Duet3D Logo Duet3D
    • Tags
    • Documentation
    • Order
    • Register
    • Login

    Temperature fault macro

    Scheduled Pinned Locked Moved
    General Discussion
    4
    14
    1.7k
    Loading More Posts
    • Oldest to Newest
    • Newest to Oldest
    • Most Votes
    Reply
    • Reply as topic
    Log in to reply
    This topic has been deleted. Only users with topic management privileges can see it.
    • dc42undefined
      dc42 administrators
      last edited by

      If you press the nozzle icon on PanelDue above the temperature reading, that will activate that tool and allow you to set the temperature.

      Duet WiFi hardware designer and firmware engineer
      Please do not ask me for Duet support via PM or email, use the forum
      http://www.escher3d.com, https://miscsolutions.wordpress.com

      1 Reply Last reply Reply Quote 0
      • jrledererundefined
        jrlederer
        last edited by

        Hi David,
        Not sure whether updating to the latest panel firmware on your github may have caused a bad firmware install in my case, or what may be the case, but after issuing M562 P1, the errored heater channel change from purple to clear background indictating no fault, but state being OFF. A that's what I know used to work – pressing the icon of the corresponding nozzle on the controls page -- but now no matter what I try to do I cannot get it to flip over to color red (ie. Heating). Any ideas?

        –

        "Insanity is doing the same thing over again, yet expecting different results..." --Albert Einstein

        1 Reply Last reply Reply Quote 0
        • dc42undefined
          dc42 administrators
          last edited by

          Hmm… Pressing the nozzle icon and setting the temperature should still work.

          Duet WiFi hardware designer and firmware engineer
          Please do not ask me for Duet support via PM or email, use the forum
          http://www.escher3d.com, https://miscsolutions.wordpress.com

          1 Reply Last reply Reply Quote 0
          • jrledererundefined
            jrlederer
            last edited by

            No dice…maybe it has to do with my commands that I'm entering in the panelDue? I enter the console page and press the keyboard icon, then type in M562P1, which is the command I think rates the heater channel 1 which is where my extruders cartridge heater is installed, then switch to the control page and click on the nozzle icon on channel one, but it resists switching to the color which would indicate that it is active again. No matter what I press or change temps to, the floor behind the current temperature reading remains clear and thereafter, I cannot, by any means I'm aware of, get the temperature to go upwards. Please advise.

            Thanks, in advance.

            Jonathan

            –

            "Insanity is doing the same thing over again, yet expecting different results..." --Albert Einstein

            1 Reply Last reply Reply Quote 0
            • Janundefined
              Jan
              last edited by

              I have the same issue.
              I can reset temp faults with M562 P1 on the paneldue, but to set the heater active I have to use the web interface. With the nozzle button I can only toggle off/standby after the fault (normally it works … Also for the bed it works)

              1 Reply Last reply Reply Quote 0
              • jrledererundefined
                jrlederer
                last edited by

                Same here…so I'm not alone then...

                –

                "Insanity is doing the same thing over again, yet expecting different results..." --Albert Einstein

                1 Reply Last reply Reply Quote 0
                • dc42undefined
                  dc42 administrators
                  last edited by

                  Does sending command T0 after M562 P1 work?

                  Duet WiFi hardware designer and firmware engineer
                  Please do not ask me for Duet support via PM or email, use the forum
                  http://www.escher3d.com, https://miscsolutions.wordpress.com

                  1 Reply Last reply Reply Quote 0
                  • jrledererundefined
                    jrlederer
                    last edited by

                    I'll try and post results in a few minutes…please stand by...

                    [Edit:]

                    Okay, so interesting update IMO:

                    I literally just performed the update to 1.19b1 according to the procedure in the wiki involving dual update via M997 S0:1 after placing both the files and renaming them to be exactly as specified. So, FWIW, the firmware was just freshly loaded brand newly…

                    As a handy coincidence, upon heating my extruder to 210 in order to pull out the existing filament to replace it with ABS instead, the heater incurred an error of temp rising more slowly than expected. I went to panelDue and typed in M562 P1, after which the error (purple BG) was cleared and I tried pressing the nozzle icon to see if it would activate the OFF heater. No love as has been the case for a while now.

                    I typed in T0, after which I tried clicking the nozzle icon again, but still no response. Just for kicks I typed in T1. Upon switching back to the Control page of PanelDue, the numerical temperature value below the nozzle icon was yellow (standby). Further clicking on the nozzle resulted in operation as expected! So, it's a workaround, but it works!

                    Thanks!

                    –

                    "Insanity is doing the same thing over again, yet expecting different results..." --Albert Einstein

                    1 Reply Last reply Reply Quote 0
                    • Janundefined
                      Jan
                      last edited by

                      I have not done the latest update yet, bit I can confirm that with T0/T1 it now works also on the paneldue.
                      However, thanks to David's mod proposed on the TV issues I hope not to see too many heater faults any more 😉

                      1 Reply Last reply Reply Quote 0
                      • jrledererundefined
                        jrlederer
                        last edited by

                        TV issues…?

                        –

                        "Insanity is doing the same thing over again, yet expecting different results..." --Albert Einstein

                        1 Reply Last reply Reply Quote 0
                        • Janundefined
                          Jan
                          last edited by

                          Sorry, TC issues … Autocorrect on my mobile 😉

                          1 Reply Last reply Reply Quote 0
                          • First post
                            Last post
                          Unless otherwise noted, all forum content is licensed under CC-BY-SA