@phaedrux Ok will do, thanks again!

@phaedrux @phaedrux Well thank you so much, that worked. It looks like in the reprap configuration tool I had left a part cooling fan, and as you said I don't have one hooked up at the moment (I need to print a new mount and air duct first). In subsequent configurations I haven't had the problem, it now reads F0 instead of F-1 by default, so I think it was my fault all along. Are there any resources you recommend for learning more about the g code commands, particularly the diagnostic commands? It looks like knowledge in that area is going to be important moving forward with a duet controlled printer.

@phaedrux Ok the results for M122 were:
7/29/2021, 2:26:17 PM M122
=== Diagnostics ===
RepRapFirmware for Duet 2 WiFi/Ethernet version 3.3 (2021-06-15 21:44:54) running on Duet WiFi 1.02 or later
Board ID: 08DLM-996RU-N85S4-7JKD4-3SS6K-TA8RQ
Used output buffers: 3 of 24 (11 max)
=== RTOS ===
Static ram: 23876
Dynamic ram: 74504 of which 128 recycled
Never used RAM 15908, free system stack 184 words
Tasks: NETWORK(ready,11.0%,252) HEAT(delaying,0.0%,336) Move(notifyWait,0.1%,364) MAIN(running,84.2%,407) IDLE(ready,4.7%,29), total 100.0%
Owned mutexes: WiFi(NETWORK)
=== Platform ===
Last reset 00:00:19 ago, cause: power up
Last software reset at 2021-07-29 00:31, reason: User, GCodes spinning, available RAM 15908, slot 0
Software reset code 0x0003 HFSR 0x00000000 CFSR 0x00000000 ICSR 0x0041f000 BFAR 0xe000ed38 SP 0x00000000 Task MAIN Freestk 0 n/a
Error status: 0x00
Step timer max interval 0
MCU temperature: min 31.0, current 34.5, max 34.6
Supply voltage: min 23.7, current 23.8, max 23.9, under voltage events: 0, over voltage events: 0, power good: yes
Heap OK, handles allocated/used 0/0, heap memory allocated/used/recyclable 0/0/0, gc cycles 0
Driver 0: position 0, standstill, SG min/max not available
Driver 1: position 0, standstill, SG min/max not available
Driver 2: position 0, standstill, SG min/max not available
Driver 3: position 0, standstill, SG min/max not available
Driver 4: position 0, standstill, SG min/max not available
Driver 5: position 0
Driver 6: position 0
Driver 7: position 0
Driver 8: position 0
Driver 9: position 0
Driver 10: position 0
Driver 11: position 0
Date/time: 2021-07-29 14:26:16
Cache data hit count 744932926
Slowest loop: 5.35ms; fastest: 0.16ms
I2C nak errors 0, send timeouts 0, receive timeouts 0, finishTimeouts 0, resets 0
=== Storage ===
Free file entries: 10
SD card 0 detected, interface speed: 20.0MBytes/sec
SD card longest read time 3.1ms, write time 0.0ms, max retries 0
=== Move ===
DMs created 83, maxWait 0ms, bed compensation in use: none, comp offset 0.000
=== MainDDARing ===
Scheduled moves 0, completed moves 0, hiccups 0, stepErrors 0, LaErrors 0, Underruns [0, 0, 0], CDDA state -1
=== AuxDDARing ===
Scheduled moves 0, completed moves 0, hiccups 0, stepErrors 0, LaErrors 0, Underruns [0, 0, 0], CDDA state -1
=== Heat ===
Bed heaters = 0 -1 -1 -1, chamberHeaters = -1 -1 -1 -1
=== GCodes ===
Segments left: 0
Movement lock held by null
HTTP is idle in state(s) 0
Telnet is idle in state(s) 0
File is idle in state(s) 0
USB is idle in state(s) 0
Aux is idle in state(s) 0
Trigger is idle in state(s) 0
Queue is idle in state(s) 0
LCD is idle in state(s) 0
Daemon is idle in state(s) 0
Autopause is idle in state(s) 0
Code queue is empty.
=== Network ===
Slowest loop: 15.57ms; fastest: 0.00ms
Responder states: HTTP(0) HTTP(0) HTTP(0) HTTP(0) FTP(0) Telnet(0), 0 sessions
HTTP sessions: 1 of 8

• WiFi -
  Network state is active
  WiFi module is connected to access point
  Failed messages: pending 0, notready 0, noresp 0
  WiFi firmware version 1.26
  WiFi MAC address f4:cf:a2:66:ad:f9
  WiFi Vcc 3.31, reset reason Turned on by main processor
  WiFi flash size 4194304, free heap 24200
  WiFi IP address 192.168.1.16
  WiFi signal strength -62dBm, mode 802.11n, reconnections 0, sleep mode modem
  Clock register 00002002
  Socket states: 0 0 0 0 0 0 0 0

The results from M98 P"config.g" were:
7/29/2021, 2:30:01 PM M98 P"config.g"
HTTP is enabled on port 80
FTP is disabled
TELNET is disabled
Error: in file macro line 58 column 28: M563: expected number after 'F'
Error: Tool 0 not found
Error: Tool 0 not found

If I send T0 in the console it just reads back:
7/29/2021, 2:32:14 PM T0

@phaedrux Just checked, I'm running 3.3.0 on both. Or at least I'm assuming, the M115 command comes back with 3.3 for the board , and the version of my DWC is 3.3.0 .

