Thank you guys! It finaly works! Nice Support!

Thank you guys! It finaly works! Nice Support!

@felek M122
=== Diagnostics ===
RepRapFirmware for Duet 3 MB6HC version 3.1.1 running on Duet 3 MB6HC v0.6 or 1.0 (SBC mode)
Board ID: 08DJM-956BA-NA3TN-6JTDG-3SD6K-TABQT
Used output buffers: 1 of 40 (10 max)
=== RTOS ===
Static ram: 154604
Dynamic ram: 162580 of which 56 recycled
Exception stack ram used: 224
Never used ram: 75752
Tasks: NETWORK(ready,1980) HEAT(blocked,1200) CanReceiv(suspended,3820) CanSender(suspended,1488) CanClock(blocked,1436) TMC(blocked,204) MAIN(running,4952) IDLE(ready,76)
Owned mutexes:
=== Platform ===
Last reset 00:00:56 ago, cause: power up
Last software reset at 2021-04-28 10:58, reason: User, spinning module LinuxInterface, available RAM 75212 bytes (slot 1)
Software reset code 0x0010 HFSR 0x00000000 CFSR 0x00000000 ICSR 0x0444a000 BFAR 0x00000000 SP 0xffffffff Task MAIN
Error status: 0
MCU temperature: min 22.7, current 26.2, max 26.2
Supply voltage: min 23.8, current 23.8, max 23.9, under voltage events: 0, over voltage events: 0, power good: yes
12V rail voltage: min 12.1, current 12.1, max 12.2, under voltage events: 0
Driver 0: standstill, reads 12480, writes 14 timeouts 0, SG min/max 0/0
Driver 1: standstill, reads 12480, writes 14 timeouts 0, SG min/max 0/0
Driver 2: standstill, reads 12481, writes 14 timeouts 0, SG min/max 0/0
Driver 3: standstill, reads 12481, writes 14 timeouts 0, SG min/max 0/0
Driver 4: standstill, reads 12485, writes 11 timeouts 0, SG min/max 0/0
Driver 5: standstill, reads 12485, writes 11 timeouts 0, SG min/max 0/0
Date/time: 2021-04-28 23:58:35
Slowest loop: 3.92ms; fastest: 0.14ms
=== Storage ===
Free file entries: 10
SD card 0 not detected, interface speed: 37.5MBytes/sec
SD card longest read time 0.0ms, write time 0.0ms, max retries 0
=== Move ===
Hiccups: 0(0), FreeDm: 375, MinFreeDm: 375, MaxWait: 0ms
Bed compensation in use: none, comp offset 0.000
=== MainDDARing ===
Scheduled moves: 0, completed moves: 0, StepErrors: 0, LaErrors: 0, Underruns: 0, 0 CDDA state: -1
=== AuxDDARing ===
Scheduled moves: 0, completed moves: 0, StepErrors: 0, LaErrors: 0, Underruns: 0, 0 CDDA state: -1
=== Heat ===
Bed heaters = 0 -1 -1 -1 -1 -1 -1 -1 -1 -1 -1 -1, chamberHeaters = -1 -1 -1 -1
=== GCodes ===
Segments left: 0
Movement lock held by null
HTTP* is ready with "M122" in state(s) 0
Telnet is idle in state(s) 0
File is idle in state(s) 0
USB is idle in state(s) 0
Aux is idle in state(s) 0
Trigger* is idle in state(s) 0 0, running macro
Queue is idle in state(s) 0
LCD is idle in state(s) 0
SBC is idle in state(s) 0
Daemon* is idle in state(s) 0
Aux2 is idle in state(s) 0
Autopause is idle in state(s) 0
Code queue is empty.
=== Network ===
Slowest loop: 1.45ms; fastest: 0.01ms
Responder states: HTTP(0) HTTP(0) HTTP(0) HTTP(0) HTTP(0) HTTP(0) FTP(0) Telnet(0), 0 sessions Telnet(0), 0 sessions
HTTP sessions: 0 of 8

• Ethernet -
  State: disabled
  Error counts: 0 0 0 0 0
  Socket states: 0 0 0 0 0 0 0 0
  === CAN ===
  Messages sent 129, longest wait 0ms for type 0
  === Linux interface ===
  State: 0, failed transfers: 1
  Last transfer: 16ms ago
  RX/TX seq numbers: 1340/1341
  SPI underruns 1, overruns 1
  Number of disconnects: 0
  Buffer RX/TX: 0/0-0
  === Duet Control Server ===
  Duet Control Server v3.2.2
  Trigger:
  Buffered code: M501 ; load saved parameters from non-volatile memory
  ==> 24 bytes
  Executing macro config.g, started by system

Next stack level
Pending code: M905 P"2021-04-29" S"00:00:12"
Code buffer space: 4096
Configured SPI speed: 8000000 Hz
Full transfers per second: 9.94
Maximum length of RX/TX data transfers: 3168/728

@robbe21 I didnt tried to replace the Endstop, i think the Endstop works, because when i home Y-Axis before the X-Axis it works.

@felek

If i execute the M122 Command in the Console this happens:

I lost the connection to the Duet Webcontrol and the DIAG LED on the Duet was permanetly blinking.

@felek Nope there is nothing. Just when i power it up the Status in the Webinterface is busy.

@felek Oh i forgot that!:D

homeall.g
config.g
homez.g
homey.g
homex.g

Hello guys! I have a Problem with my Printer, when i home the X-Axis it works fine, after it i home Y-Axis and it cant stop homing, it like an endless loop.

Same Problem in reverse Order!

I dont know what i´ve done wrong:/

Video

Thanks!