Duet 3 and g-code procedures and slicing

monster

I've been practicing with Cura.
I still can't get print/simulate directly from Cura. There I added 3 printers
One with http://printer.local address and some name != printer name in WebUI
Another with http://<ip_address> and some name != printer name in WebUI
and another with http://<ip_address> and some name == printer name in WebUI

attempt to print/simulate on either gives: There was a network error: 203 Error transferring ....

But I could upload it via WebUI and tried to print without filament - seems heads are moving right way

A Former User

I usually slice with simplify3d and for my start up I have the following in my start script in simplify3d which as you can see carries out numerous functions, this have been working well for a while now.

M290 S0.0 ; clear any baby stepping
G28 ; home all axes
G1 X20 Y50 ; move nozzle to start point
G92 E0 ; zero extruder
G1 Z0.5 ; lower nozzle
G1 Y250 E30 F1200 ; slow wipe
G92 E0 ; zero extruder
G1 Z2 ; lift nozzle
G29 S1 ; load height map

Phaedrux

Here's my start sequence for reference.

start.g

M106 P2 F30000 S0.5 H-1 C"Duet Fans"
M140 S65		; set heated bed to 65 and release
T0			; Select Tool 0
M291 P"Print Started. Preheating and Homing." T10
G4 S1
M98 P"0:/macros/Musical Tunes/LuckyTune.g" ; Lucky tune to start print off on the right foot
G4 S1
M220 S100		; Set speed factor back to 100% in case it was changed
M221 S100		; Set extrusion factor back to 100% in case it was changed
M290 R0 S0		; clear babystepping
M106 S0			; Turn part cooling blower off if it is on
G10 P0 R0 S80		; Set extruder to 80 and release
M190 S65		; set heated bed to 65 and wait
G28			; home XYZ
G29 S1			; load heightmap
M400
G10 P0 R80 S180	; Set extruder to 180 and release
M98 P"0:/sys/ZSpeedsPrint.g"	; Load Z speeds for printing
M98 P"0:/sys/CurrentsPrint.g"	; Load print motor currents
; Slicer Start Gcode begins.

ZSpeedsPrint.g

; 0:/sys/ZSpeedsPrint.g
; Used to set faster z speeds for printing.

M566 Z120			; Set maximum instantaneous speed changes (mm/min) (Jerk)
M203 Z600		; Set maximum speeds (mm/min)
M201 Z240 		; Set maximum accelerations (mm/s^2)

CurrentsPrint.g

; 0:/sys/CurrentsPrint.g
; Used to set normal motor current
; Make sure these values match those in config.g

M913 X80 Y80 Z80 E80					; set X Y Z E motors to 80% of their max current

Slicer start gcode

M98 P"0:/sys/PrimeNozzle.g"
M98 P"0:/sys/StartGCode.g"

Primenozzle.g

;M98 P"0:/sys/PrimeNozzle.g"

G90 			; Absolute positioning
G1 X1 Y270 F6000 	; Move to front left corner
M400 			; clear movement buffer
M116 			; Wait for temps
G1 Z0.3 F100		; Move Z to prime height
G91 			; Relative positioning
M83 			; Relative extrusion
G1 X40 E10 F300 	; Prime nozzle
G10			; Retract
G1 Y-1 X1 F10000 	; Wipe nozzle
M400

StartGcode.g

M291 P"Good luck and Godspeed." T5 ; Good luck and Godspeed.

; Battle Cry! 
;

M400
G4 S1
M300 P200 S523.25
G4 P200
M300 P200 S659.25
G4 P200
M300 P200 S739.99
G4 P250
M300 P285 S880.00
G4 P450
M300 P285 S880.00
G4 P285
M300 P625 S1108.73
G4 S1
M400		

;
; Start the print
;

Slicer End Gcode

M0 ; calls stop.g

Stop.g

; stop.g
; called when M0 (Stop) is run (e.g. when a print from SD card is cancelled)
; Also called by slicer end gcode by M0
;
M400			; Finish move queue
M104 S0 		; Extruder heater off
M140 S0 		; Bed heater off
M106 S255 		; Fan at 100 to cool nozzle and bed
G91			; Relative positioning
M220 S100		; Set speed factor back to 100% in case it was changed
M221 S100		; Set extrusion factor back to 100% in case it was changed
G1 E-2 F9000			; Retract filament 2mm
G1 X5 Y5 F9000		; Wipe nozzle 
G1 Z20 F500			; raise nozzle 5mm from printed part
G90				; absolute positioning
G1 X150 Y130 F6000		; Move x and Y axis over to bed center so probe is on top of bed
;M104 S35		; Set hot end low and wait
G4 S60			; Wait 5 minutes
;M116			; wait for temp to drop
G28 X Y			; Home X and Y
G28 X Y			; Home it again, Sam.
M290 R0 S0		; clear babystepping
M84			; Steppers off
M98 P"ZSpeedsNormal.g"	; Load normal z speed settings again.
M106 S0			; Fan off
M106 P2 F30000 L0.1 X0.8 B0.5 T35:70 H100:101:102 C"Duet Fans"

;Play a little beep beep beep to show print ended.
M400			; Clear queue again before jingle
G4 S1
M300 P250 S750
G4 P251
M300 P200 S1250
G4 P201
M300 P250 S750
G4 P251
M300 P200 S1250
G4 P201
M300 P250 S2500
G4 P251
M300 P150 S2000
G4 P151
M300 P150 S2500
G4 P151
M300 P350 S3700
G4 P351

Doing things this way has a few benefits. Mainly that the slicer start gcode is basically nothing. That way I only have to change the files on the Duet and regardless of which slicer I use the starting and ending behaviour is the same. It also allows me to do a preheat and nozzle prime and still allows the slicer to control the print temps.

monster

@Phaedrux Thanks for sharing - that sets the bar...

