LaErrors, should I care about them? S3D
-
I noticed I am getting some LaErrors on 2.02 firmware. Is this due I am using Simplify3D? I know it doesn't produce good quality g-code (as I remember the segment length isn't even).
M122 === Diagnostics === RepRapFirmware for Duet 2 WiFi/Ethernet version 2.02(RTOS) running on Duet WiFi 1.02 or later Board ID: 08DGM-9568A-F23SD-6JTDG-3SD6P-1UN7D Used output buffers: 3 of 20 (16 max) === RTOS === Static ram: 25524 Dynamic ram: 98624 of which 0 recycled Exception stack ram used: 512 Never used ram: 6412 Tasks: NETWORK(ready,544) HEAT(blocked,1176) MAIN(running,3868) IDLE(ready,200) Owned mutexes: === Platform === Last reset 11:55:08 ago, cause: software Last software reset at 2019-02-08 22:23, reason: User, spinning module GCodes, available RAM 6324 bytes (slot 2) Software reset code 0x0003 HFSR 0x00000000 CFSR 0x00000000 ICSR 0x0041f000 BFAR 0xe000ed38 SP 0xffffffff Task 0x4e49414d Error status: 0 Free file entries: 10 SD card 0 detected, interface speed: 20.0MBytes/sec SD card longest block write time: 134.4ms, max retries 0 MCU temperature: min 28.4, current 32.2, max 34.6 Supply voltage: min 0.3, current 0.6, max 27.7, under voltage events: 1, over voltage events: 0, power good: no Driver 0: standstill, SG min/max 0/1023 Driver 1: standstill, SG min/max 0/1023 Driver 2: standstill, SG min/max 0/1023 Driver 3: standstill, SG min/max 0/1023 Driver 4: standstill, SG min/max not available Date/time: 2019-02-09 10:18:35 Cache data hit count 4294967295 Slowest loop: 102.71ms; fastest: 0.06ms I2C nak errors 0, send timeouts 0, receive timeouts 0, finishTimeouts 0 === Move === Hiccups: 0, StepErrors: 0, LaErrors: 118, FreeDm: 240, MinFreeDm: 148, MaxWait: 166516ms, Underruns: 0, 0 Scheduled moves: 0, completed moves: 0 Bed compensation in use: none Bed probe heights: 0.000 0.000 0.000 0.000 0.000 === Heat === Bed heaters = 0 -1 -1 -1, chamberHeaters = -1 -1 Heater 0 is on, I-accum = 0.1 Heater 1 is on, I-accum = 0.6 === GCodes === Segments left: 0 Stack records: 3 allocated, 0 in use Movement lock held by null http is idle in state(s) 0 telnet is idle in state(s) 0 file is idle in state(s) 0 serial is idle in state(s) 0 aux is idle in state(s) 0 daemon is idle in state(s) 0 queue is idle in state(s) 0 autopause is idle in state(s) 0 Code queue is empty. === Network === Slowest loop: 135.87ms; fastest: 0.00ms Responder states: HTTP(0) HTTP(0) HTTP(0) HTTP(0) FTP(0) Telnet(0) Telnet(0) HTTP sessions: 1 of 8 - WiFi - Network state is running WiFi module is connected to access point Failed messages: pending 0, notready 0, noresp 0 WiFi firmware version 1.22 WiFi MAC address 60:01:94:34:3e:4b WiFi Vcc 3.38, reset reason Turned on by main processor WiFi flash size 4194304, free heap 29520 WiFi IP address 192.168.88.12 WiFi signal strength -55dBm, reconnections 0, sleep mode modem Socket states: 0 0 0 0 0 0 0 0 -
@dragonn, please make the GCode file available to me and I will look into it.
-
Sure, no problem
https://www.dropbox.com/s/1rei041f33wfwkb/Tolerance_tester (1).gcode?dl=0
I also attached my config.g if it will be needed
0_1549704851966_config (1).g -
Thanks, please leave them there because it will be several days before I can retrieve them.
Last time LA errors were reported it turned out to be a rounding issue and print quality was not affected.
