@garyd9 said in Duet 2 Upgrade Prints coming out stretched:

What type of printer? Cartesian? Delta? CoreXY?

jeez. i actually forgot to mention that

It's a delta. Ill edit my first post to include that info and the config.g file.

Edit: Well the forum doesn't allow that, so here it is:

Printer Information: Delta Printer 300mm diameter 0.9° Steppers

config.g:

; Configuration file for Duet WiFi (firmware version 3)
; executed by the firmware on start-up
;
; generated by RepRapFirmware Configuration Tool v3.2.0 on Wed Jan 06 2021 12:03:41 GMT+0100 (Central European Standard Time)

; General preferences
G90                                            ; send absolute coordinates...
M83                                            ; ...but relative extruder moves
M550 P"Reese"                                  ; set printer name
M665 R178.07 L360.24 B150 H495 X-0.06° Y0.05°                 ; Set delta radius, diagonal rod length, printable radius and homed heights
M666 X0 Y0 Z0                                  ; put your endstop adjustments here, or let auto calibration find them

; Network
M551 P"rg21l7m6k"                              ; set password
M552 S1                                        ; enable network
M586 P0 S1                                     ; enable HTTP
M586 P1 S0                                     ; disable FTP
M586 P2 S0                                     ; disable Telnet

; Drives
M569 P0 S1                                     ; physical drive 0 goes forwards
M569 P1 S1                                     ; physical drive 1 goes forwards
M569 P2 S1                                     ; physical drive 2 goes forwards
M569 P3 S1                                     ; physical drive 3 goes forwards
M584 X0 Y1 Z2 E3                               ; set drive mapping
M350 X16 Y16 Z16 E16 I1                        ; configure microstepping with interpolation
M92 X160.00 Y160.00 Z160.00 E415.56            ; set steps per mm
M566 X800.00 Y800.00 Z800.00 E800.00       ; set maximum instantaneous speed changes (mm/min)
M203 X48000.00 Y48000.00 Z48000.00 E3600.00    ; set maximum speeds (mm/min)
M201 X800.00 Y800.00 Z800.00 E1000.00       ; set accelerations (mm/s^2)
M906 X1500 Y1500 Z1500 E1600 I70               ; set motor currents (mA) and motor idle factor in per cent
M84 S30                                        ; Set idle timeout

; Axis Limits
M208 Z0 S1                                     ; set minimum Z

; Endstops
M574 X2 S1 P"!xstop"                                    ; configure sensorless endstop for high end on X
M574 Y2 S1 P"!ystop"                                    ; configure sensorless endstop for high end on Y
M574 Z2 S1 P"!zstop"                                    ; configure sensorless endstop for high end on Z

; Z-Probe
M558 C"^zprobe.in" P8 R0.4 F1000 H10                         ; disable Z probe but set dive height, probe speed and travel speed
G31 P100 X0 Y0 Z-0.1
M556 S78 X0 Y0 Z0                              ; set orthogonal axis compensation parameters
M557 R150 S20                                   ; define mesh grid

; Heaters
M308 S0 P"bedtemp" Y"thermistor" T100000 B4138 ; configure sensor 0 as thermistor on pin bedtemp
M950 H0 C"bedheat" T0                          ; create bed heater output on bedheat and map it to sensor 0
M307 H0 B0 S1.00                               ; disable bang-bang mode for the bed heater and set PWM limit
M140 H0                                        ; map heated bed to heater 0
M143 H0 S120                                   ; set temperature limit for heater 0 to 120C
M308 S1 P"e0temp" Y"thermistor" T100000 B4138  ; configure sensor 1 as thermistor on pin e0temp
M950 H1 C"e0heat" T1                           ; create nozzle heater output on e0heat and map it to sensor 1
M307 H1 B0 S1.00                               ; disable bang-bang mode for heater  and set PWM limit
M143 H1 S280                                   ; set temperature limit for heater 1 to 280C

