Job Processing
-
Everything was working fine yesterday, but today we went to start a job and the print never starts, just processing
we have tried sending a different job, and even the old turn off and back on
we ran a m122 but really don't know what it might dhow as the problem that we are missing
8:11:34 AM=== Diagnostics ===
RepRapFirmware for Duet 2 WiFi/Ethernet version 2.05 running on Duet WiFi 1.02 or later + DueX5
Board ID: 08DLM-996RU-N85T0-6J1D4-3SJ6K-TAVZR
Used output buffers: 1 of 24 (11 max)
=== RTOS ===
Static ram: 25712
Dynamic ram: 94196 of which 0 recycled
Exception stack ram used: 424
Never used ram: 10740
Tasks: NETWORK(ready,628) HEAT(blocked,1176) DUEX(suspended,160) MAIN(running,3728) IDLE(ready,160)
Owned mutexes:
=== Platform ===
Last reset 00:07:25 ago, cause: software
Last software reset at 2020-10-14 08:04, reason: User, spinning module GCodes, available RAM 10764 bytes (slot 2)
Software reset code 0x0003 HFSR 0x00000000 CFSR 0x00000000 ICSR 0x0441f000 BFAR 0xe000ed38 SP 0xffffffff Task 0x4e49414d
Error status: 0
Free file entries: 9
SD card 0 detected, interface speed: 20.0MBytes/sec
SD card longest block write time: 20.1ms, max retries 0
MCU temperature: min 32.1, current 32.4, max 33.2
Supply voltage: min 23.3, current 24.1, max 24.3, under voltage events: 0, over voltage events: 0, power good: yes
Driver 0: standstill, SG min/max not available
Driver 1: standstill, SG min/max not available
Driver 2: standstill, SG min/max 0/538
Driver 3: standstill, SG min/max not available
Driver 4: standstill, SG min/max not available
Driver 5: standstill, SG min/max not available
Driver 6: standstill, SG min/max not available
Driver 7: standstill, SG min/max not available
Driver 8: standstill, SG min/max not available
Driver 9: standstill, SG min/max not available
Date/time: 2020-10-14 08:11:33
Cache data hit count 1339471581
Slowest loop: 55.31ms; fastest: 0.07ms
I2C nak errors 0, send timeouts 0, receive timeouts 0, finishTimeouts 0, resets 0
=== Move ===
Hiccups: 0, FreeDm: 160, MinFreeDm: 158, MaxWait: 101266ms
Bed compensation in use: mesh, comp offset 0.273
=== DDARing ===
Scheduled moves: 6, completed moves: 6, StepErrors: 0, LaErrors: 0, Underruns: 0, 0
=== Heat ===
Bed heaters = 0 -1 -1 -1, chamberHeaters = 5 -1
Heater 0 is on, I-accum = 0.0
Heater 1 is on, I-accum = 0.2
Heater 5 is on, I-accum = 0.7
=== GCodes ===
Segments left: 0
Stack records: 2 allocated, 0 in use
Movement lock held by file
http is idle in state(s) 0
telnet is idle in state(s) 0
file is doing "M116 " in state(s) 0
serial is idle in state(s) 0
aux is idle in state(s) 0
daemon is idle in state(s) 0
queue is idle in state(s) 0
autopause is idle in state(s) 0
Code queue is empty.
=== Network ===
Slowest loop: 30.55ms; fastest: 0.01ms
Responder states: HTTP(0) HTTP(0) HTTP(0) HTTP(0) FTP(0) Telnet(0) Telnet(0)
HTTP sessions: 2 of 8- WiFi -
Network state is running
WiFi module is connected to access point
Failed messages: pending 0, notready 0, noresp 0
WiFi firmware version 1.23
WiFi MAC address ec:fa:bc:5b:41:b9
WiFi Vcc 3.38, reset reason Turned on by main processor
WiFi flash size 4194304, free heap 26184
WiFi IP address 192.168.5.248
WiFi signal strength -56dBm, reconnections 0, sleep mode modem
Socket states: 0 0 0 0 0 0 0 0
=== Filament sensors ===
Extruder 0 sensor: ok
Extruder 1 sensor: ok
Duet WiFi 1.02 or later + DueX5 Firmware Version: 2.05 (2019-12-13b1)
Thank You - WiFi -
-
I would suggest updating to 2.05.1
https://github.com/Duet3D/RepRapFirmware/releases/tag/2.05.1 -
If that doesn't help, try a different SD card.
Are you sure nothing has changed in the config or slicer setup?
Are temperatures reporting correctly?
Can you jog axis at all?
How are you trying to start the print job?
