Cannot connect to DWC Simple fix??
-
I found this post from
dc42 ADMINISTRATORS 8 Mar 2018, 12:54
Either:- Send M552 S0, then send M552 P192.168.1.xx, then send M552 S1. You should then be able to connect DWC. In DWC go to the System editor and edit the M552 command in config.g to have that IP address.
Or:
- Move the SD card to a PC and use a text editor to make the same change to the M552 command in config.g.
So I was able to get connected to the DWC again, I just don't know if I turn this off if it will reconnect.
We shall see. The IP recorded in the config.g was different than the IP that came up when entering the
M552 command.Do I always have to go thru YAT to get to DWC or should it come up when the Duet is powered on??
-
Hi,
Read about M552 a little more closely.
Notice:
"On the Duet 2 WiFi running firmware 1.19 and later, the IP address is set in the M587 command when you configure the access point details."
Once you get the WiFi configured correctly it is saved in the WiFi hardware "flash" memory and you can connect any time you power/reset the Duet.
Frederick
-
@fcwilt Concerning YAT not connecting, what was described above is what happened to me. I opened a second instance of YAT and got connection errors. I also closed all connections and had some issues connecting back again.
-
I am having this same issue:
Duet 2 WIFI running 2.03 suite of firmware and drivers from github
Made it through Step 8 in the "Getting Connected to your Duet" guide
Connection to YAT works great
Connection to Pronterface works great
M552 returns:
ok
WiFi module is connected to access point SkyNet Guest, IP address 192.168.0.192
My tp-link router shows a wireless client at the 192.168.0.192 address but cannot identify it. (shows a "*" )I am clearly set up and connected, but I get the "can't reach this page" error every time. (I've tried both the IP address and the duettest.local routes)
-
@spudaddict said in Cannot connect to DWC Simple fix??:
WiFi module is connected to access point SkyNet Guest, IP address 192.168.0.192
The "Guest" part suggests to me that it is configured for client isolation. Which means a WiFi device connected using that SSID can see the Internet but nothing else on the local network. And nothing else on the local network can see the device.
Frederick
-
@spudaddict said in Cannot connect to DWC Simple fix??:
WiFi module is connected to access point SkyNet Guest, IP address 192.168.0.192
Can you ping 192.168.0.192 from the PC where you are attempting to connect a browser?
-
You could try setting the Duet WiFi up in access point mode to check that it's definitely your network. I agree through it sounds like the Guest segment of your network could be restricting access.
-
Thanks to all that helped get us connected. Configuring the access was the final answer to
getting connected. Now I can turn on the Duet board and it will find our wifi.
Now on to the next hurdle, to actually configure the setting to this printer.
When I re-load the config.g to the board with the new setting will this stage of connection be lost.Maybe this should go to a new discussion.
I have hard wired all the motors, five in all two extruder motors. Optical limit switches and heaters ect.
I also have a Panel Duet 5i. I get no response from the panel, but I guess that is because I have not configured
and uploaded the new parameters. Still new to setting this up so should the old Config.g file be saved before
loading a new one? Does any on have a config file for a JGAurora A8 printer?Mark
-
@AMPMAKER said in Cannot connect to DWC Simple fix??:
Configuring the access was the final answer to getting connected.
Hi,
What exactly do you mean by that?
Thanks.
Frederick
-
@AMPMAKER said in Cannot connect to DWC Simple fix??:
Send M552 S0, then send M552 P192.168.1.xx, then send M552 S1. You should then be able to connect DWC. In DWC go to the System editor and edit the M552 command in config.g to have that IP address.
Send M552 S0, then send M552 P192.168.1.xx, then send M552 S1. You should then be able to connect DWC. In DWC go to the System editor and edit the M552 command in config.g to have that IP address.
Maybe the lingo was not correct..sorry