; Fans
M950 F1 C"fan1" Q200                          ; create fan 0 on pin fan0 and set its frequency
M106 P1 C"FAN0_E0" S0.5 H1 T45                   ; set fan 0 name and value. Thermostatic control is turned on
M950 F2 C"fan2" Q500                           ; create fan 1 on pin fan1 and set its frequency
M106 P2 S0 H-1                                 ; set fan 1 value. Thermostatic control is turned off

; Tools
M563 P0 D0 H1 F0                               ; define tool 0
G10 P0 X0 Y0 Z0                                ; set tool 0 axis offsets
G10 P0 R0 S0                                   ; set initial tool 0 active and standby temperatures to 0C

; Custom settings are not defined
M579 X0.970 Y0.970
; Miscellaneous
M575 P1 S1 B57600                              ; enable support for PanelDue
M501                                           ; load saved parameters from non-volatile memory

Hi,

i just upgraded to a Duet 2 Wifi. I came from an old Duet 0.6 with an older firmware (sorry im not sure which one)

I did not just copy the config.g file but created one using the reprap generator and tweaked some values afterwards.
It basically works as expected. My height map is a weird sawtooth mess, but thats probably due to poor carriage mounting (my linear rails are on the way).

Now the really weird issue: My prints come out stretched in X and Y direction by the same amount. Z seems to be fine though I am not sure. Measuring old prints, it seemed to work just fine before. Am I missing some config parameter which would cause such an issue?
For reference: A 200mm200mm square comes out at about 207mm207mm

Thanks

ok got it thanks!

wow.... im slightly embarrassed now... thank you! also: m500 saves my autocal so i dont have to run it everytime i homed the printer?

@garyd9 said in Duet 2 Upgrade Prints coming out stretched:

Your config.g doesn't show any M665 at all... Do you have that command in a config-override.g? If so, does the "L" parameter match the length of the delta diagonal arms (measured in mm)?

both. its the third command in my config.g (guess you missed it?)and its autogenerated in the config-override

@garyd9 said in Duet 2 Upgrade Prints coming out stretched:

What is the "S" parameter on the final G30 in your bed.g?

I already checked that. its a 6 factor calibration.

The M665 command is kinda weird. It doesnt show the rod length.

m665
Diagonals 350.000:350.000:350.000, delta radius 169.494, homed height 477.998, bed radius 150.0, X -0.251°, Y -0.014°, Z 0.000°

I am using a Smart effector + Haydn Huntley’s Magball delta arms which are specified at 360.24 so I figure this shouldn't be the problem.

@fcwilt said in Duet 2 Upgrade Prints coming out stretched:

It's not really a hack.

Yeah It'll work for sure. but it doesn't fix the root problem.

@garyd9 said in Duet 2 Upgrade Prints coming out stretched:

What type of printer? Cartesian? Delta? CoreXY?

jeez. i actually forgot to mention that

It's a delta. Ill edit my first post to include that info and the config.g file.

Edit: Well the forum doesn't allow that, so here it is:

Printer Information: Delta Printer 300mm diameter 0.9° Steppers

config.g:

; Configuration file for Duet WiFi (firmware version 3)
; executed by the firmware on start-up
;
; generated by RepRapFirmware Configuration Tool v3.2.0 on Wed Jan 06 2021 12:03:41 GMT+0100 (Central European Standard Time)

; General preferences
G90                                            ; send absolute coordinates...
M83                                            ; ...but relative extruder moves
M550 P"Reese"                                  ; set printer name
M665 R178.07 L360.24 B150 H495 X-0.06° Y0.05°                 ; Set delta radius, diagonal rod length, printable radius and homed heights
M666 X0 Y0 Z0                                  ; put your endstop adjustments here, or let auto calibration find them

; Network
M551 P"rg21l7m6k"                              ; set password
M552 S1                                        ; enable network
M586 P0 S1                                     ; enable HTTP
M586 P1 S0                                     ; disable FTP
M586 P2 S0                                     ; disable Telnet

