Duet3D Logo Duet3D
    • Tags
    • Documentation
    • Order
    • Register
    • Login

    Error: Failed to initialise WiFi module, code -10 on 2.05

    Scheduled Pinned Locked Moved Unsolved
    General Discussion
    wifi duet 2 wifi error wifi module duet 2 wifi
    5
    20
    1.6k
    Loading More Posts
    • Oldest to Newest
    • Newest to Oldest
    • Most Votes
    Reply
    • Reply as topic
    Log in to reply
    This topic has been deleted. Only users with topic management privileges can see it.
    • JairoRBundefined
      JairoRB @Phaedrux
      last edited by

      @Phaedrux Here is the result after doing exactly what you asked:

      M552 S-1
      ok
      M552 S0
      ok
      WiFi module started
      Error: Failed to initialise WiFi module, code -10
      M997 S0:1
      Trying to connect at 230400 baud:  success
      Erasing 4096 bytes...
      Erasing 212992 bytes...
      Uploading file...
      5% complete
      10% complete
      15% complete
      20% complete
      25% complete
      30% complete
      35% complete
      40% complete
      45% complete
      50% complete
      55% complete
      60% complete
      65% complete
      70% complete
      75% complete
      80% complete
      85% complete
      90% complete
      95% complete
      Upload successful
      M552 S0
      ok
      WiFi module started
      Error: Failed to initialise WiFi module, code -10
      M122
      === Diagnostics ===
      RepRapFirmware for Duet 2 WiFi/Ethernet version 2.05.1 running on Duet WiFi 1.02 or later
      Board ID: 08DGM-917NK-F2MS4-7JTDL-3S86K-TWTJF
      Used output buffers: 1 of 24 (1 max)
      === RTOS ===
      Static ram: 25712
      Dynamic ram: 93552 of which 0 recycled
      Exception stack ram used: 256
      Never used ram: 11552
      Tasks: NETWORK(ready,1408) HEAT(blocked,1256) MAIN(running,3816) IDLE(ready,160)
      Owned mutexes:
      === Platform ===
      Last reset 00:00:25 ago, cause: power up
      Last software reset time unknown, reason: User, spinning module GCodes, available RAM 11488 bytes (slot 1)
      Software reset code 0x0003 HFSR 0x00000000 CFSR 0x00000000 ICSR 0x04433000 BFAR 0xe000ed38 SP 0xffffffff Task 0x4e49414d
      Error status: 0
      Free file entries: 10
      SD card 0 detected, interface speed: 20.0MBytes/sec
      SD card longest block write time: 0.0ms, max retries 0
      MCU temperature: min 101.3, current 110.0, max 110.2
      Supply voltage: min 35.9, current 35.9, max 35.9, under voltage events: 0, over voltage events: 0, power good: no
      Driver 0: ok, SG min/max not available
      Driver 1: ok, SG min/max not available
      Driver 2: ok, SG min/max not available
      Driver 3: ok, SG min/max not available
      Driver 4: ok, SG min/max not available
      Date/time: 1970-01-01 00:00:00
      Cache data hit count 38785090
      Slowest loop: 99.45ms; fastest: 0.05ms
      I2C nak errors 0, send timeouts 0, receive timeouts 0, finishTimeouts 0, resets 0
      === Move ===
      Hiccups: 0, FreeDm: 160, MinFreeDm: 160, MaxWait: 0ms
      Bed compensation in use: none, comp offset 0.000
      === DDARing ===
      Scheduled moves: 0, completed moves: 0, StepErrors: 0, LaErrors: 0, Underruns: 0, 0
      === Heat ===
      Bed heaters = 0 -1 -1 -1, chamberHeaters = 3 -1
      === GCodes ===
      Segments left: 0
      Stack records: 1 allocated, 0 in use
      Movement lock held by null
      http is idle in state(s) 0
      telnet is idle in state(s) 0
      file is idle in state(s) 0
      serial is ready with "M122" in state(s) 0
      aux is idle in state(s) 0
      daemon is idle in state(s) 0
      queue is idle in state(s) 0
      autopause is idle in state(s) 0
      Code queue is empty.
      === Network ===
      Slowest loop: 1.03ms; fastest: 0.00ms
      Responder states: HTTP(0) HTTP(0) HTTP(0) HTTP(0) FTP(0) Telnet(0) Telnet(0)
      HTTP sessions: 0 of 8
      - WiFi -
      Network state is disabled
      WiFi module is disabled
      Failed messages: pending 0, notready 0, noresp 0
      Socket states: 0 0 0 0 0 0 0 0
      ok
      
      
      1 Reply Last reply Reply Quote 0
      • Phaedruxundefined
        Phaedrux Moderator
        last edited by

        How old is the Duet and where was it purchased?

        Z-Bot CoreXY Build | Thingiverse Profile

        1 Reply Last reply Reply Quote 0
        • JairoRBundefined
          JairoRB
          last edited by

          It is about one year old. I would need to contact the sales department for the exact payment date, but I can confirm we received the package on October 18th, 2019. Judging from some emails, it was probably purchased on September 27th, 2019. It was purchased from Filastruder. However, it has been in storage since March, when the pandemic hit. Do you think it got damaged while unused? That would suck, I really hoped it was a software issue.

          1 Reply Last reply Reply Quote 0
          • Phaedruxundefined
            Phaedrux Moderator
            last edited by

            Well it does seem to be a fault in the module. Reflashing the wifi server firmware appears to work correctly, but the error persists.

            Unfortunately you're outside of the 6 month warranty, but we may be able to provide an exchange at reduced cost. Please contact roland@duet3d.com and explain the situation and include a link to this forum thread.

            Alternatively, if you're in a situation where you have access to PCB soldering tools you may be able to replace the wifi module yourself, or have someone do it. The modules themselves can be obtained rather cheaply.

