@jay_s_uk
I still have to install Ballscrews an mount my motors so I might try to wait it out

@dc42
Is the duet 3 capable of driving the motors directly?

@jay_s_uk

That’s ok, I’m not in a rush. In the meantime I want to keep building so I’d like engage with you on the rest of the system so I get it right.

Can that be done offline? It would just be easier is all.

mccaw.d@gmail.com

Also, to clarify my intent.

I’d like to get a complete kit from you that will allow me to build a multi use control panel that will allow me to move my motors between a number of machines. Mill, lathe, router, 3D printer, scanner ect.

I’d like to be able to setup machine profiles in the software to drive the different systems.

I’ve probably gone overkill on the (350w x4), drivers and motors and installed them into a mobile cabinet.

I’ll be installing breakers, surge protection and line filters into the panel.

Your system seems to be very intuitive and from what I’ve seen if it could be done then you’d be the people doing it.

I’m happy to incorporate anything you think appropriate to ensure a good outcome.

Thanks and regards

Dave

This is the eBay link

https://www.ebay.com.au/itm/174181904398

Hi, this is the detail given by the supplier in the kit.

1 x Closed Loop Stepper Driver 0-8.5A 20-80VAC/30-110VDC for Nema 34 Stepper Motor
1 x E Series Nema 34 Closed Loop Stepper Motor 12.0 Nm(1699.68oz.in) Encoder 1000CPR
1 x 1.7 m(67") Long Encoder Extension Cable for Closed Loop Stepper Driver
1 x RV-4 AWG18 1.7 m(67") Long Motor Extension Cable with GX16 Aviation Plug
Motor Specification
Part Number: 34HE59-6004D-E1000
Number of phase: 2
Holding Torque: 12.0 Nm(1699.68oz.in)
Rated Current/phase: 6.0 A
Phase Resistance: 0.7 ohms± 10%
Inductance: 7.9 mH ± 20%(1KHz)
Frame Size: 86 x 86 mm
Body Length: 150.5 mm
Shaft Diameter: Φ14 mm
Shaft Length: 37 mm
Keyway Shaft Length: 25 mm
Lead Length: 300 mm
Encoder Specification
Driving Voltage : 5V
Output current : 55mA
Resolution : 1000cpr
Output Signal : 2 Channels
Bore Diameter : Φ8mm
Output Frequency : ≤1MHz
Running Speed : ≤5000rpm
Driver Specification
Output Peak Current: 0~8.5A（0~6 RMS）
Input Voltage: 20~80VAC/30~110VDC (Typical 48/60VDC)
Logic Signal Current: 7~16mA (Typical 10mA)
Pulse Input Frequency: 0~200kHz
Pulse Width: 2.5μS
Built-in positioning and alarm output for easy detection and control
Intelligently regulate current, reduce vibration, noise and heat, and increase efficiency by 35%
With single and double pulse selection function, the factory default is: pulse + direction control
Excellent high-speed performance and rigidity, perfect combination of servo and stepping advantages
Connection
PIN
1
2
3
4
Color
White
Green
Blue
Black
Motor
A+
A-
B+
B-

PIN
2
3
1
13
11
12
Color
Red
White
Black
Blue
Yellow
Green
Encoder
VCC
EGND
EA+
EA-
EB+
EB-

Thanks Jay, any idea as to when the duet 3 will be released?

Hi, I have a 1.5kw mill running 4x NEMA 34 12nm motors and drives. I really like your platform and was wondering if you have a suitable board for my purpose.

Regards
Dave