; Drives
M569 P0 S1                                     ; physical drive 0 goes forwards
M569 P1 S1                                     ; physical drive 1 goes forwards
M569 P2 S1                                     ; physical drive 2 goes forwards
M569 P3 S1                                     ; physical drive 3 goes forwards
M584 X0 Y1 Z2 E3                               ; set drive mapping
M350 X16 Y16 Z16 E16 I1                        ; configure microstepping with interpolation
M92 X160.00 Y160.00 Z160.00 E415.56            ; set steps per mm
M566 X800.00 Y800.00 Z800.00 E800.00       ; set maximum instantaneous speed changes (mm/min)
M203 X48000.00 Y48000.00 Z48000.00 E3600.00    ; set maximum speeds (mm/min)
M201 X800.00 Y800.00 Z800.00 E1000.00       ; set accelerations (mm/s^2)
M906 X1500 Y1500 Z1500 E1600 I70               ; set motor currents (mA) and motor idle factor in per cent
M84 S30                                        ; Set idle timeout

; Axis Limits
M208 Z0 S1                                     ; set minimum Z

; Endstops
M574 X2 S1 P"!xstop"                                    ; configure sensorless endstop for high end on X
M574 Y2 S1 P"!ystop"                                    ; configure sensorless endstop for high end on Y
M574 Z2 S1 P"!zstop"                                    ; configure sensorless endstop for high end on Z

; Z-Probe
M558 C"^zprobe.in" P8 R0.4 F1000 H10                         ; disable Z probe but set dive height, probe speed and travel speed
G31 P100 X0 Y0 Z-0.1
M556 S78 X0 Y0 Z0                              ; set orthogonal axis compensation parameters
M557 R150 S20                                   ; define mesh grid

; Heaters
M308 S0 P"bedtemp" Y"thermistor" T100000 B4138 ; configure sensor 0 as thermistor on pin bedtemp
M950 H0 C"bedheat" T0                          ; create bed heater output on bedheat and map it to sensor 0
M307 H0 B0 S1.00                               ; disable bang-bang mode for the bed heater and set PWM limit
M140 H0                                        ; map heated bed to heater 0
M143 H0 S120                                   ; set temperature limit for heater 0 to 120C
M308 S1 P"e0temp" Y"thermistor" T100000 B4138  ; configure sensor 1 as thermistor on pin e0temp
M950 H1 C"e0heat" T1                           ; create nozzle heater output on e0heat and map it to sensor 1
M307 H1 B0 S1.00                               ; disable bang-bang mode for heater  and set PWM limit
M143 H1 S280                                   ; set temperature limit for heater 1 to 280C

; Fans
M950 F1 C"fan1" Q200                          ; create fan 0 on pin fan0 and set its frequency
M106 P1 C"FAN0_E0" S0.5 H1 T45                   ; set fan 0 name and value. Thermostatic control is turned on
M950 F2 C"fan2" Q500                           ; create fan 1 on pin fan1 and set its frequency
M106 P2 S0 H-1                                 ; set fan 1 value. Thermostatic control is turned off

; Tools
M563 P0 D0 H1 F0                               ; define tool 0
G10 P0 X0 Y0 Z0                                ; set tool 0 axis offsets
G10 P0 R0 S0                                   ; set initial tool 0 active and standby temperatures to 0C

; Custom settings are not defined
M579 X0.970 Y0.970
; Miscellaneous
M575 P1 S1 B57600                              ; enable support for PanelDue
M501                                           ; load saved parameters from non-volatile memory

well thats one hell of a dirty hack

ill give it a shot to get at least this print done. thanks.

Hi,

i just upgraded to a Duet 2 Wifi. I came from an old Duet 0.6 with an older firmware (sorry im not sure which one)

I did not just copy the config.g file but created one using the reprap generator and tweaked some values afterwards.
It basically works as expected. My height map is a weird sawtooth mess, but thats probably due to poor carriage mounting (my linear rails are on the way).

Now the really weird issue: My prints come out stretched in X and Y direction by the same amount. Z seems to be fine though I am not sure. Measuring old prints, it seemed to work just fine before. Am I missing some config parameter which would cause such an issue?
For reference: A 200mm200mm square comes out at about 207mm207mm

Thanks