BLTouch Zprobe marche pas

[chris974M]

@Phaedrux said in BLTouch Zprobe marche pas:

M122

M122
=== Diagnostics ===
RepRapFirmware for Duet 2 WiFi/Ethernet version 3.1.1 running on Duet WiFi 1.02 or later + DueX5
Board ID: 08DLM-996RU-N8PS4-6JKD8-3S06T-KBVRN
Used output buffers: 1 of 24 (10 max)
=== RTOS ===
Static ram: 27980
Dynamic ram: 94224 of which 44 recycled
Exception stack ram used: 264
Never used ram: 8560
Tasks: NETWORK(ready,416) HEAT(blocked,1224) DUEX(suspended,160) MAIN(running,1824) IDLE(ready,80)
Owned mutexes: WiFi(NETWORK)
=== Platform ===
Last reset 00:01:17 ago, cause: software
Last software reset at 2020-10-08 00:05, reason: User, spinning module GCodes, available RAM 8560 bytes (slot 1)
Software reset code 0x0003 HFSR 0x00000000 CFSR 0x00000000 ICSR 0x0441f000 BFAR 0xe000ed38 SP 0xffffffff Task MAIN
Error status: 0
MCU temperature: min 23.8, current 24.4, max 24.9
Supply voltage: min 24.1, current 24.2, max 24.4, under voltage events: 0, over voltage events: 0, power good: yes
Driver 0: standstill, SG min/max not available
Driver 1: standstill, SG min/max not available
Driver 2: standstill, SG min/max not available
Driver 3: standstill, SG min/max not available
Driver 4: standstill, SG min/max not available
Driver 5: standstill, SG min/max not available
Driver 6: standstill, SG min/max not available
Driver 7: standstill, SG min/max not available
Driver 8: standstill, SG min/max not available
Driver 9: standstill, SG min/max not available
Date/time: 2020-10-08 00:07:10
Cache data hit count 133234046
Slowest loop: 5.10ms; fastest: 0.12ms
I2C nak errors 0, send timeouts 0, receive timeouts 0, finishTimeouts 0, resets 0
=== Storage ===
Free file entries: 10
SD card 0 detected, interface speed: 20.0MBytes/sec
SD card longest read time 3.5ms, write time 0.0ms, max retries 0
=== Move ===
Hiccups: 0(0), FreeDm: 169, MinFreeDm: 169, MaxWait: 0ms
Bed compensation in use: none, comp offset 0.000
=== MainDDARing ===
Scheduled moves: 0, completed moves: 0, StepErrors: 0, LaErrors: 0, Underruns: 0, 0 CDDA state: -1
=== AuxDDARing ===
Scheduled moves: 0, completed moves: 0, StepErrors: 0, LaErrors: 0, Underruns: 0, 0 CDDA state: -1
=== Heat ===
Bed heaters = 0 -1 -1 -1, chamberHeaters = -1 -1 -1 -1
=== GCodes ===
Segments left: 0
Movement lock held by null
HTTP is ready with "M122 " in state(s) 0
Telnet is idle in state(s) 0
File is idle in state(s) 0
USB is idle in state(s) 0
Aux is idle in state(s) 0
Trigger is idle in state(s) 0
Queue is idle in state(s) 0
Daemon is idle in state(s) 0
Autopause is idle in state(s) 0
Code queue is empty.
=== Network ===
Slowest loop: 15.65ms; fastest: 0.00ms
Responder states: HTTP(0) HTTP(0) HTTP(0) HTTP(0) FTP(0) Telnet(0), 0 sessions
HTTP sessions: 1 of 8

• WiFi -
  Network state is active
  WiFi module is connected to access point
  Failed messages: pending 0, notready 0, noresp 0
  WiFi firmware version 1.23
  WiFi MAC address f4:cf:a2:66:94:6a
  WiFi Vcc 3.43, reset reason Unknown
  WiFi flash size 4194304, free heap 26096
  WiFi IP address 192.168.1.122
  WiFi signal strength -57dBm, reconnections 0, sleep mode modem
  Socket states: 0 0 0 0 0 0 0 0
  === DueX ===
  Read count 1, 0.77 reads/min

[chris974M]

@Phaedrux said in BLTouch Zprobe marche pas:

M98

M98 P"config.g"
HTTP is enabled on port 80
FTP is disabled
TELNET is disabled
Warning: Heater 0 appears to be over-powered. If left on at full power, its temperature is predicted to reach 365C
Error: M305 has been replaced by M308 and M950 in RepRapFirmware 3
Warning: Heater 1 appears to be over-powered. If left on at full power, its temperature is predicted to reach 605C

[Phaedrux]

@chris974M said in BLTouch Zprobe marche pas:

M305 P1 T4606017 B5848 C5.548428e-8 R4700 H0 L0

Remove that line, though it's not related to the bltouch issue.

