DuetWIFI migration
-
David, I have now updated to the latest package of files (1.15-b3 etc) and things are quite stable.
I aslo tested the DWC.bin that I built with the shell script I wrote and it works fine too. I think you can include it for further testing. I put a copy on my dropbox here: https://dl.dropboxusercontent.com/u/45673517/dwcspiffs.sh
cheers,
Michael -
I'm glad you solved it. I think I mentioned before in one of these threads that once the Duet becomes disconnected form the access point, it doesn't attempt to reconnect. That's why you had to stop and restart the wifi module in order to connect again. In the next release I'll add support for monitoring the connection status and attempt to re-connect if it becomes disconnected.
Thanks for the build script, I've added it t github.
-
Great, thanks David.
I'm commissioning one of your IR probes on this Rostock Max with the Duet WiFi. I can do head to head comparisons with the FSRs. But I've been chasing an issue with FSRs on this machine as I described in an email I sent a few days ago.
Like all things, there are tradeoffs. I like the simplicity of mounting FSRs and the fact that the nozzle tip is the probe, but the downside is the "force".
-
The important things to achieve when not using the nozzle as the probe are:
1. Reduce varying effector tilt with XY position as far as possible, because such tilt changes the relative heights of the nozzle and the probe. I now have a bulls eye spirit level mounted on the effector so that I can see any tilt.
2. Mount the probe as close to the nozzle as is safe and practical to do so, to minimise the effect of that tilt. That's why I made the IR sensor shallow enough to fit below the heatsink of an E3Dv6 hot end.
Probing with the nozzle itself has the advantage of not being affected by effector tilt - although effector tilt is a sign of geometrical errors that will cause calibration inaccuracies anyway. But I'm not sure I would want to probe my PEI-covered bed with a hot nozzle.
-
I'm almost done with my mount. I have a very non-standard setup with a CNCd effector and a modified E3D V6 that is water cooled and fitted with a Volcano. My mount is adjustable both up & down and in & out so I can dial in the position to optimize it. I'll post some photos once I have it complete.
Do you find the bulls eye spirit level is sensitive enough to show tilt?
-
The bulls eye spirit level was sensitive enough to reveal a tilt when the effector was close to one of the towers. The rods are accurately made to equal lengths, so I corrected it by rotating the carriage on the carriage truck.
-
Here's the IR Probe mount I made for the TrickLaser MetalMax effector along with my custom water cooled E3D V6 hotend and volcano. The clearances look closer in the photos, I'll put Kapton tape on the backside of the board t be safe but I think I'm ok. The mounting system can slide up and down (slots in the printed red mount) and forward back (a slot in the mounting ear on the red mount) so I can fine adjust the probe position.
Next step is to wire it up to the Duet WiFi and get it running.
-
It looks like you could trim the component wire stubs on the back of the board a little more.
One concern I have with that cantilevered sensor mount is that the plastic part only needs to soften and warp very slightly to change the relative heights of the sensor and the nozzle.
-
Thanks David, yes I did that and then Kapton tape. I'l keep an eye on the plastic part. It is mounted to aluminum - a big heat sink and it is very far away from the heater. Worse case I'll machine one in aluminum but I wanted to try this out quickly.
-
David, I seem to be missing something trying to setup the IR probe. I followed the instructions on your blog. That all went well. https://miscsolutions.wordpress.com/mini-height-sensor-board/
When I get to the part to test and configure the probe I do as you say:
heat the nozzle (and bed)
home
lower the head until the nozzle touches the bed (paper test)
issue G92 Z0 (and I see Z set to 0 in DWC)
raise head 5mm
issue G30 S1
the Z value I read off in DWC is 1.0mmI use this value to update my config.g:
M558 P1 X0 Y0 Z0 H5 F500 T12000
G31 P400 Z1.0And reload config.g when asked.
Now, I home and run auto calibrate. When done, it seems like my Z=0 is set about 1mm above the bed. What am I missing?
FYI: bed is PrintBite
-
Micheal, it's G30 S-1 you need to run to measuring the trigger height, not G30 S1.
-
Thanks David! Literally, in my browser looking at https://miscsolutions.wordpress.com/mini-height-sensor-board/ I see:
define that position as Z=0. Raise the head 5mm and remove the paper. Then send G30 S-
1 to probe the bed at that point without adjusting the Z height setting. Read off the Z
height and use that value for the Z parameter in your G31 command in config.g. PleaseI guess my mind saw the "-" and figured it was a continuation to the next line.
-
Thanks for pointing this out. I just checked, and I see exactly the same. I'll re-word the paragraph to prevent the text wrapping at that point. [Edit: I just did that.]
-
Minor thing but those of us with bifocals appreciate it!
Things are working well now. Starting to do some more complicated printing. So far so good. The steppers are much much quieter.
-
Please tell us how you like the printbite compared to pei!
-
They are different beasts @bot. I still prefer (and only use) PEI for my production fly fishing reels as it leaves a perfect matte finish. PrintBite leaves a textured finish. But, PrintBite works with a wide variety of materials that PEI doesn't (PEI is really restricted to ABS, PLA and HIPS) like Nylon, NinjaFlex, PET, PVA. If you don't have a preference for the surface finish, it is good stuff.
-
By the way, no network disconnects for over 24 hrs.
-
By the way, no network disconnects for over 24 hrs.
Thanks for the update! For those who were getting just occasional network disconnects, the single retry I added for status poll requests should fix that. Using the default Ajax timeout of 8 seconds, I find that the retry can generally handle the board being reset too..
-
David, I have finished making a suitable PEI bed to use with the IR probe following the instructions on your blog (painted back side, bake in oven). I then recalibrate the probe and that seemed to go well. But…
My calibration is bad (typical deviation of 0.086) but very good when I switch over to my FSRs (I have them both installed so it is very easy to change from FSR to IR Probing) it is pretty good (deviation 0.45) although not as good as I'd like.
Some questions...
I scuff the surface of my PEI with very fine sandpaper (600 grit) to leave a matte finish on my parts. I installed this PEI with the original glossy side up (painted the matte side as per your instructions) and then scuffed the top. Do you think this would have any effect on the sensor? I wouldn't think so if PEI is IR transparent. -
I don't think it would make much difference which way up you put the PEI. I think the next thing for you to do is to measure the trigger height at a few widely-separated probe points. If you find significant differences, then use feeler gauges to see whether they are due to the edge of the sensor board being at different heights when the nozzle is touching the bed - which would indicate that effector tilt is a problem..