I'm having a weird problem right now, I just went through the rep-rap configuration tool and configured my extruder (or so I thought). On DWC it displays my bed, but not my extruder tool.

I looked at my configuration.g file, and my tool seems to be listed there, but it's still not showing up on DWC. I also triple checked my wiring, and both the motor and thermister for my hotend seem to be plugged into the correct locations. I'm probably missing something obvious. I am very new to the Duet scene, any help is appreciated. ```
code_text

; executed by the firmware on start-up
;
; generated by RepRapFirmware Configuration Tool v3.2.3 on Wed Jul 28 2021 23:43:42 GMT-0600 (Mountain Daylight Time)

; General preferences
G90                                                    ; send absolute coordinates...
M83                                                    ; ...but relative extruder moves
M550 P"Wilson 2"                                       ; set printer name

; Network
M552 S1                                                ; enable network
M586 P0 S1                                             ; enable HTTP
M586 P1 S0                                             ; disable FTP
M586 P2 S0                                             ; disable Telnet

; Drives
M569 P0 S1                                             ; physical drive 0 goes forwards
M569 P1 S1                                             ; physical drive 1 goes forwards
M569 P2 S1                                             ; physical drive 2 goes forwards
M569 P3 S1                                             ; physical drive 3 goes forwards
M584 X0 Y1 Z2 E3                                       ; set drive mapping
M350 X16 Y16 Z16 E16 I1                                ; configure microstepping with interpolation
M92 X80.00 Y80.00 Z400.00 E107.00                      ; set steps per mm
M566 X900.00 Y30.00 Z30.00 E120.00                     ; set maximum instantaneous speed changes (mm/min)
M203 X6000.00 Y6000.00 Z360.00 E1200.00                ; set maximum speeds (mm/min)
M201 X3000.00 Y1000.00 Z3000.00 E3000.00               ; set accelerations (mm/s^2)
M906 X1200 Y1200 Z1200 E1200 I30                       ; set motor currents (mA) and motor idle factor in per cent
M84 S30                                                ; Set idle timeout

; Axis Limits
M208 X0 Y0 Z0 S1                                       ; set axis minima
M208 X200 Y300 Z180 S0                                 ; set axis maxima

; Endstops
M574 X1 S1 P"xstop"                                    ; configure active-high endstop for low end on X via pin xstop
M574 Y1 S1 P"ystop"                                    ; configure active-high endstop for low end on Y via pin ystop
M574 Z1 S1 P"zstop"                                    ; configure active-high endstop for low end on Z via pin zstop

; Z-Probe
M558 P0 H5 F120 T6000                                  ; disable Z probe but set dive height, probe speed and travel speed
M557 X15:215 Y15:195 S20                               ; define mesh grid

; Heaters
M308 S0 P"bedtemp" Y"thermistor" T100000 B3950         ; configure sensor 0 as thermistor on pin bedtemp
M950 H0 C"bedheat" T0                                  ; create bed heater output on bedheat and map it to sensor 0
M307 H0 B1 S1.00                                       ; enable bang-bang mode for the bed heater and set PWM limit
M140 H0                                                ; map heated bed to heater 0
M143 H0 S60                                            ; set temperature limit for heater 0 to 60C
M308 S1 P"e0temp" Y"thermistor" T100000 B4725 C7.06e-8 ; configure sensor 1 as thermistor on pin e0temp
M950 H1 C"e0heat" T1                                   ; create nozzle heater output on e0heat and map it to sensor 1
M307 H1 B0 S1.00                                       ; disable bang-bang mode for heater  and set PWM limit
M143 H1 S245                                           ; set temperature limit for heater 1 to 245C

; Fans

; Tools
M563 P0 S"Extruder" D0 H1 F-1                          ; define tool 0
G10 P0 X0 Y0 Z0                                        ; set tool 0 axis offsets
G10 P0 R0 S0                                           ; set initial tool 0 active and standby temperatures to 0C

; Custom settings are not defined

@phaedrux Thank you very much! I followed your instructions and they worked. It looks like I had to update the board all the way to version 3.3 before my old version of the DWC upgraded. Onward to the next challenge.

Hello, I'd like to start this off by saying I'm a total Duet noob. I recently purchased a Deut 2 wifi, but it came with an older firmware version (2.05.1), I'm currently trying to update to version 3.0 so that after I can then upgrade to the latest version. I completed the steps to upgrade, the board seems to have upgraded properly, it responds to the M115 command by confirming it is version 3.0. However, my version of the Duet Web Controller Remains outdated at version 2.0.4 . The instructions for updating my board mentioned that uploading the zip file for the new firmware should update "firmware, IAP, WiFi firmware and DWC all at once", I don't know why my version of the DWC remains 2.0.4 . Any help would be greatly appreciated.