@Phaedrux said in Duet 3 and g-code procedures and slicing:

M98 P"0:/macros/Musical Tunes/LuckyTune.g" ; Lucky tune to start print off on the right foot

LOL

Phaedrux

@monster said in Duet 3 and g-code procedures and slicing:

LuckyTune.g

Sorry, I forgot that one.

; 0:/macros/Tunes/LuckyTune.g
; Lucky tune to start print off on the right foot
;

M400 ; Empty the movement buffer
M300 P200 S1000
G4 P210
M300 P200 S1250
G4 P210
M300 P200 S1100
G4 P201
M300 P200 S2000
G4 P201
M300 P200 S1500
G4 P201
M300 P200 S1000
G4 P201
M300 P200 S1300
G4 P201
M300 P200 S1000
G4 P201
M300 P300 S1500
M400 ; Empty the movement buffer

monster

@Phaedrux why do you use M400 often? I actually don't get why emptying of the buffer needed as command cause I though while one movement command is being executed then next command in script will not start. Which in turn means when next command is being executed all the movement of previous one is done. Or do I get some concept wrong? Perhaps movement buffer is not something I picture myself...

monster

@Phaedrux said in Duet 3 and g-code procedures and slicing:

Slicer start gcode

Another piece of setup I do not understand fully.
what is "Slicer start gcode"? (as well as "Slicer End Gcode")
Is it some script that defined in slicer software to be included in each g-code to print?
And then "0:/sys/PrimeNozzle.g" & "0:/sys/StartGCode.g" seems located in your printers files system, right? That means your slicer software is counting on presence of those files in printer, correct?
Or is "Slicer start gcode" an another script in printer that being called right before sliced model to be printed?

There are so many unknown things here I must admit. For example is there a list of standard scripts like start.g stop.g homex.g etc... that getting called in some occasions?

monster

@monster said in Duet 3 and g-code procedures and slicing:

@Phaedrux said in Duet 3 and g-code procedures and slicing:

Slicer start gcode

Another piece of setup I do not understand fully.
what is "Slicer start gcode"? (as well as "Slicer End Gcode")
Is it some script that defined in slicer software to be included in each g-code to print?

Got it! It is in printer settings in Cura!

Phaedrux

@monster said in Duet 3 and g-code procedures and slicing:

@Phaedrux why do you use M400 often? I actually don't get why emptying of the buffer needed as command cause I though while one movement command is being executed then next command in script will not start. Which in turn means when next command is being executed all the movement of previous one is done. Or do I get some concept wrong? Perhaps movement buffer is not something I picture myself...

Probably unnecessary for the most part, done mostly out of habit during troubleshooting. Basically M400 just says wait until the movement queue is complete up to this point before executing what comes after.

For the music bits I found M400 before helped it play the tones more consistently without stutters, but I haven't tested that in quite some time.

Phaedrux

@monster said in Duet 3 and g-code procedures and slicing:

what is "Slicer start gcode"? (as well as "Slicer End Gcode")
Is it some script that defined in slicer software to be included in each g-code to print?

Yes that's right. Most slicers have a section of text boxes that allow you to enter custom gcode commands that will get inserted at certain locations, such as before the print starts, when the print is finished, at layer changes, at tool changes, etc.

Example from PrusaSlicer:
Screenshot 2020-04-10 10.22.39.png

@monster said in Duet 3 and g-code procedures and slicing:

And then "0:/sys/PrimeNozzle.g" & "0:/sys/StartGCode.g" seems located in your printers files system, right?

That's right. M98 allows you to call a macro found on the Duet SD card, either in the macros or sys folder.

@monster said in Duet 3 and g-code procedures and slicing:

For example is there a list of standard scripts like start.g stop.g homex.g etc... that getting called in some occasions?

Yes, there is.
https://duet3d.dozuki.com/Wiki/Setting_up_macro_files_for_common_tasks
https://duet3d.dozuki.com/Wiki/Macros

resam

@monster said in Duet 3 and g-code procedures and slicing:

There was a network error: 203 Error transferring ....

Apparently Duet3 with SBC does not provide the same API as RepRapFirmware 2 and previous. This means all the slicer integrations are broken - I know of at least PrusaSlicer, and the Cura plugin (I am the maintainer if it).

Looks like once it is RRF that broke compatibility with slicers - usually it is slicers who break magic comments and other things

@dc42 @chrishamm any thoughts on this topic? It would be really nice if the well-known RRF HTTP API with rr_connect etc. would also be supported on Duet3+SBC!
It's not only slicers, also lots of other scripts, timelapse tools, and other integrations were relying on this API.

monster

@Phaedrux said in Duet 3 and g-code procedures and slicing:

@monster said in Duet 3 and g-code procedures and slicing:

For example is there a list of standard scripts like start.g stop.g homex.g etc... that getting called in some occasions?

Yes, there is.
https://duet3d.dozuki.com/Wiki/Setting_up_macro_files_for_common_tasks
https://duet3d.dozuki.com/Wiki/Macros

Priceless!

monster

I can't remember where did I read that by now.
But back then when I was choosing controller I did read somewhere that when Duet 3 used with Pi it (or I guess Pi) can do slicing. And if my memory not mistaking that was saying about actually Cura slicer in Pi.

Is it something I could try? I mean try to use that slicer.
Hope it is not to difficult to setup and use. May be that could solve my problem...

Phaedrux

Yes you could run a slicer on the pi, but it will be a bit slower than on your PC and I don't think it would solve any of your problems.