Unable to send any files to my Duet Wifi

jay_s_uk

I would guess your SD card is borked.
Try a new one

dc42

What is the reported WiFi signal strength in the M122 report?

ElmoC

@jay_s_uk Tried a new card. Same issue.

ElmoC

This post is deleted!

ElmoC

@dc42 When I was able to connect, it was -67 I believe. Since that message, things have gotten worse. I tried updating via Ponterface and it reports it can't write to the printer. The PanelDue still works and I can transfer files by writing directly to the card so I have been able to print. Going to try reflashing the board in a bit.

ElmoC

@dc42 When trying to update via USB through Ponterface, I get this...

Connecting...
RepRapFirmware for Duet 2 WiFi/Ethernet Version 2.05 dated 2019-12-13b1
Executing config.g...FTP is enabled on port 21
TELNET is enabled on port 23
Warning: Heater 0 appears to be over-powered. If left on at full power, its temperature is predicted to reach 265C.
Done!
Printer is now online.
>>>M115
SENDING:M115
FIRMWARE_NAME: RepRapFirmware for Duet 2 WiFi/Ethernet FIRMWARE_VERSION: 2.05 ELECTRONICS: Duet WiFi 1.02 or later + DueX5 FIRMWARE_DATE: 2019-12-13b1
>>>M997 S0
SENDING:M997 S0
[ERROR] Can't read from printer (disconnected?) (SerialException): call to ClearCommError failed
[ERROR] Can't write to printer (disconnected?) (SerialException): WriteFile failed ([Error 22] The device does not recognize the command.)
[ERROR] Can't write to printer (disconnected?) (SerialException): WriteFile failed ([Error 22] The device does not recognize the command.)
[ERROR] Can't write to printer (disconnected?) (SerialException): WriteFile failed ([Error 22] The device does not recognize the command.)
[ERROR] Can't write to printer (disconnected?) (SerialException): WriteFile failed ([Error 22] The device does not recognize the command.)
[ERROR] Disconnecting after 4 failed writes.
Disconnected.

jay_s_uk

@ElmoC
Have you got it in marlin emulation mode?
See https://duet3d.dozuki.com/Wiki/Gcode#Section_M555_Set_compatibility

ElmoC

@jay_s_uk As far as I know I don't. It had been working fine but then problems started without making any changes to the config.g file. Next time I have the card out, I will check to be sure.

UPDATE: I checked and it is set to make the OUTPUT look like Marlin, which it has always been set to. Nothing about emulation of Marlin.

ElmoC

So after flashing the firmware via BOSSA and updated the WiFi firmware via the PanelDue. Rebuilt the /www directory (note, the DuetWebControl.bin file is not in the release file), I was able to get the web interface back up. Need to try and send a file to it next.

UPDATE: When I try testing the connection for PrusaSlicer, the web interface gets knocked off (Failed to maintain connection) and asks for the password. PrusaSlicer reports the test was successful.

UPDATE 2: Still unable to upload files. Going to try to put a different AP on for the printer to use.

ElmoC

Adding a different access point allowed me to send a job from PrusaSlicer. Will have to see how long this will work.

ElmoC

And I can't upload again.

FTP also fails.

droftarts

@ElmoC Have you tried running the Duet in Access Point mode? Not as convenient as connecting it to your network, but might show if the issue is with the Duet or your network. See https://duet3d.dozuki.com/Wiki/Gcode#Section_M589_Configure_access_point_parameters

Ian

ElmoC

This post is deleted!