Are you able to try PWM1?

[chris974M]

ok i try

[chris974M]

que faut il que je change pour PWM1

[chris974M]

Example 4 (BLTouch on Duet WiFi) - old code:

M558 P9 H5 F120 T3000 ; BLTouch connected to Z probe IN pin
M307 H3 A-1 C-1 D-1 ; free up heater 3 to use as BLTouch servo pin
...
M280 P3 S10 I1 ; send control signal to BLTouch through heater 3 pin
New code:

M558 P9 C"^zprobe.in" H5 F120 T3000 ; BLTouch connected to Z probe IN pin
M950 S0 C"exp.heater3" ; create servo/gpio 0 on heater 3 pin on expansion connector
...
M280 P0 S10 ; send control signal to BLTouch through servo/gpio 0

[chris974M]

M558 P9 C "^ zprobe.in " H5 F120 T3000; BLTouch connecté à la sonde Z IN pin
M950 S0 C "duex.pwm1"; créer servo / gpio 0 sur l'élément chauffant 3 broches sur le connecteur d'extension
...
M280 P0 S10; envoyer un signal de commande à BLTouch via servo / gpio 0

Like that or nope

[chris974M]

Avertissement: le réchauffeur 0 semble être suralimenté. S'il est laissé allumé à pleine puissance, sa température devrait atteindre 365 ° C.
Avertissement: le réchauffeur 1 semble être suralimenté. S'il est laissé allumé à pleine puissance, sa température devrait atteindre 605 ° C

is it normal ?

[Phaedrux]

@chris974M said in BLTouch Zprobe marche pas:

Avertissement: le réchauffeur 0 semble être suralimenté. S'il est laissé allumé à pleine puissance, sa température devrait atteindre 365 ° C.
Avertissement: le réchauffeur 1 semble être suralimenté. S'il est laissé allumé à pleine puissance, sa température devrait atteindre 605 ° C

is it normal ?

Yes. https://duet3d.dozuki.com/Wiki/FAQ#Section_M307_Heater_1_appears_to_be_over_powered_If_left_on_at_full_power_its_temperature_is_predicted_to_reach_521C

[Phaedrux]

@chris974M said in BLTouch Zprobe marche pas:

M558 P9 C "^ zprobe.in " H5 F120 T3000; BLTouch connecté à la sonde Z IN pin
M950 S0 C "duex.pwm1"; créer servo / gpio 0 sur l'élément chauffant 3 broches sur le connecteur d'extension
...
M280 P0 S10; envoyer un signal de commande à BLTouch via servo / gpio 0

Like that or nope

Yes it should be like that.

[chris974M]

@Phaedrux said in BLTouch Zprobe marche pas:

duex.pwm

M280 before or after the line G31

[chris974M]

@Phaedrux said in BLTouch Zprobe marche pas:

M280 P0 S10; envoyer un signal de commande à BLTouch via servo / gpio 0

Its WORK

[chris974M]

; Configuration file for Duet WiFi (firmware version 3)
; executed by the firmware on start-up
;
; generated by RepRapFirmware Configuration Tool v3.1.4 on Sat Oct 03 2020 15:26:33 GMT+0200 (heure d’été d’Europe centrale)

; General preferences
G90 ; send absolute coordinates...
M83 ; ...but relative extruder moves
M550 P"MonsterPrinter" ; set printer name

; Network
M552 S1 ; enable network
M586 P0 S1 ; enable HTTP
M586 P1 S0 ; disable FTP
M586 P2 S0 ; disable Telnet

; Drives
M569 P0 S1 ; physical drive 0 goes forwards
M569 P1 S0 ; physical drive 1 goes forwards
M569 P2 S1 ; physical drive 2 goes forwards
M569 P3 S1 ; physical drive 3 goes forwards
M569 P5 S1 ; physical drive 5 goes forwards
M569 P6 S1 ; physical drive 6 goes forwards
M569 P7 S0 ; physical drive 7 goes forwards
M584 X0:5 Y1:6 Z2:7 E3 ; set drive mapping
M350 X16 Y16 Z16 E16 I1 ; configure microstepping with interpolation
M92 X100.00 Y80.00 Z400.00 E420.00 ; set steps per mm
M566 X900.00 Y1400.00 Z12.00 E120.00 ; set maximum instantaneous speed changes (mm/min)
M203 X9000.00 Y9000.00 Z180.00 E1200.00 ; set maximum speeds (mm/min)
M201 X500.00 Y500.00 Z20.00 E250.00 ; set accelerations (mm/s^2)
M906 X1700 Y2400 Z1700 E800 I30 ; set motor currents (mA) and motor idle factor in per cent
M84 S30 ; Set idle timeout

