Posts made by IanWalton

you can see whats in my config.g file further up.
i commented out all the network stuff, rebooted and the wifi led didnt flash

first m122
=== Diagnostics ===
Used output buffers: 1 of 32 (1 max)
=== Platform ===
RepRapFirmware for Duet 2 WiFi/Ethernet version 1.21 running on Duet WiFi 1.02 or later
Board ID: 08DDM-9FAM2-LW4S4-6J1D8-3SD6R-T3SZX
Static ram used: 16152
Dynamic ram used: 100248
Recycled dynamic ram: 2384
Stack ram used: 3576 current, 4504 maximum
Never used ram: 7784
Last reset 00:00:41 ago, cause: software
Last software reset time unknown, reason: User, spinning module GCodes, available RAM 7784 bytes (slot 0)
Software reset code 0x0003 HFSR 0x00000000, CFSR 0x00000000, ICSR 0x0441f000, BFAR 0xe000ed38, SP 0xffffffff
Error status: 0
Free file entries: 10
SD card 0 detected, interface speed: 20.0MBytes/sec
SD card longest block write time: 0.0ms
MCU temperature: min 31.3, current 31.4, max 31.8
Supply voltage: min 12.2, current 12.2, max 12.3, under voltage events: 0, over voltage events: 0
Driver 0: standstill, SG min/max not available
Driver 1: standstill, SG min/max not available
Driver 2: standstill, SG min/max not available
Driver 3: standstill, SG min/max not available
Driver 4: standstill, SG min/max not available
Date/time: 1970-01-01 00:00:00
Slowest main loop (seconds): 0.000153; fastest: 0.000049
=== Move ===
MaxReps: 0, StepErrors: 0, LaErrors: 0, FreeDm: 240, MinFreeDm 240, MaxWait: 0ms, Underruns: 0, 0
Scheduled moves: 0, completed moves: 0
Bed compensation in use: none
Bed probe heights: 0.000 0.000 0.000 0.000 0.000
=== Heat ===
Bed heaters = 0 -1 -1 -1, chamberHeaters = -1 -1
=== GCodes ===
Segments left: 0
Stack records: 1 allocated, 0 in use
Movement lock held by null
http is idle in state(s) 0
telnet is idle in state(s) 0
file is idle in state(s) 0
serial is ready with "M122" in state(s) 0
aux is idle in state(s) 0
daemon is idle in state(s) 0
queue is idle in state(s) 0
autopause is idle in state(s) 0
Code queue is empty.
=== Network ===
Responder states: HTTP(0) HTTP(0) HTTP(0) HTTP(0) FTP(0) Telnet(0) Telnet(0)
HTTP sessions: 0 of 8

• WiFi -
  Network state is disabled
  WiFi module is disabled
  Failed messages: pending 2779096485, notready 2779096485, noresp 2779096485
  Socket states: 0 0 0 0 0 0 0 0
  === Expansion ===

sent m552 s0, no reply on yat
M122 returns

=== Diagnostics ===
Used output buffers: 1 of 32 (9 max)
=== Platform ===
RepRapFirmware for Duet 2 WiFi/Ethernet version 1.21 running on Duet WiFi 1.02 or later
Board ID: 08DDM-9FAM2-LW4S4-6J1D8-3SD6R-T3SZX
Static ram used: 16152
Dynamic ram used: 100448
Recycled dynamic ram: 2184
Stack ram used: 3576 current, 4664 maximum
Never used ram: 7624
Last reset 00:02:15 ago, cause: software
Last software reset time unknown, reason: User, spinning module GCodes, available RAM 7784 bytes (slot 0)
Software reset code 0x0003 HFSR 0x00000000, CFSR 0x00000000, ICSR 0x0441f000, BFAR 0xe000ed38, SP 0xffffffff
Error status: 0
Free file entries: 10
SD card 0 detected, interface speed: 20.0MBytes/sec
SD card longest block write time: 0.0ms
MCU temperature: min 31.1, current 31.9, max 31.9
Supply voltage: min 12.2, current 12.2, max 12.3, under voltage events: 0, over voltage events: 0
Driver 0: standstill, SG min/max not available
Driver 1: standstill, SG min/max not available
Driver 2: standstill, SG min/max not available
Driver 3: standstill, SG min/max not available
Driver 4: standstill, SG min/max not available
Date/time: 1970-01-01 00:00:00
Slowest main loop (seconds): 0.099142; fastest: 0.000049
=== Move ===
MaxReps: 0, StepErrors: 0, LaErrors: 0, FreeDm: 240, MinFreeDm 240, MaxWait: 0ms, Underruns: 0, 0
Scheduled moves: 0, completed moves: 0
Bed compensation in use: none
Bed probe heights: 0.000 0.000 0.000 0.000 0.000
=== Heat ===
Bed heaters = 0 -1 -1 -1, chamberHeaters = -1 -1
=== GCodes ===
Segments left: 0
Stack records: 1 allocated, 0 in use
Movement lock held by null
http is idle in state(s) 0
telnet is idle in state(s) 0
file is idle in state(s) 0
serial is ready with "M122" in state(s) 0
aux is idle in state(s) 0
daemon is idle in state(s) 0
queue is idle in state(s) 0
autopause is idle in state(s) 0
Code queue is empty.
=== Network ===
Responder states: HTTP(0) HTTP(0) HTTP(0) HTTP(0) FTP(0) Telnet(0) Telnet(0)
HTTP sessions: 0 of 8

