@oliof now, i can use driver 11 after update fw 3.3
tks u very much

@oliof now, i can use driver 11 after update fw 3.3
tks u very much

@oliof tks very much, i will try up to FW 3.3, i have use fw 3.2

Hello, i have 2 driver HBS57 wiring
https://i0.wp.com/s1.uphinh.org/2021/09/14/image110877081bb6fcce.png
I connect:
PUL+ of driver 1 with 9)Stp 10 (LCD_DB5)
DIR+ of driver 1 with 7)Dir 10 (LCD_DB6)
ENA+ of driver 1 (no connect)
PUL+ of driver 2 with 10)Stp 11 (LCD_DB4)
DIR+ of driver 2 with 8)Dir 11 (LCD_E)
ENA+ of driver 2 (no nonnect)
PUL- and DIR- of driver 1,2 with 2) GND
Only driver 1 work, i swap driver 1 to driver 2 but only driver connect with Stp 10 and Dir 10 work, Stp 11 and Dir 11 not work.
My firmware:
; Configuration file for Duet WiFi (firmware version 3)
; executed by the firmware on start-up
; generated by RepRapFirmware Configuration Tool v3.2.3 on Wed Feb 24 2021 21:49:41 GMT+0700 (Indochina Time)
;PanelDue
M575 P1 B57600 S1

; General preferences
G90 ; send absolute coordinates...
M83 ; ...but relative extruder moves
M550 P"HMQ Printer" ; set printer name
M669 K1 ; select CoreXY mode

; Network
M552 S1 ; enable network
M586 P0 S1 ; enable HTTP
M586 P1 S0 ; disable FTP
M586 P2 S0 ; disable Telnet

; Drives
M569 P0 S1 ; physical drive 0 goes forwards
M569 P1 S1 ; physical drive 1 goes forwards
M569 P2 S1 ; physical drive 2 goes forwards
M569 P3 S1 ; physical drive 3 goes forwards
M569 P4 S0 ; physical drive 4 goes forwards
;M569 P5 S0 ; physical drive 3 goes forwards
M569 P10 S0 ; physical drive 3 goes forwards
;M569 P11 S1 ; physical drive 3 goes forwards
M569 P5 S1 T5:2.5:5:7.5 ; physical drive 3 goes forwards
M569 P7 S1 T5:2.5:5:7.5 ; physical drive 3 goes forwards
M584 X10 Y11 Z0:1:3 E4 ; set drive mapping

M671 X24:292:155 Y35:35:300 S10 ;Toa do can ban ma tran
M350 X16 Y16 Z16 E16 I1 ; configure microstepping with interpolation
M92 X250 Y250 Z800 E394 ; set steps per mm
M566 X900.00 Y900.00 Z60.00 E120.00 ; set maximum instantaneous speed changes (mm/min)
M203 X6000.00 Y6000.00 Z180.00 E1200.00 ; set maximum speeds (mm/min)
M201 X500.00 Y500.00 Z10.00 E250.00 ; set accelerations (mm/s^2)
;M201 X10000 Y10000 Z10 E250 ; test gia toc cao
M906 X800 Y800 Z800 E800 I30 ; set motor currents (mA) and motor idle factor in per cent
M84 S30 ; Set idle timeout

; Axis Limits
M208 X0 Y0 Z0 S1 ; set axis minima
M208 X288 Y285 Z300 S0 ; set axis maxima

; Endstops
M574 X1 S1 P"xstop" ; configure sensorless endstop for high end on X
M574 Y1 S1 P"ystop" ; configure sensorless endstop for high end on Y
M574 Z1 S2 ; Define Z to use Probe. Home to Min

; Z-Probe
;M950 S0 C"duex.pwm5" ; create servo pin 0 for BLTouch
M558 P5 C"!^zprobe.in" I1 ; set chan cam bien Z
;M558 P9 C"^zprobe.in" H5 F120 T6000 ; set Z probe type to bltouch and the dive height + speeds
;M280 P0 S90 ;send control signal to BLTouch through servo/gpio 0
G31 P500 X4 Y35 Z1.85 ; set Z probe trigger value, offset and trigger height
M557 X4:292 Y35:320 S19.1:18.9 ; define mesh grid

; Heaters
M308 S0 P"bedtemp" Y"thermistor" T100000 B4138 ; configure sensor 0 as thermistor on pin bedtemp
M950 H0 C"bedheat" T0 ; create bed heater output on bedheat and map it to sensor 0
M307 H0 B1 R0.896 C85.5 D1.72 S1.00 V24
;M307 H0 B0 S1.00 ; disable bang-bang mode for the bed heater and set PWM limit
M140 H0 ; map heated bed to heater 0
M143 H0 S120 ; set temperature limit for heater 0 to 120C
M308 S1 P"e0temp" Y"thermistor" T100000 B4138 ; configure sensor 1 as thermistor on pin e0temp
M950 H1 C"e0heat" T1 ; create nozzle heater output on e0heat and map it to sensor 1
;M307 H1 R2.573 C78.2 D5.54 S1.00 V24
M307 H1 B0 S1.00 ; disable bang-bang mode for heater and set PWM limit
M143 H1 S280 ; set temperature limit for heater 1 to 280C

; Fans
M950 F0 C"fan0" Q500 ; create fan 0 on pin fan0 and set its frequency
M106 P0 S0 H-1 ; set fan 0 value. Thermostatic control is turned off
M950 F1 C"fan1" Q500 ; create fan 1 on pin fan1 and set its frequency
M106 P1 S1 H1 T45 ; set fan 1 value. Thermostatic control is turned on

; Tools
M563 P0 D0 H1 F0 ; define tool 0
G10 P0 X0 Y0 Z0 ; set tool 0 axis offsets
G10 P0 R0 S0 ; set initial tool 0 active and standby temperatures to 0C

; Custom settings are not defined
;G29 S1 ; Load height map from file

; Miscellaneous
T0 ; select first tool
Pls help me

@dc42 pls help me connect driver 11 of duet 2 wifi with HBS57 driver, i have 2 driver HBS57 and conect with driver 10 and 11 on CONN_LCD.
Pin 9) Stp 10 with PUL+ of driver HBS number 1
Pin 7) Dir 10 with DIR+ of driver HBS nunber 1
Pin 5) En 10
Pin 3) Stop 10
Pin 1) 3.3v
Pin 10) Stp 11 with PUL+ of driver HBS number 2
Pin Dir 11 with DIR+ of driver HBS number 2
Pin 6) En 11
Pin 4) Stop 11
Pin 2) GND with PUL-, DIR- of driver HBS number 10 and 11
But only driver 1 work, driver 2 not work.
I try swap driver 1 to driver 2 but not work on driver connect with Stp 11 and Dir 11

@Exerqtor can i use tmc2208 for stepper driver modula a4988/drv8825 ?