CR10 S5 upgrade to Duet 2 Wifi

GT1Za

@NexxCat that worked, I took it up to S80 for a 6x6 mesh. Ill experiment later to find the right values.

Now the if I run the Auto Bed Compensation, its starts, but the BL touch probe doesnt deploy?

NexxCat

@GT1Za
Do you have deployprobe.g and retractprobe.g files? If so, what are the contents of each?

GT1Za

@NexxCat

; deployprobe.g
; called to deploy a physical Z probe
M280 P64 S10 ; deploy BLTouch

; retractprobe.g
; called to retract a physical Z probe
M280 P64 S90 ; retract BLTouch

NexxCat

@GT1Za
In config.g, change:

M307 H64 A-1 C-1 D-1 ; disable heater on PWM channel for BLTouch

to

M307 H3 A-1 C-1 D-1 ; disable heater on PWM channel for BLTouch

and in both deployprobe.g and retractprobe.g, change the P64 to P3. Then try

GT1Za

Nope.. Still says Z probe was not triggered during move.

NexxCat

@GT1Za
Does it deploy now though? From the photos it looks to be wired into pin 8 of the expansion connector, which is Heater 3. Your config had it looking on Heater 64, hence the change.

NexxCat

@GT1Za
Just noticed something else also. You have the original Z endstop plugged in and configured. I don't as the BLTouch does all Z homing. Try the following changes in config.g:

M574 X1 Y1 Z1 S1 ; set active high endstops

to

M574 X1 Y1 S1 ; set active high endstops

Add:

M574 Z1 S2                              ; Set Z endstop controlled by probe

GT1Za

@NexxCat

Ill try it now. Ive always liked the idea of keeping the z stop incase the BLtouch fails. Is there no way to keep both?

NexxCat

@GT1Za
I have no experience with that I'm afraid, so I can't help, but people here are really friendly and knowledgeable, so someone else may know

GT1Za

ok, Z probe still didnt deploy when trying to home the Z. I had to hit the stop button.

NexxCat

@GT1Za
Just to double check. The brown wire from the BLTouch is definitely plugged into Pin 8 of the expansion connector?

GT1Za

definitely into pin 8
GPIO pins.jpg

NexxCat

@GT1Za
DOH! I know what I missed.

In both deployprobe.g and retractprobe.g, add I1 to the end of the parameters:

deployprobe.g
M280 P3 S10 I1

retractprobe.g
M280 P3 S90 I1

GT1Za

@NexxCat
I have just checked the wiring diagram:
Pin 1: To Red
Pin 2: To Blue/Brown
Pin 8: To Orange/Yellow

This is as per: https://duet3d.dozuki.com/Wiki/Connecting_a_Z_probe

This is how I have it wired

I have added the I1 to both, but still not deploying

NB: This is not deploying on HOMING the Z as I cant run the mesh bed before homing.

NexxCat

@GT1Za
Hmm, and you still have the config.g M307 set to H3?

Looks like the BLTouch isn't receiving the servo signal. The "I" parameter in the deploy and retract is needed because we're wired directly into the expansion connector, if you had a Duex, it wouldn't be required, but with the correct heater configured (heater 3), and the inversion, it should work $:\$

Edit: Can you post your homez.g and homeall.g please?

GT1Za

in the config.g:

; homeall.g
; called to home all axes
;
; generated by RepRapFirmware Configuration Tool v2.1.8 on Fri Mar 20 2020 11:57:17 GMT+0200 (South Africa Standard Time)
G91 ; relative positioning
G1 H2 Z5 F6000 ; lift Z relative to current position
G1 H1 X-515 Y-515 F3000 ; move quickly to X and Y axis endstops and stop there (first pass)
G1 H2 X5 Y5 F6000 ; go back a few mm
G1 H1 X-515 Y-515 F240 ; move slowly to X and Y axis endstops once more (second pass)
G1 H1 Z-505 F240 ; move Z down stopping at the endstop
G90 ; absolute positioning
G92 Z0 ; set Z position to axis minimum (you may want to adjust this)

; Uncomment the following lines to lift Z after probing
;G91 ; relative positioning
;G1 Z5 F100 ; lift Z relative to current position
;G90 ; absolute positioning

; homez.g
; called to home the Z axis
;
; generated by RepRapFirmware Configuration Tool v2.1.8 on Fri Mar 20 2020 11:57:18 GMT+0200 (South Africa Standard Time)
G91 ; relative positioning
G1 H2 Z5 F6000 ; lift Z relative to current position
G1 H1 Z-505 F3000 ; move Z down until the endstop is triggered
G92 Z0 ; set Z position to axis minimum (you may want to adjust this)

; Uncomment the following lines to lift Z after probing
;G91 ; relative positioning
;G1 Z5 F100 ; lift Z relative to current position
;G90 ; absolute positioning

NexxCat

@GT1Za
Ok, the home macros aren't configured for a z-probe. Here are mine:

; homez.g
; called to home the Z axis
;
M290 R0 S0	; Reset babystepping
G91             ; relative positioning
G1 Z5 F6000 S2  ; lift Z relative to current position
G90             ; absolute positioning
G1 X118 Y148 F6000      ; go to the bed centre and home Z
G30             ; home Z by probing the bed

; homeall.g
; called to home all axes
;
M290 R0 S0		; Reset babystepping
G91                     ; relative positioning
G1 Z5 F6000 S2          ; lift Z relative to current position
G1 S1 X-305 Y-305 F3600 ; move quickly to X and Y axis endstops and stop there (first pass)
G1 X5 Y5 F6000          ; go back a few mm
G1 S1 X-305 Y-305 F360  ; move slowly to X and Y axis endstops once more (second pass)
G90                     ; absolute positioning
M98 Pdeployprobe.g      ; deploy mechanical Z probe
G1 X118 Y148 F6000      ; go to the bed centre and home Z
G30                     ; home Z by probing the bed
M98 Pretractprobe.g     ; retract mechanical Z probe

You'll need to adjust X and Y in both for your printer because you are 500x500.

GT1Za

wow ok a whole new issue

in homez.g
G1 X118 Y148 F6000 ; go to the bed centre and home Z

I changed to:
G1 X250 Y250 F6000 ; go to the bed centre and home Z

this should be the center of the bed. but it tried to send it way off and I had to hit stop.

The Y steps dont seem to be right as 150 is taking me just short of center. 250 basically made it travel off and I had to hit stop.
The good news is the probe worked!

NexxCat

@GT1Za
Did you also adjust:

G1 S1 X-305 Y-305 F3600

to

G1 S1 X-515 Y-515 F3600

and

G1 S1 X-305 Y-305 F360

to

G1 S1 X-515 Y-515 F360

GT1Za

Yes I did.
The Y is just going too far. Everything else is as its meant to be