• WiFi -
  Network state is starting
  WiFi module is disabled
  Failed messages: pending 0, notready 0, noresp 0
  Socket states: 0 0 0 0 0 0 0 0
  === Expansion ===

i did a M122 after the S-1 and the only difference i could see was ''network state is disabled''

M552 S-1returns ''WiFi module stopped''
M552 S0 returns nothing

M122 returns
=== Diagnostics ===
Used output buffers: 1 of 32 (9 max)
=== Platform ===
RepRapFirmware for Duet 2 WiFi/Ethernet version 1.21 running on Duet WiFi 1.02 or later
Board ID: 08DDM-9FAM2-LW4S4-6J1D8-3SD6R-T3SZX
Static ram used: 16152
Dynamic ram used: 100448
Recycled dynamic ram: 2184
Stack ram used: 3576 current, 4720 maximum
Never used ram: 7568
Last reset 01:20:22 ago, cause: reset button or watchdog
Last software reset time unknown, reason: User, spinning module GCodes, available RAM 7864 bytes (slot 3)
Software reset code 0x0003 HFSR 0x00000000, CFSR 0x00000000, ICSR 0x0441f000, BFAR 0xe000ed38, SP 0xffffffff
Error status: 0
Free file entries: 10
SD card 0 detected, interface speed: 20.0MBytes/sec
SD card longest block write time: 0.0ms
MCU temperature: min 31.9, current 32.0, max 32.5
Supply voltage: min 12.2, current 12.3, max 12.3, under voltage events: 0, over voltage events: 0
Driver 0: standstill, SG min/max not available
Driver 1: standstill, SG min/max not available
Driver 2: standstill, SG min/max not available
Driver 3: standstill, SG min/max not available
Driver 4: standstill, SG min/max not available
Date/time: 1970-01-01 00:00:00
Slowest main loop (seconds): 0.099909; fastest: 0.000050
=== Move ===
MaxReps: 0, StepErrors: 0, LaErrors: 0, FreeDm: 240, MinFreeDm 240, MaxWait: 0ms, Underruns: 0, 0
Scheduled moves: 0, completed moves: 0
Bed compensation in use: none
Bed probe heights: 0.000 0.000 0.000 0.000 0.000
=== Heat ===
Bed heaters = 0 -1 -1 -1, chamberHeaters = -1 -1
=== GCodes ===
Segments left: 0
Stack records: 1 allocated, 0 in use
Movement lock held by null
http is idle in state(s) 0
telnet is idle in state(s) 0
file is idle in state(s) 0
serial is ready with "M122" in state(s) 0
aux is idle in state(s) 0
daemon is idle in state(s) 0
queue is idle in state(s) 0
autopause is idle in state(s) 0
Code queue is empty.
=== Network ===
Responder states: HTTP(0) HTTP(0) HTTP(0) HTTP(0) FTP(0) Telnet(0) Telnet(0)
HTTP sessions: 0 of 8

• WiFi -
  Network state is starting
  WiFi module is disabled
  Failed messages: pending 0, notready 0, noresp 0
  Socket states: 0 0 0 0 0 0 0 0
  === Expansion ===

did as you asked
M997 reported successful upload.
M552 S0 does not respond

@dc42

config file contents

; Configuration file for Duet WiFi ver 1.