            Z-Bot CoreXY Build | Thingiverse Profile

            1 Reply Last reply Reply Quote 0
            • JairoRBundefined
              JairoRB
              last edited by

              Well, that is unfortunate. I will send an email to that address as you suggested, thank you for the help.

              I do have access to soldering tools. Haven't worked with SMD before, but I have other scrap boards I can practice with before I replace this, or I can ask someone else perhaps. Are there any instructions on how to replace this? As in, specific to the duet? Or do I just find the module itself and solder it back on and then run M122 and that's it?

              Thank you for the help!

              Phaedruxundefined 1 Reply Last reply Reply Quote 0
              • Phaedruxundefined
                Phaedrux Moderator @JairoRB
                last edited by

                @JairoRB said in Error: Failed to initialise WiFi module, code -10 on 2.05:

                Are there any instructions on how to replace this? As in, specific to the duet?

                See here: https://forum.duet3d.com/topic/2825/converting-the-duet-wifi-to-use-an-external-antenna

                That should give you an idea of what's involved to decide if it's a worthwhile option.

                Z-Bot CoreXY Build | Thingiverse Profile

                JairoRBundefined 1 Reply Last reply Reply Quote 0
                • A Former User?
                  A Former User
                  last edited by

                  You might be able to replace the wifi function with a raspberry pi as well, but the required firmware RRF3.2 isn't released yet so it might be a bumpy road.

                  You'd likely not need to remove the Wifi to use the same signals for the SBC interface (depending a little on how the wifi module has failed) lots of details here https://forum.duet3d.com/topic/17203/duet-2-ethernet-and-sbc/

                  This post shows a no-solder approach for the wifi board (albeit a few crimps are needed): https://forum.duet3d.com/post/163005

                  1 Reply Last reply Reply Quote 1
                  • dc42undefined
                    dc42 administrators
                    last edited by dc42

                    Is the DuetWiFiserver.bin file that you uploaded to the WiFi module definitely the DuetWiFiServer.bin file version 1.23 from a recent release?

                    It's worth trying to install the WiFi firmware again. The firmware upload protocol defined by the manufacturer of the WiFi module does not include error detection, and I have known it to appear to succeed but to leave the WiFi module running corrupt firmware.

                    Duet WiFi hardware designer and firmware engineer
                    Please do not ask me for Duet support via PM or email, use the forum
                    http://www.escher3d.com, https://miscsolutions.wordpress.com

                    JairoRBundefined piperswundefined 2 Replies Last reply Reply Quote 0
                    • JairoRBundefined
                      JairoRB @Phaedrux
                      last edited by

                      @Phaedrux that looks great! thanks. I have access to ESP-12E, does that work or does it have to be ESP-12S? I guess I can get an Adafruit HUZZAH or maybe a NodeMCU with the ESP-12S and salvage the module from that board, but if the E version is compatible that would be ideal.

                      A Former User? 1 Reply Last reply Reply Quote 0
                      • A Former User?
                        A Former User @JairoRB
                        last edited by

                        @JairoRB said in Error: Failed to initialise WiFi module, code -10 on 2.05:

                        ESP-12E

                        12E will be fine if the certifications on the module is acceptable for you (fcc/ce/ul etc)

                        JairoRBundefined 1 Reply Last reply Reply Quote 0
                        • JairoRBundefined
                          JairoRB @dc42
                          last edited by

                          @dc42 I am as sure as I think I can be, for what it's worth. I flashed for myself at first from github, then from the link provided by Phaedrux and then again from github, making sure it was indeed version 1.23. After running M997 S1, it completes no problem but the issue comes up.

                          Is there a way to make sure it is the hardware side?

                          1 Reply Last reply Reply Quote 0
                          • JairoRBundefined
                            JairoRB @A Former User
                            last edited by

                            @bearer Excellent, thank you

                            1 Reply Last reply Reply Quote 0
                            • piperswundefined
                              pipersw @dc42
                              last edited by

                              @dc42 said in Error: Failed to initialise WiFi module, code -10 on 2.05:

                              The firmware upload protocol defined by the manufacturer of the WiFi module does not include error detection, and I have known it to appear to succeed but to leave the WiFi module running corrupt firmware

                              I have the issue on two wifi module. I could desolder the module from board and I have some Arduino.
                              How resolve the issue in this case ? (instead of solder the Ethernet module)

                              1 Reply Last reply Reply Quote 0
                              • dc42undefined
                                dc42 administrators
                                last edited by

                                Best option is to replace the WiFi module, assuming you don't want to switch to Ethernet. the recommended modules are ESP12S (internal antenna) and ESP07S (external antenna).

                                Make sure you do not have a M587, M588 or M589 command in config.g. Some users mistakenly put M587 in config.g despite our advice not to. It may cause additional wear on the WiFi module flash memory every time it boots up.

                                Duet WiFi hardware designer and firmware engineer
                                Please do not ask me for Duet support via PM or email, use the forum
                                http://www.escher3d.com, https://miscsolutions.wordpress.com

                                piperswundefined 1 Reply Last reply Reply Quote 0
                                • A Former User?
                                  A Former User
                                  last edited by

                                  (Does the ESP12S have the same antenna improvement the ESP12E allegedly has? Too small sample size to say for sure but 2dBm improvement might be worth while for those replacing it if the certifications aren't an issue)

                                  1 Reply Last reply Reply Quote 0
                                  • piperswundefined
                                    pipersw @dc42
                                    last edited by

                                    @dc42 It's the second module which failed on the board. I will wait my ethernet module for swap now, more reliable

                                    1 Reply Last reply Reply Quote 0
                                    • First post
                                      Last post
                                    Unless otherwise noted, all forum content is licensed under CC-BY-SA