Duet3D Logo Duet3D
    • Tags
    • Documentation
    • Order
    • Register
    • Login
    1. Home
    2. christophe31
    • Profile
    • Following 0
    • Followers 0
    • Topics 1
    • Posts 5
    • Best 0
    • Controversial 0
    • Groups 0

    christophe31

    @christophe31

    0
    Reputation
    1
    Profile views
    5
    Posts
    0
    Followers
    0
    Following
    Joined Last Online

    christophe31 Unfollow Follow

    Latest posts made by christophe31

    • RE: BL TOUCH CONFIGURATION

      @DIY-O-Sphere said in BL TOUCH CONFIGURATION:

      @christophe31 said in BL TOUCH CONFIGURATION:

      G1 X50 Y5 F4800 ; go to first probe point

      Adept those lines in both homing files

      yes found everything seems to work fine, thanks a lot again, for your fat answer.
      i'm too happy lol:)

      posted in Firmware installation
      christophe31undefined
      christophe31
    • RE: BL TOUCH CONFIGURATION

      @DIY-O-Sphere said in BL TOUCH CONFIGURATION:

      @christophe31 said in BL TOUCH CONFIGURATION:

      M307 H3 A-1 C-1 D-1 ; disable heater on PWM channel for BLTouch

      Wtch RRF3 version are you using.?
      For the stable you can remove this

      yes i've remove this line

      allelluia my Z homing fonctionning... THANKS A LOT one who know here better than 100 who search..
      the only issue i have is that the homing for the Z is not in the center of my bed, did you know the line to correct?

      posted in Firmware installation
      christophe31undefined
      christophe31
    • RE: BL TOUCH CONFIGURATION

      here my homeall.g:
      G91 ; relative positioning
      G1 H2 Z5 F4800 ; lift Z relative to current position
      G1 H1 X-305 Y-305 F6000 ; move quickly to X and Y axis endstops and stop there (first pass)
      G1 H2 X5 Y5 F4800 ; go back a few mm
      G1 H1 X-305 Y-305 F600 ; move slowly to X and Y axis endstops once more (second pass)
      G90 ; absolute positioning
      G1 X50 Y5 F4800 ; go to first bed probe point and home Z
      G30 ; home Z by probing the bed

      ; Uncomment the following lines to lift Z after probing
      ;G91 ; relative positioning
      ;G1 Z5 F80 ; lift Z relative to current position
      ;G90 ; absolute positioning

      and my homez.g:
      G91 ; relative positioning
      G1 H2 Z5 F4800 ; lift Z relative to current position
      G90 ; absolute positioning
      G1 X50 Y5 F4800 ; go to first probe point
      G30 ; home Z by probing the bed

      ; Uncomment the following lines to lift Z after probing
      ;G91 ; relative positioning
      ;G1 Z5 F80 ; lift Z relative to current position
      ;G90 ; absolute positioning

      posted in Firmware installation
      christophe31undefined
      christophe31
    • RE: BL TOUCH CONFIGURATION

      @DIY-O-Sphere said in BL TOUCH CONFIGURATION:

      @christophe31 said in BL TOUCH CONFIGURATION:

      M558 P9 C"zprobe.in"

      You have to invert the input

      when i delete the " ^ "it's the same issue will look at the other files you say and come back

      posted in Firmware installation
      christophe31undefined
      christophe31
    • BL TOUCH CONFIGURATION

      HI ,
      i'm new with my DUET 2 wifi V1.04 and try to confirgure my Alfawise U20 with it.

      i'm running:
      Duet 2 wifi 1.04
      3.0 firmware
      new BL Touch

      i've follow all the tutorials to configure the BL touch, but still nothing , and i've try many things, my BL touch is plug into:
      z probe in/ GND for Z probe
      +5v/GND and Pin8 HEATER3 for the servos cable

      i've try many change on the file config.g but nothing seems to work and the command S10, S120 result on a bad command in the DWC.

      here my config.g:

      ; Endstops
      M574 X1 S0 P"xstop" ; configure active-low endstop for low end on X via pin xstop
      M574 Y1 S0 P"ystop" ; configure active-low endstop for low end on Y via pin ystop
      M574 Z1 S2 ; configure Z-probe endstop for low end on Z

      ; Z-Probe
      M307 H3 A-1 C-1 D-1 ; disable heater on PWM channel for BLTouch
      M950 S0 C"exp.heater3" ; create servo pin 0 for BLTouch
      M558 P9 C"zprobe.in" H3 F120 T4800 ; set Z probe type to bltouch and the dive height + speeds
      M558 H30 ;*** Remove this line after delta calibration has been done and new delta
      parameters have been saved
      G31 P25 X-35 Y10 Z2.5 ; set Z probe trigger value, offset and trigger height
      M557 X15:285 Y15:285 S20 ; define mesh grid

      ; Heaters
      M307 H3 A-1 C-1 D-1 ; disable heater on PWM channel for BLTouch
      M308 S0 P"bedtemp" Y"thermistor" T100000 B4700 ; configure sensor 0 as thermistor on pin bedtemp
      M950 H0 C"bedheat" T0 ; create bed heater output on bedheat and map it to sensor 0
      M143 H0 S70 ; set temperature limit for heater 0 to 70C
      M307 H0 B0 S1.00 ; disable bang-bang mode for the nozzle heater and set PWM limit
      M308 S1 P"e0temp" Y"thermistor" T100000 B4700 ; configure sensor 1 as thermistor on pin e0temp
      M950 H1 C"e0heat" T1 ; create nozzle heater output on e0heat and map it to sensor 1
      M143 H1 S230 ; set temperature limit for heater 1 to 230C
      M307 H1 B0 S1.00 ; disable bang-bang mode for the nozzle heater and set PWM limit

      my deployprobe.g:
      M280 P0 S10 I1 ; deploy BLTouch
      my retractprobe.g:
      M280 P0 S90 I1 ; retract BLTouch

      did you have some idea of what happen? how to solve.
      thanks
      christophe

      posted in Firmware installation
      christophe31undefined
      christophe31