; General preferences

G90 ; Send absolute coordinates...
M83 ; ...but relative extruder moves
M555 P1 ; Set firmware to look like RepRapFirmare

; Network

M550 PCR10 ; Set machine name
M552 S1 ; Enable network
M587 S"PLUSNET-Q6QW" P"xxxxxxxx" ; access point

; Drives

M569 P0 S1 ; Drive 0 goes forwards
M569 P1 S1 ; Drive 1 goes forwards
M569 P2 S1 ; Drive 2 goes forwards
M569 P3 S1 ; Drive 3 goes forwards
M350 X16 Y16 Z16 E16 I1 ; Configure microstepping
M92 X80 Y80 Z4000 E420 ; Set steps per mm
M566 X900 Y900 Z12 E120 ; Set maximum speed changes
M203 X6000 Y6000 Z180 E1200 ; Set maximum speeds
M201 X500 Y20 Z250 E250 ; Set accelerations
M906 X800 Y800 Z800 E800 I30 ; Set motor currents (mA)
M84 S30 ; Set idle timeout

; Axis Limits

M208 X0 Y0 Z0 S1 ; Set axis minima
M208 X300 Y300 Z400 S0 ; Set axis maxima

; Endstops

M574 Y2 S1 ; Set active high endstops

; Z-Probe
M574 X1 Z1 S2 ; Set endstops controlled by probe
M558 P1 H5 F120 T6000 ; Set Z probe type to unmodulated and the dive height + speeds
G31 P500 X0 Y0 Z2.5 ; Set Z probe trigger value, offset and trigger height
M557 X45:275 Y45:275 S20 ; Define mesh grid

; Heaters
M305 P0 T100000 B4138 C0 R4700 ; Set thermistor + ADC parameters for heater 0
M143 H0 S120 ; Set temperature limit for heater 0 to 120C
M305 P1 T100000 B4138 C0 R4700 ; Set thermistor + ADC parameters for heater 1
M143 H1 S280 ; Set temperature limit for heater 1 to 280C

; Fans
M106 P0 S0.3 I0 F500 H-1 ; Set fan 0 value, PWM signal inversion and frequency. Thermostatic control is turned off
M106 P1 S1 I0 F500 H1 T45 ; Set fan 1 value, PWM signal inversion and frequency. Thermostatic control is turned on
M106 P2 S1 I0 F500 H1 T45 ; Set fan 2 value, PWM signal inversion and frequency. Thermostatic control is turned on

; Tools
M563 P0 D0 H1 ; Define tool 0
G10 P0 X0 Y0 Z0 ; Set tool 0 axis offsets
G10 P0 R0 S0 ; Set initial tool 0 active and standby temperatures to 0C

; Automatic power saving
M911 S10 R11 P"M913 X0 Y0 G91 M83 G1 Z3 E-5 F1000" ; Set voltage thresholds and actions to run on power loss

; Custom settings are not configured

; Miscellaneous
;M501 ; Load saved parameters from non-volatile memory

@ayudtee

sigh, im a dumbass, macro wasnt correct name, but, i corrected it and got it to run

hasnt changed anything though

@dc42

SENDING:M122
=== Diagnostics ===
Used output buffers: 1 of 32 (1 max)
=== Platform ===
RepRapFirmware for Duet 2 WiFi/Ethernet version 1.21 running on Duet WiFi 1.02 or later
Board ID: 08DDM-9FAM2-LW4S4-6J1D8-3SD6R-T3SZX
Static ram used: 16152
Dynamic ram used: 100448
Recycled dynamic ram: 2184
Stack ram used: 3576 current, 4528 maximum
Never used ram: 7760
Last reset 00:00:21 ago, cause: software
Last software reset time unknown, reason: User, spinning module GCodes, available RAM 7864 bytes (slot 3)
Software reset code 0x0003 HFSR 0x00000000, CFSR 0x00000000, ICSR 0x0441f000, BFAR 0xe000ed38, SP 0xffffffff
Error status: 0
Free file entries: 10
SD card 0 detected, interface speed: 20.0MBytes/sec
SD card longest block write time: 0.0ms
MCU temperature: min 31.6, current 31.9, max 32.0
Supply voltage: min 12.2, current 12.3, max 12.3, under voltage events: 0, over voltage events: 0
Driver 0: standstill, SG min/max not available
Driver 1: standstill, SG min/max not available
Driver 2: standstill, SG min/max not available
Driver 3: standstill, SG min/max not available
Driver 4: standstill, SG min/max not available
Date/time: 1970-01-01 00:00:00
Slowest main loop (seconds): 0.000259; fastest: 0.000049
=== Move ===
MaxReps: 0, StepErrors: 0, LaErrors: 0, FreeDm: 240, MinFreeDm 240, MaxWait: 0ms, Underruns: 0, 0
Scheduled moves: 0, completed moves: 0
Bed compensation in use: none
Bed probe heights: 0.000 0.000 0.000 0.000 0.000
=== Heat ===
Bed heaters = 0 -1 -1 -1, chamberHeaters = -1 -1
=== GCodes ===
Segments left: 0
Stack records: 1 allocated, 0 in use
Movement lock held by null
http is idle in state(s) 0
telnet is idle in state(s) 0
file is idle in state(s) 0
serial is ready with "M122" in state(s) 0
aux is idle in state(s) 0
daemon is idle in state(s) 0
queue is idle in state(s) 0
autopause is idle in state(s) 0
Code queue is empty.
=== Network ===
Responder states: HTTP(0) HTTP(0) HTTP(0) HTTP(0) FTP(0) Telnet(0) Telnet(0)
HTTP sessions: 0 of 8