; Axis Limits
M208 X-6 Y-10 Z0 S1 ; set axis minima
M208 X780 Y510 Z350 S0 ; set axis maxima

; Endstops
M574 X1 S1 P"xstop" ; configure active-high endstop for low end on X via pin xstop
M574 Y2 S1 P"ystop" ; configure active-high endstop for high end on Y via pin ystop
M574 Z1 S2 ; configure Z-probe endstop for low end on Z

; Z-Probe
M558 P9 C"^zprobe.in" H5 F120 T6000 ; BLTouch connected to Z probe IN pin
M950 S0 C"duex.pwm1" ; create servo/gpio 0 on heater 3 pin on expansion
M280 P0 S10 ; envoyer un signal de commande à BLTouch via servo / gpio 0
G31 P500 X0 Y20 Z3.71 ; set Z probe trigger value, offset and trigger height
M557 X40:780 Y80:510 S100 ; define mesh grid

; Heaters
M308 S0 P"bedtemp" Y"thermistor" T100000 B3950 ; configure sensor 0 as thermistor on pin bedtemp
M950 H0 C"bedheat" T0 ; create bed heater output on bedheat and map it to sensor 0
M307 H0 B0 S1.00 ; disable bang-bang mode for the bed heater and set PWM limit
M140 H0 ; map heated bed to heater 0
M143 H0 S150 ; set temperature limit for heater 0 to 150C
M308 S1 P"e0temp" Y"thermistor" T4606017 B5848 ; configure sensor 1 as thermistor on pin e0temp
M950 H1 C"e0heat" T1 ; create nozzle heater output on e0heat and map it to sensor 1
M307 H1 A580.4 C256.6 D6.4 S0.50 ; disable bang-bang mode for heater and set PWM limit
M143 H1 S493
; Fans
M950 F0 C"fan0" Q500 ; create fan 0 on pin fan0 and set its frequency
M106 P0 S0 H-1 ; set fan 0 value. Thermostatic control is turned off
M950 F1 C"fan1" Q500 ; create fan 1 on pin fan1 and set its frequency
M106 P1 S1 H1 T45 ; set fan 1 value. Thermostatic control is turned on

; Tools
M563 P0 D0 H1 F0 ; define tool 0
G10 P0 X0 Y0 Z0 ; set tool 0 axis offsets
G10 P0 R0 S0 ; set initial tool 0 active and standby temperatures to 0C

; Custom settings are not defined

; Miscellaneous
M911 S10 R11 P"M913 X0 Y0 G91 M83 G1 Z3 E-5 F1000" ; set voltage thresholds and actions to run on power loss

[chris974M]

Pour le BLTouch avec DUEX5 brancher sur PWM1
si sa peut aider quelqu'un d'autre

[chris974M]

My pin Is down during homing XY why ?

[Phaedrux]

Post your homing files. Does m401 and m402 work?

[chris974M]

; homeall.g
; called to home all axes
;
; generated by RepRapFirmware Configuration Tool v3.1.4 on Sat Oct 03 2020 15:26:33 GMT+0200 (heure d’été d’Europe centrale)
G91 ; relative positioning
G1 H2 Z5 F8000 ; lift Z relative to current position
G1 H1 X-787 Y505 F3600 ; move quickly to X and Y axis endstops and stop there (first pass)
G1 H2 X5 Y-5 F8000 ; go back a few mm
G1 H1 X-787 Y505 F600 ; move slowly to X and Y axis endstops once more (second pass)
G90 ; absolute positioning
G1 X390 Y250 F8000 ; go to first bed probe point and home Z
G30 ; home Z by probing the bed

; Uncomment the following lines to lift Z after probing
;G91 ; relative positioning
;G1 Z5 F100 ; lift Z relative to current position
;G90 ; absolute positioning

; homez.g
; called to home the Z axis
;
; generated by RepRapFirmware Configuration Tool v3.1.4 on Sat Oct 03 2020 15:26:33 GMT+0200 (heure d’été d’Europe centrale)
G91 ; relative positioning
G1 H2 Z5 F8000 ; lift Z relative to current position
G90 ; absolute positioning
G1 X390 Y250 F8000 ; go to first probe point
G30 ; home Z by probing the bed

; Uncomment the following lines to lift Z after probing
;G91 ; relative positioning
;G1 Z5 F100 ; lift Z relative to current position
;G90 ; absolute positioning

[chris974M]

M401 and M402 work

[chris974M]

BEFORE
M280 P0 S10 ; envoyer un signal de commande à BLTouch via servo / gpio 0
NEW
M280 P0 S90 ; envoyer un signal de commande à BLTouch via servo / gpio 0

Just that Thanks

[chris974M]

thank you phaedrux for your help