• Tags
  • Documentation
  • Order
  • Register
  • Login
Duet3D Logo Duet3D
  • Tags
  • Documentation
  • Order
  • Register
  • Login

bad bed adhesion on one side after rff3 upgrade

Scheduled Pinned Locked Moved
Tuning and tweaking
kossel bed leveling
4
16
779
Loading More Posts
  • Oldest to Newest
  • Newest to Oldest
  • Most Votes
Reply
  • Reply as topic
Log in to reply
This topic has been deleted. Only users with topic management privileges can see it.
  • undefined
    sungod3k
    last edited by 23 Jan 2021, 21:25

    @Phaedrux said in bad bed adhesion on one side after rff3 upgrade:

    sure 🙂
    homedelta.g config-override.g config.g bed.g FirstLayerTestCircle.gcode M122.txt M98.txt

    http://www.42dimensions.de/
    https://printnewworlds.blogspot.com/

    1 Reply Last reply Reply Quote 0
    • undefined
      Phaedrux Moderator
      last edited by 24 Jan 2021, 00:15

      Do you use mesh compensation? Do you have an example heightmap image? Does it show a tilt?

      Z-Bot CoreXY Build | Thingiverse Profile

      undefined 1 Reply Last reply 24 Jan 2021, 10:34 Reply Quote 0
      • undefined
        sungod3k @Phaedrux
        last edited by 24 Jan 2021, 10:34

        @Phaedrux 2021-01-24 11_24_35-Settings.jpg

        Havent used mesh bed levelling in some time now because it always worked without it.
        I did some test with mesh bed activated, but it didnt make a difference.

        http://www.42dimensions.de/
        https://printnewworlds.blogspot.com/

        1 Reply Last reply Reply Quote 0
        • undefined
          Veti
          last edited by 24 Jan 2021, 10:37

          M308 S0 P"bedtemp" Y"thermistor" T100000 B4138 ; configure sensor 0 as thermistor on pin bedtemp
          M308 S1 P"e0temp" Y"thermistor" T100000 B4138 ; configure sensor 1 as thermistor on pin e0temp

          your thermistor setting is incorrect. find the correct beta value in your thermistor documentation.

          undefined 1 Reply Last reply 25 Jan 2021, 17:37 Reply Quote 0
          • undefined
            Phaedrux Moderator
            last edited by 24 Jan 2021, 18:41

            Can you show the heightmap on a more oblique angle? Dead on makes it hard to see the surface relief.

            Z-Bot CoreXY Build | Thingiverse Profile

            undefined 1 Reply Last reply 25 Jan 2021, 18:23 Reply Quote 0
            • undefined
              wummelfrosch
              last edited by wummelfrosch 24 Jan 2021, 19:16

              which sensor (Z-probe) is used ? maybe this is the fault ? I had such a similar problem with the optical sensor of DC on the green gfk print surface. The values were sometimes good and then again bad and partly implausible ! Only after switching to BlTouch did I have reproducible values.

              1.Modified Prusa Style Printer:Duet2 Eth, 24V MW 750W, E3D Chimera+ Dual Wakü, 2x Bondt QR 500mm Bowden, 2x FTS 2.0 Sensor, BLTouch , 15mm CTC Linear Rails Y-Axis, 2xKGT-12x4 Z-Axis,10mm Linear X-Axis, Laing DDC Pump,120mm Radiator 2.Bcn3d Sigma R19

              undefined 1 Reply Last reply 25 Jan 2021, 17:38 Reply Quote 1
              • undefined
                sungod3k @Veti
                last edited by 25 Jan 2021, 17:37

                @Veti youre right. i corrected the beta, but i dont see a difference in heated behavior

                http://www.42dimensions.de/
                https://printnewworlds.blogspot.com/

                1 Reply Last reply Reply Quote 0
                • undefined
                  sungod3k @wummelfrosch
                  last edited by 25 Jan 2021, 17:38

                  @wummelfrosch i use the smart effector, has served me well so far. and reproducibility is good as far as i can judge it.

                  http://www.42dimensions.de/
                  https://printnewworlds.blogspot.com/

                  undefined 1 Reply Last reply 25 Jan 2021, 18:27 Reply Quote 0
                  • undefined
                    Phaedrux Moderator
                    last edited by 25 Jan 2021, 18:02

                    http://boim.com/DeltaUtil/CalDoc/Calibration.html

                    See if you can identify any issues by comparing your heightmap to these.

                    Z-Bot CoreXY Build | Thingiverse Profile

                    1 Reply Last reply Reply Quote 0
                    • undefined
                      sungod3k @Phaedrux
                      last edited by 25 Jan 2021, 18:23

                      @Phaedrux 2021-01-25 19_22_41-MyDelta.jpg

                      http://www.42dimensions.de/
                      https://printnewworlds.blogspot.com/

                      1 Reply Last reply Reply Quote 0
                      • undefined
                        sungod3k @sungod3k
                        last edited by sungod3k 25 Jan 2021, 18:27

                        @Phaedrux yes, i remember this post. it looks like the examples where one tower is different from the others. but endstop adjustment during g32 should be simple enough, or what could throw off the calibration algo that much?

                        http://www.42dimensions.de/
                        https://printnewworlds.blogspot.com/

                        1 Reply Last reply Reply Quote 0
                        • undefined
                          Phaedrux Moderator
                          last edited by 25 Jan 2021, 18:32

                          I'm afraid that's the extent of my delta knowledge.

                          Best I can suggest is to go through the setup and calibration guides carefully and ensure the build is accurate.

                          https://duet3d.dozuki.com/Wiki/ConfiguringRepRapFirmwareDeltaPrinter
                          https://duet3d.dozuki.com/Wiki/Calibrating_a_delta_printer

                          Overall it appears to be fairly level, but oddly bumpy and maybe bowled a bit.

                          Z-Bot CoreXY Build | Thingiverse Profile

                          1 Reply Last reply Reply Quote 0
                          • undefined
                            Veti
                            last edited by 25 Jan 2021, 18:41

                            that looks a bit like a ripple effect that is caused by backlash.
                            check the belts and pulleys.

                            1 Reply Last reply Reply Quote 0
                            • undefined
                              Phaedrux Moderator
                              last edited by 25 Jan 2021, 18:42

                              Yes maybe backlash. @sungod3k can you provide a screen shot showing an isometric view?

                              Z-Bot CoreXY Build | Thingiverse Profile

                              1 Reply Last reply Reply Quote 0
                              12 out of 16
                              • First post
                                12/16
                                Last post
                              Unless otherwise noted, all forum content is licensed under CC-BY-SA