• WiFi -
  Network state is starting
  WiFi module is disabled
  Failed messages: pending 0, notready 0, noresp 0
  Socket states: 0 0 0 0 0 0 0 0
  === Expansion ===

network state is starting
wifi module is disabled

hmmm, ive got a spare sd card somewhere, going to try reformatting it and starting fresh

@ayudtee it does exist there, i updated it in an external sd reader, reinstalled it in the duet board and tried running it.
came back
Warning: Macro file /macros/SetNetwork not found.

=== Diagnostics ===<LF>Used output buffers: 1 of 32 (1 max)<LF>=== Platform ===<LF>RepRapFirmware for Duet 2 WiFi/Ethernet version 1.21 running on Duet WiFi 1.02 or later<LF>Board ID: 08DDM-9FAM2-LW4S4-6J1D8-3SD6R-T3SZX<LF>Static ram used: 16152<LF>Dynamic ram used: 100248<LF>Recycled dynamic ram: 2384<LF>Stack ram used: 3576 current, 4528 maximum<LF>Never used ram: 7760<LF>Last reset 01:25:57 ago, cause: power up<LF>Last software reset time unknown, reason: User, spinning module GCodes, available RAM 7688 bytes (slot 2)<LF>Software reset code 0x0003 HFSR 0x00000000, CFSR 0x00000000, ICSR 0x0441f000, BFAR 0xe000ed38, SP 0xffffffff<LF>Error status: 0<LF>Free file entries: 10<LF>SD card 0 detected, interface speed: 20.0MBytes/sec<LF>SD card longest block write time: 0.0ms<LF>MCU temperature: min 28.8, current 30.8, max 31.4<LF>Supply voltage: min 12.2, current 12.2, max 12.3, under voltage events: 0, over voltage events: 0<LF>Driver 0: standstill, SG min/max not available<LF>Driver 1: standstill, SG min/max not available<LF>Driver 2: standstill, SG <Warning: Maximal number of bytes per line exceeded! Check the end-of-line settings or increase the limit in the advanced terminal settings.>

M587 with no pparameters returns
Error: M587: Failed to retrieve network list<LF>

M587 S"awesomewifi" P"dummypassword" returns failed to add SSID to remembered list

Long story ... just some background

Bought tevo little monster, bought duet wifi board, for a while life was good. had car accident, tlm too big now, am in chair, cant reach top of printer on work surface. or build surface if on floor.

bought Cr10, for a while life was really good, way better than the TLM. one day the cr10 extruder driver decided to stop working. thought stuff it and stick the duet wifi board in it, i want to go 2+ extruders soon anyway

got going wiring it in and when 3/4 way through i thought ive got enough done to start testing as i go

no such luck, i cannot get the blasted thing to connect via wifi. i reinstalled all the firmware files via duets webpage,

M115 command returns ''Duet 2 wifi / ethernet firmware version 1.21 duet wifi version 1.02 or later

i follow duets web page, getting connected, but the board doesnt seem to respond right.

M552 returns wifi module is being started
M587 returns failed to retrieve network list

im lost, need help, please, tearing my hair out and my 3d printing is the only thing keeping me sane

any advice welcome, even if ive screwed up, need to know where to move forward