Mapping Endstops

Lukrative

@Danal So assuming I wired two NC endstops in series, my config file would look something like this?

M584 U6 ; use drive 6 for the U axis
M574 U1 S1 ; U axis endstop on low end, active high

What about if I wanted to use two separate limit switches? Would this work?

M584 U6 V6
M574 U1 V2 S1

Then I could create homing files for the U and V axes, where "home U" is move to the low end and "home V" is move to the high end. Then I could put in an if statement (in the homeu.g file) where while homing U, it will back off of the endstop if it's already triggered, but not if it's already away from it.

Is there any reason this wouldn't work?

Danal

That would probably work, but there is no need for V.

U can have a high and a low homing switch.

Probe with H1 when near the low. Edit: "when trying to find" is probably better phrase than "near"

Probe with H3 when near the high. Edit: Ditto

Danal

M574 U1 S1
M574 U2 S1

Lukrative

@Danal

Lovely! Thanks for the reply.

dc42

@Danal said in Mapping Endstops:

M574 U1 S1
M574 U2 S1

That's not supported (yet). The second command will override the first.

Danal

Oh drat. @dc42, Thanks for the clarification!

@Lukrative then wire two NC switches in series, and you can still use H1, with appropriate numeric coordinates to find hi or lo.

I know this works, because the U axis for my toolchanger is wired and configured this way.

Danal

To expand on that:

Homing U uses a microswitch in a very conventional fashion. Homing unlocks a tool.

The second switch, wired in series with the first, is between two disks with a spring arrangement such that when locking a tool, the lock reaches a certain amount of torque and the spring stretches and the disks move in relation to each other, thus opening the second switch.

This forms a "torque sensor" so the lock is moved to a specific torque (not a specific position) when locking a tool.

Tool Unlock Macro. Moving the same direction that homing moves, that is, toward 0 (rotation), in this case via negative numbers because we want a relative move. Note the H1.

G91                 ; Set relative movements
G1 U-4 F9000 H2     ; Back off the limit switch with a small move
G1 U-360 F9000 H1   ; Perform up to one rotation looking for the home limit switch
G90                 ; Restore absolute movements

Tool lock macro. Note the H1, even though we are now rotating positive it is still H1, not H3. Only one (logical) switch... that is really two physical, one at 'each end'.

; Engage the toolchanger lock

G91                 ; Set relative mode
G1 U10 F9000 H0      ; Back off the limit switch with a small move
G1 U360 F9000 H1    ; Perform up to one rotation looking for the torque limit switch
G90                 ; Set absolute mode

This all applies directly to your linear axis. Two switches, series wired, always probe with H1, relative moves set positive/negative for the appropriate end.

Make sense?

Lukrative

@Danal It's good to know that wiring in series is an option, but I want my tool change macros to work even if somehow the filament changer is out of alignment or if I'm just starting the machine. For example, suppose I call tool 0, which is on the left side of my printer. If the filament changer is already at the left endstop, I want it to move off the endstop to the right first, then go back to the endstop. If it's sitting at the right endstop, I would like it to just move to the left endstop without moving to the right first. As far as I understand, RRF3 allows you to do this with conditional statements. But if both endstops are wired in series, there's no way of knowing which of these options to choose without prior information.

@dc42 is this a viable method of tricking the firmware into having min and max endstops?

M584 U6 V6
M574 U1 V2 S1

jay_s_uk

I remap my endstops within my tool locking and unlocking macros.

; Engage the toolchanger lock

M400                    ; Make sure everything has stopped before we make changes

; ################## Prepare Axis #########################
M584 P4			; Unhides U axis

; ################## Endstop Mapping ######################
M574 U2 S3        				; set U axis (tool changer) maxima to use motor stall

;################### Stall Detection ######################

M915 U S3 F0 H20 R4700				; Coupler

;################### Locking Procedure ####################
G91                     ; Use relative positioning
G1 H1 U180 F5000 	; Move all carriages up 700mm, stopping at the endstops
G90                     ; Back to absolute positioning

; ################## Reset System #########################
M584 P3			; Hides U axis

; Unlock the toolchanger lock

M400                    ; Make sure everything has stopped before we make changes

; ################## Prepare Axis #########################
M584 P4			; Unhides U axis

; ################## Endstop Mapping ######################
M574 U1 S1 P"io3.in"                    	; configure active-high endstop for low end on U via pin io3.in

;################### Locking Procedure ####################
G91                     ; Use relative positioning
G1 H1 U-90 F5000 	; Move all carriages up 700mm, stopping at the endstops
G1 H1 U5 F5000
G90                     ; Back to absolute positioning

; ################## Reset System #########################
M584 P3			; Hides U axis

Danal

No problem... at startup, home, just like any other axis. I can't overstress that I'm doing EXACTLY what you are doing, just in a circle instead of a line. It all works. No jams, no funny startups. G28 and/or G28 U work normally. etc, etc, etc.

Do include homeu.g in homeall.g

homeu.g

G91                     ; Set relative mode
G1 U-360 F9000 H1       ; Big negative move to search for home endstop
G1 U6 F600              ; Back off the endstop
G1 U-10 F600 H1         ; Find endstop again slowly
G90                     ; Set absolute mode

Jay is remapping so he can use stall detect. Which also works great, after you tune it. (Jay and I talk a lot on the Jubilee discord).