Duet3D Logo Duet3D
    • Tags
    • Documentation
    • Order
    • Register
    • Login

    I need help with upgrading firmware on Duet 3 + SBC

    Scheduled Pinned Locked Moved
    Firmware installation
    5
    21
    872
    Loading More Posts
    • Oldest to Newest
    • Newest to Oldest
    • Most Votes
    Reply
    • Reply as topic
    Log in to reply
    This topic has been deleted. Only users with topic management privileges can see it.
    • jmjcokeundefined
      jmjcoke
      last edited by

      Hi Danal,

      Yes I did cycle power and tried the other suggestion you made in another thread.

      I just noticed the = in this statement so i will try it with =1.3.0.0
      sudo apt install duetsoftwareframework=1.2.4.0

      Joshua Coke

      Trick Laser Metal Max with Smart Effector
      Duet Wifi
      Zesty Nimble
      Mosaic Pallette+
      At work
      Renishaw AM250/400/ RenAM500M/500Q Powder Bed Fusion (Metal 3D Printers)

      dc42undefined 1 Reply Last reply Reply Quote 0
      • dc42undefined
        dc42 administrators @jmjcoke
        last edited by

        @jmjcoke said in I need help with upgrading firmware on Duet 3 + SBC:

        I just noticed the = in this statement so i will try it with =1.3.0.0

        1.3.1 is now available.

        Duet WiFi hardware designer and firmware engineer
        Please do not ask me for Duet support via PM or email, use the forum
        http://www.escher3d.com, https://miscsolutions.wordpress.com

        jmjcokeundefined 1 Reply Last reply Reply Quote 0
        • jmjcokeundefined
          jmjcoke @dc42
          last edited by

          @dc42 I am stuck with the Drive not mounted with 1.3.1.

          Joshua Coke

          Trick Laser Metal Max with Smart Effector
          Duet Wifi
          Zesty Nimble
          Mosaic Pallette+
          At work
          Renishaw AM250/400/ RenAM500M/500Q Powder Bed Fusion (Metal 3D Printers)

          1 Reply Last reply Reply Quote 0
          • jmjcokeundefined
            jmjcoke
            last edited by

            I give up. I am removing the toolboards and the tool distro board I installed and rewiring everything back. from the main board.

            Joshua Coke

            Trick Laser Metal Max with Smart Effector
            Duet Wifi
            Zesty Nimble
            Mosaic Pallette+
            At work
            Renishaw AM250/400/ RenAM500M/500Q Powder Bed Fusion (Metal 3D Printers)

            1 Reply Last reply Reply Quote 0
            • ChrisPundefined
              ChrisP
              last edited by

              How come? Can you not just drop back to a previous version (1.2.5.0?) ? Tool boards work fine with this and everything pretty stable before 1.3.0.

              1 Reply Last reply Reply Quote 0
              • jmjcokeundefined
                jmjcoke
                last edited by

                Please tell me how to install 1.2.5.0.

                Joshua Coke

                Trick Laser Metal Max with Smart Effector
                Duet Wifi
                Zesty Nimble
                Mosaic Pallette+
                At work
                Renishaw AM250/400/ RenAM500M/500Q Powder Bed Fusion (Metal 3D Printers)

                1 Reply Last reply Reply Quote 0
                • ChrisPundefined
                  ChrisP
                  last edited by ChrisP

                  Erm, there might be easier / quicker ways from those who know Linux better than me, but I'd firstly backup the SD. Then uninstall what you have using something likesudo apt remove duetsoftwareframework, then I'd do an autoremove to make sure the dependencies are uninstalled too sudo apt autoremove. Finally install the specific version you want sudo apt install duestsoftwareframwork=1.2.5.0, or whatever version you want. Then restore you SD card backup.

                  You can see what versions are available using sudo apt list -a duetsoftwareframework.

                  (I take no responsibility if it all goes south, btw 😛 )

                  1 Reply Last reply Reply Quote 0
                  • A Former User?
                    A Former User
                    last edited by

                    I found I had to specify all the versions for all the dependencies, but should work (although i only tested apt, not with dsf/dwc)

                    @bearer said in RepRapFirmware 3.01-RC6 released:

                    maybe this works better, specifying all the packages to fulfill dependencies for duetsoftwareframework=1.2.5.0

                    sudo apt install  duetcontrolserver=1.2.5.0 duetsd=1.0.5 duettools=1.2.5.0 duetwebserver=1.2.3.1 duetwebcontrol=2.0.7-1 reprapfirmware=1.2.5.0-1 duetruntime=1.2.5.0 duetsoftwareframework=1.2.5.0
                    
                    ChrisPundefined 1 Reply Last reply Reply Quote 0
                    • ChrisPundefined
                      ChrisP @A Former User
                      last edited by

                      @bearer said in I need help with upgrading firmware on Duet 3 + SBC:

                      I found I had to specify all the versions for all the dependencies, but should work (although i only tested apt, not with dsf/dwc)

                      @bearer said in RepRapFirmware 3.01-RC6 released:

                      maybe this works better, specifying all the packages to fulfill dependencies for duetsoftwareframework=1.2.5.0

                      sudo apt install  duetcontrolserver=1.2.5.0 duetsd=1.0.5 duettools=1.2.5.0 duetwebserver=1.2.3.1 duetwebcontrol=2.0.7-1 reprapfirmware=1.2.5.0-1 duetruntime=1.2.5.0 duetsoftwareframework=1.2.5.0
                      

                      I hadn't actually tried, so this is very likely - good catch. That said, I think it'll usually tell you what dependency versions are expected when you try the install. But this^^ will do it nicely in one hit assuming the version #s are correct.

