Posts made by Tisum1979

ok so I created a access point which isn't connected to the internet however I typed in my IP address and the control board popped up and the blue light is on to my wifi but I can not get my WCB to connect

Can I upgrade firmware from 2.05.1 / wifi firmware version 1.23 if I can not get onto my WCB?

Hey this is what things say as of now for my Duet2 wifi-WiFi module is trying to connect<LF>
Failed messages: pending 0, notready 0, noresp 0<LF>
WiFi firmware version 1.23<LF>
WiFi MAC address 98:f4:ab:cf:be:21<LF>
WiFi Vcc 3.33, reset reason Turned on by main processor<LF>
WiFi flash size 4194304, free heap 28112<LF>
Socket states: 0 0 0 0 0 0 0 0<LF>
ok<LF>
M587<LF>
Remembered networks:<LF>
MySpectrumWiFiF8-2G IP=192.168.1.1 GW=0.0.0.0 NM=0.0.0.0<LF>
ok<LF>
WiFi reported error: Failed while trying to connect to MySpectrumWiFiF8-2G<LF>
WiFi module is idle<LF>
WiFi reported error: Failed while trying to connect to MySpectrumWiFiF8-2G<LF>
WiFi module is idle<LF>
WiFi reported error: Failed while trying to connect to MySpectrumWiFiF8-2G<LF>
WiFi module is idle<LF>

on my duet2 board the 3.3v light is red not green

Is that normal for Wifi vcc 3.33, reset reason turned on by main processor

not sure how to get to text editor.

ok so I just talked to the service provider and there are no security that would prevent the board from connecting. The only other thing I can think is that I need to use macro to enter the SSID and password. I'm not sure what I gotta do to do that

RepRapFirmware for Duet 2 WiFi/Ethernet Version 2.05.1 dated 2020-02-09b1<LF>
<LF>
Executing config.g...HTTP is enabled on port 80<LF>
FTP is disabled<LF>
TELNET is disabled<LF>
Done!<LF>

I noticed in the feed back from the board that it says talnet disabled. what does that mean

@dc42 Ok, so I did a test and made a dummy wifi account or link and was able to connect my board to the dummy wifi, which the wifi light stayed solid but it disconnected my internet. I connected to my internet and the light stayed solid blue but I could not get an IP address to pop up. I even typed in the wifi IP address to see if the DWC would pop up but it didn't. I am thinking there is a disconnect because of the providers security or mine.

I do understand what you are saying but stumped on why the connection isn't working

I have 2 separate names for the 2 and 5 and I am on 2

I am thinking the security from spectrum is keeping me from connecting the way it normally does

ok so I will try to clear all network and reenter ssid and password along with the IP adress and see what happens

ok so I need to be set to the IP address or the DNS address
That could be the issue

• WiFi -<LF>
  Network state is running<LF>
  WiFi module is providing access point <LF>
  Failed messages: pending 0, notready 0, noresp 1<LF>
  WiFi firmware version 1.23<LF>
  WiFi MAC address 9a:f4:ab:cf:be:21<LF>
  WiFi Vcc 3.33, reset reason Exception<LF>
  WiFi flash size 4194304, free heap 25848<LF>
  WiFi IP address 192.168.1.1<LF>
  Connected clients 0<LF>
  Socket states: 0 0 0 0 0 0 0 0<LF>
  ok<LF>

so if I am connected to the duet wifi I don't have internet. It disconnects me from spectrum

would the connection to the board not work if there

ok the blue light came on but it was asking for a network security key.

M552 S2<LF>
ok<LF>
WiFi module is providing access point DuetWiFi, IP address 192.168.1.1<LF>
WiFi module is providing access point DuetWiFi, IP address 192.168.1.1<LF>