sensitivity in the config.g file ?
M558 P1 I1 R2 F100 X0 Y0 Z0 ; Set Z probe type to unmodulated and the dive height + speeds
G31 X0 Y0 Z0 P400 ; Set Z probe trigger value, offset and trigger height
M557 X15:485 Y15:485 S40 ; Define mesh grid[/c]
sorry for the bad english, i think the last time i was writing so long sentences was in 8th grade
I use a Titan extruder (1.75mm) on my delta with a 1.8deg motor too, and pressure advance is working well. These are my extruder settings:
M906 X1000 Y1000 Z1000 E800 ; Set motor currents (mA)
M201 X3000 Y3000 Z3000 E1000 ; Accelerations (mm/s^2)
M203 X18000 Y18000 Z18000 E3600 ; Maximum speeds (mm/min)
M566 X600 Y600 Z600 E600 ; Maximum instant speed changes
I'll leave the piezo question for DjDemonD to answer.
Thanks for the quick response.. your settings seems similar to mines.. i made a video from that noice and uploaded it on youtube.. that sound is not normal i think.. but did you saw the picture ?
i made another test print with retraction/coasting off only with pressure advance from S0-0.5 and i see no difference between the settings..
or maybe there are some other issues.. its the 3rd day in row iam triying to figure out how to get shape corners…
so nobody got a clue?
Phaedrux last edited by
The way the blobs kind of alternate it seems like you might have some Z artifacts.