                      1 Reply Last reply Reply Quote 0
                      • jmjcokeundefined
                        jmjcoke
                        last edited by

                        Thank you @bearer and @ChrisP, I continue trying to get this going. I am also crimping JST ZH sockets for the first time and that may have add to my frustration level.

                        Joshua Coke

                        Trick Laser Metal Max with Smart Effector
                        Duet Wifi
                        Zesty Nimble
                        Mosaic Pallette+
                        At work
                        Renishaw AM250/400/ RenAM500M/500Q Powder Bed Fusion (Metal 3D Printers)

                        ChrisPundefined 1 Reply Last reply Reply Quote 0
                        • ChrisPundefined
                          ChrisP @jmjcoke
                          last edited by

                          @jmjcoke said in I need help with upgrading firmware on Duet 3 + SBC:

                          Thank you @bearer and @ChrisP, I continue trying to get this going. I am also crimping JST ZH sockets for the first time and that may have add to my frustration level.

                          Yeh, crimping is rarely fun. Have you got an Engineer PA-21 for those pins? It's not exactly cheap, but I felt the cost was worth saving the frustration! 😄

                          A Former User? 1 Reply Last reply Reply Quote 0
                          • A Former User?
                            A Former User @ChrisP
                            last edited by A Former User

                            @ChrisP said in I need help with upgrading firmware on Duet 3 + SBC:

                            Engineer PA-21

                            thats a wee bit too large for the JST ZH on the tool board, but good for the VH series used on the motors and heaters.
                            (the engineer 09 or iwis 2820m is okay for ZH)

                            ChrisPundefined jmjcokeundefined 2 Replies Last reply Reply Quote 0
                            • ChrisPundefined
                              ChrisP @A Former User
                              last edited by

                              @bearer said in I need help with upgrading firmware on Duet 3 + SBC:

                              @ChrisP said in I need help with upgrading firmware on Duet 3 + SBC:

                              Engineer PA-21

                              thats a wee bit too large for the JST ZH on the tool board, but good for the VH series used on the motors and heaters.
                              (the engineer 09 or iwis 2820m is okay for ZH)

                              Gosh! Yeh! Didn't realise those were the tool board ones. As you said, I was thinking of the VH. We just bought the connector pack, so didn't have to deal with the tiny crimps!
                              Good luck with those 👍

                              1 Reply Last reply Reply Quote 0
                              • jmjcokeundefined
                                jmjcoke @A Former User
                                last edited by

                                @bearer I am using engineer No.11. 0.7-2.2. I will look into the crimpers you suggest.

                                Joshua Coke

                                Trick Laser Metal Max with Smart Effector
                                Duet Wifi
                                Zesty Nimble
                                Mosaic Pallette+
                                At work
                                Renishaw AM250/400/ RenAM500M/500Q Powder Bed Fusion (Metal 3D Printers)

                                A Former User? 1 Reply Last reply Reply Quote 0
                                • A Former User?
                                  A Former User @jmjcoke
                                  last edited by

                                  @jmjcoke said in I need help with upgrading firmware on Duet 3 + SBC:

                                  I am using engineer No.11. 0.7-2.2.

                                  enginner docs says to use the 1.0 die, so you should be covered?

                                  1 Reply Last reply Reply Quote 0
                                  • jmjcokeundefined
                                    jmjcoke
                                    last edited by

                                    Yes, I crimp with the 1.3 first then lightly use the 1.0 so that it fits into the slot of the plug. The crimp on the insulation is the most challenging.

                                    Joshua Coke

                                    Trick Laser Metal Max with Smart Effector
                                    Duet Wifi
                                    Zesty Nimble
                                    Mosaic Pallette+
                                    At work
                                    Renishaw AM250/400/ RenAM500M/500Q Powder Bed Fusion (Metal 3D Printers)

                                    1 Reply Last reply Reply Quote 0
                                    • A Former User?
                                      A Former User
                                      last edited by

                                      Maybe you're using too thick a wire?

                                      1 Reply Last reply Reply Quote 0
                                      • jmjcokeundefined
                                        jmjcoke
                                        last edited by

                                        plug.jpg

                                        Might be alittle big.

                                        Joshua Coke

                                        Trick Laser Metal Max with Smart Effector
                                        Duet Wifi
                                        Zesty Nimble
                                        Mosaic Pallette+
                                        At work
                                        Renishaw AM250/400/ RenAM500M/500Q Powder Bed Fusion (Metal 3D Printers)

                                        1 Reply Last reply Reply Quote 0
                                        • jmjcokeundefined
                                          jmjcoke
                                          last edited by

                                          Thanks for the help, I am now up and running on RC5 with duetsoftwareframework 1.2.5.0. one of my mistakes was having the stable list still active.

                                          Joshua Coke

                                          Trick Laser Metal Max with Smart Effector
                                          Duet Wifi
                                          Zesty Nimble
                                          Mosaic Pallette+
                                          At work
                                          Renishaw AM250/400/ RenAM500M/500Q Powder Bed Fusion (Metal 3D Printers)

                                          1 Reply Last reply Reply Quote 0
                                          • First post
                                            Last post
                                          Unless otherwise noted, all forum content is licensed under CC-BY-SA