Smart effector first layer issues

Carlo

@Lakeman

That is good !

So run probe offset then G29 and try a print after you re run

Lakeman

During the delta calibration and mesh it goes much more gentle still, should that tap at the same speed?

Lakeman

Print with or without mesh?

Carlo

@Lakeman

Thats normal probe tests are F3000 your G31 F1200

So probe offset then G29 new height map sorry

Carlo

@Carlo
print with G29 S1

Lakeman

The new height map, I did not do a delta calibration, and the first layer did fail

Lakeman

Thanks a lot for the help so far, hopefully we will get there. I have to get going a little but, just keep posting, but I will try it later tonight or tomorrow. Thanks a lot!!

Carlo

@Lakeman

Wow explosive!

; Heat bed to 60C & nozzle to 130C
M104 S130 T0
M190 S60 T0
M109 S130 T0
M106 P2 S0
G31 P100 X0 Y0 Z0 ; Reset Z trigger height to 0mm
M290 R0 S0 ; Reset babystepping
G29 S2 ; Clear bed mesh
G28 ; Home the effector
G1 X0 Y0 Z20 F1200 ; Move close to the bed
G30 ; Probe to find a rough Z 0mm

G1 X0 Y0 Z1 F1200 ; Move the nozzle to Z 1mm slowly
G92 Z3.0 ; Set the Z height to 3mm, allowing moves below 0
M291 P"Lower the nozzle to until it touches a 0.10mm shim. Click to continue." S2 Z1
G92 Z0 ; Define this point as 0mm
G1 X0 Y0 Z20 ; Move the probe to Z 20mm
G30 S-3 ; Probe and set the trigger height
G1 Z20 ; Raise Z to 20mm

Try that then G29 dont run calibration

Carlo

@Lakeman

We will get there I had weeks of this!

Lakeman

ALright, I followed the sequense discribed above, afterwards run a mesh compensation with similar result

Carlo

@Lakeman

Ok add the 2mm back to M665 H run the macro again please then G29

Lakeman

This should be a delta calibration issue I guess. Probably the delta radius or so

Carlo

@Lakeman
We change the height based off of the Z0 yesterday so adding it back to rule that out

Also send M672 see what it spits out

Lakeman

Added 2mm
Ran the macro and g29:

m672
Error: M672: No program bytes provided

Carlo

@Carlo

Run the macro then delta calibrate then G29 sorry Dopy moment here

Carlo

@Lakeman
Wasn't sure it talks back that's fine

Lakeman

Ok. Done the macro again,
G32
Calibrated 6 factors using 16 points, (mean, deviation) before (1.067, 0.643) after (0.000, 0.063)
G29:

Lakeman

m665
Diagonals 440.480:440.480:440.480, delta radius 231.706, homed height 420.175, bed radius 185.0, X 0.287°, Y 0.164°, Z 0.000°

m666
Endstop adjustments X0.28 Y0.16 Z-0.44, tilt X0.00% Y0.00%

droftarts

@Lakeman This is a good page for visualising the effects of the delta (M665) parameters: http://boim.com/DeltaUtil/CalDoc/Calibration.html
I'd guess your delta radius is wrong. Set up and run autocalibration. See https://duet3d.dozuki.com/Wiki/Calibrating_a_delta_printer

Edit: never mind, you got there!

Ian

Lakeman

I entered the values of the delta calibration in the config file, ran the macro and G29: