Duet3D Logo Duet3D
    • Tags
    • Documentation
    • Order
    • Register
    • Login

    Cannot change can address with M952: Command is not supported

    Scheduled Pinned Locked Moved
    Duet Hardware and wiring
    4
    12
    488
    Loading More Posts
    • Oldest to Newest
    • Newest to Oldest
    • Most Votes
    Reply
    • Reply as topic
    Log in to reply
    This topic has been deleted. Only users with topic management privileges can see it.
    • Danalundefined
      Danal
      last edited by

      What release is your main board?

      M115 B0

      Delta / Kossel printer fanatic

      jdumoulinundefined 1 Reply Last reply Reply Quote 0
      • jdumoulinundefined
        jdumoulin @Danal
        last edited by

        @Danal
        m115 b0
        FIRMWARE_NAME: RepRapFirmware for Duet 3 MB6HC v0.6 or 1.0 FIRMWARE_VERSION: 3.0 ELECTRONICS: Duet 3 MB6HC FIRMWARE_DATE: 2020-01-03b3

        T3P3Tonyundefined 1 Reply Last reply Reply Quote 0
        • T3P3Tonyundefined
          T3P3Tony administrators @jdumoulin
          last edited by

          @jdumoulin you need to update to 3.01 (best to go for 3.01 RC11) remeber to read the whatsnew file.

          www.duet3d.com

          jdumoulinundefined 1 Reply Last reply Reply Quote 0
          • jdumoulinundefined
            jdumoulin @T3P3Tony
            last edited by

            @T3P3Tony said in Cannot change can address with M952: Command is not supported:

            @jdumoulin you need to update to 3.01 (best to go for 3.01 RC11) remeber to read the whatsnew file.

            Thanks for letting me know.
            I did an upgrade all this morning. Why would I not have the latest firmware?

            1 Reply Last reply Reply Quote 0
            • jdumoulinundefined
              jdumoulin
              last edited by

              NM I just noticed I did an update all twice but no upgrade all

              1 Reply Last reply Reply Quote 0
              • Danalundefined
                Danal
                last edited by

                Which "feed" are you on? Stable or unstable?

                If you don't know, please post the output of a sudo apt update (which, despite its name, does not actually change anything running on your system).

                Delta / Kossel printer fanatic

                jdumoulinundefined 1 Reply Last reply Reply Quote 0
                • jdumoulinundefined
                  jdumoulin
                  last edited by

                  @Danal said in Cannot change can address with M952: Command is not supported:

                  sudo apt update

                  I upgraded to RC11 through duet web control and now I am getting "Failed to connect to duet 3 DCS unavailable"

                  This project is driving me bonkers. lol

                  sudo apt update
                  Hit:1 http://archive.raspberrypi.org/debian buster InRelease
                  Hit:2 http://raspbian.raspberrypi.org/raspbian buster InRelease
                  Hit:3 https://pkg.duet3d.com stable InRelease
                  Reading package lists... Done
                  Building dependency tree
                  Reading state information... Done
                  10 packages can be upgraded. Run 'apt list --upgradable' to see them.

                  1 Reply Last reply Reply Quote 0
                  • jdumoulinundefined
                    jdumoulin @Danal
                    last edited by

                    @Danal

                    Your question pointed me in the right direction and I switched to the unstable feed and did an upgrade. Browser acces is back.

                    Now a M952 B10 A20 gives me a Warning: M952: Board 10 received unknown msg type 2010

                    1 Reply Last reply Reply Quote 1
                    • jdumoulinundefined
                      jdumoulin
                      last edited by

                      OK, figured it out. after this I upgraded the tool board after which its address changed to 121. So now I did a M952 B121 A20 and it changed the addres to 20.
                      Now m115 b20 responds with:
                      Board TOOL1LC firmware 3.01-RC11 (2020-04-30b1)

                      Thank you!

                      Jay

                      1 Reply Last reply Reply Quote 1
                      • jdumoulinundefined
                        jdumoulin
                        last edited by

                        So where do I find information on how toset up this tool board in the config file? It is not listed at all in the documentation.

                        dc42undefined 1 Reply Last reply Reply Quote 0
                        • dc42undefined
                          dc42 administrators @jdumoulin
                          last edited by dc42

                          @jdumoulin said in Cannot change can address with M952: Command is not supported:

                          So where do I find information on how toset up this tool board in the config file? It is not listed at all in the documentation.

                          Set up the fans. drivers, heaters etc. in config.g just as you would set up a local driver; except that the driver number on the tool board is 20.1, the high current (heater) output is pin "20.out0", the 12V outputs for fans are "20.out1" and "20.out2", the temperature sensors are "20.temp0" and "20.temp1", and the IO (Z probe) connector is "20.io0.out" and "20.io0.in".

                          If you want an example, you can find a config.g file for a tool changer with one tool board (at address 23) at https://github.com/Duet3D/RRF-machine-config-files/tree/master/E3D_Tool_Changer/dc42-duet3-centreZero-2Titan-2Hemera.

                          HTH David

                          PS - the full list of tool board pin names, excluding the motor driver, is at https://duet3d.dozuki.com/Wiki/RepRapFirmware_3_overview#Section_Duet_3_Tool_Board_1LC_pin_names.

                          Duet WiFi hardware designer and firmware engineer
                          Please do not ask me for Duet support via PM or email, use the forum
                          http://www.escher3d.com, https://miscsolutions.wordpress.com

                          1 Reply Last reply Reply Quote 1
                          • First post
                            Last post
                          Unless otherwise noted, all forum content is licensed under CC-BY-SA