Thank You for support, best wishes for future development, actually I'm also building cnc 3kw water, on duet family.
M115 B1
Duet EXP3HC rev 1.01 or earlier firmware version 3.4.4 (2022-10-14 11:45:56)
8.02.2023, 20:43:01 M122
=== Diagnostics ===
RepRapFirmware for Duet 3 MB6HC version 3.5beta2 (2023-02-08 17:43:01) running on Duet 3 MB6HC v1.01 (standalone mode)
Board ID: 08DJM-9P63L-DJ3S0-7J1DG-3SD6L-1VJM9
Used output buffers: 1 of 40 (30 max)
Error in macro line 22 while starting up: Response timeout: CAN addr 47, req type 6018, RID=0
=== RTOS ===
Static ram: 154344
Dynamic ram: 119016 of which 48 recycled
Never used RAM 69208, free system stack 202 words
Tasks: NETWORK(ready,17.1%,222) ETHERNET(notifyWait,0.2%,559) HEAT(notifyWait,0.0%,321) Move(notifyWait,0.0%,342) CanReceiv(notifyWait,0.0%,798) CanSender(notifyWait,0.0%,335) CanClock(delaying,0.0%,334) TMC(notifyWait,8.0%,90) MAIN(running,68.7%,446) IDLE(ready,5.9%,30), total 100.0%
Owned mutexes:
=== Platform ===
Last reset 00:01:37 ago, cause: power up
Last software reset at 2023-02-06 23:02, reason: User, Gcodes spinning, available RAM 91132, slot 2
Software reset code 0x0003 HFSR 0x00000000 CFSR 0x00000000 ICSR 0x00400000 BFAR 0x00000000 SP 0x00000000 Task MAIN Freestk 0 n/a
Error status: 0x00
Step timer max interval 132
MCU temperature: min 32.2, current 37.1, max 37.6
Supply voltage: min 23.9, current 24.0, max 24.0, under voltage events: 0, over voltage events: 0, power good: yes
12V rail voltage: min 12.1, current 12.1, max 12.2, under voltage events: 0
Heap OK, handles allocated/used 99/2, heap memory allocated/used/recyclable 2048/64/0, gc cycles 0
Events: 0 queued, 0 completed
Driver 0: standstill, SG min n/a, mspos 8, reads 17549, writes 14 timeouts 0
Driver 1: standstill, SG min n/a, mspos 16, reads 17546, writes 17 timeouts 0
Driver 2: standstill, SG min n/a, mspos 8, reads 17549, writes 14 timeouts 0
Driver 3: standstill, SG min n/a, mspos 8, reads 17549, writes 14 timeouts 0
Driver 4: standstill, SG min n/a, mspos 8, reads 17550, writes 14 timeouts 0
Driver 5: standstill, SG min n/a, mspos 8, reads 17550, writes 14 timeouts 0
Date/time: 2023-02-08 20:42:59
Slowest loop: 1000.06ms; fastest: 0.06ms
=== Storage ===
Free file entries: 20
SD card 0 detected, interface speed: 25.0MBytes/sec
SD card longest read time 1.2ms, write time 0.0ms, max retries 0
=== Move ===
DMs created 125, segments created 0, maxWait 0ms, bed compensation in use: none, comp offset 0.000
no step interrupt scheduled
=== DDARing 0 ===
Scheduled moves 0, completed 0, hiccups 0, stepErrors 0, LaErrors 0, Underruns [0, 0, 0], CDDA state -1
=== DDARing 1 ===
Scheduled moves 0, completed 0, hiccups 0, stepErrors 0, LaErrors 0, Underruns [0, 0, 0], CDDA state -1
=== Heat ===
Bed heaters 0 4 5 -1 -1 -1 -1 -1 -1 -1 -1 -1, chamber heaters -1 -1 -1 -1, ordering errs 0
Heater 1 is on, I-accum = 0.0
=== GCodes ===
Movement locks held by null, null
HTTP is idle in state(s) 0
Telnet is idle in state(s) 0
File is idle in state(s) 0
USB is idle in state(s) 0
Aux is idle in state(s) 0
Trigger is idle in state(s) 0
Queue is idle in state(s) 0
LCD is idle in state(s) 0
SBC is idle in state(s) 0
Daemon is idle in state(s) 0
Aux2 is idle in state(s) 0
Autopause is idle in state(s) 0
File2 is idle in state(s) 0
Queue2 is idle in state(s) 0
Q0 segments left 0, axes/extruders owned 0x80000003
Code queue 0 is empty
Q1 segments left 0, axes/extruders owned 0x0000000
Code queue 1 is empty
=== CAN ===
Messages queued 728, received 434, lost 0, boc 742
Longest wait 0ms for reply type 0, peak Tx sync delay 4, free buffers 50 (min 49), ts 488/93/0
Tx timeouts 0,0,99,0,0,18 last cancelled message type 30 dest 127
=== Network ===
Slowest loop: 8.37ms; fastest: 0.03ms
Responder states: MQTT(0) HTTP(0) HTTP(0) HTTP(0) HTTP(0) HTTP(0) HTTP(0) FTP(0) Telnet(0) Telnet(0)
HTTP sessions: 1 of 8
= Ethernet =
State: active
Error counts: 0 0 0 1 0 0
Socket states: 5 2 2 2 2 0 0 0
=== Multicast handler ===
Responder is inactive, messages received 0, responses 0
8.02.2023, 20:42:49 M952 B1
CAN bus speed 2000.0kbps, tseg1 0.75, jump width 0.17
8.02.2023, 20:42:46 M952 B0
8.02.2023, 20:42:42 M952 B0 S2000
8.02.2023, 20:42:35 M952 B1
8.02.2023, 20:42:26 M952 B0
CAN bus speed 1000.0kbps, tseg1 0.54, jump width 0.17
8.02.2023, 20:42:17 Failed to get file list
Directory 0:/macros/ not found
8.02.2023, 20:42:15 Failed to get file list
Directory 0:/macros not found
8.02.2023, 20:42:15 Connected to 192.168.137.120