Duet 3 and connection issues.
-
Web control has insane lag and as you can see its not the wifi speed that is causing it.
Allso trying to set duets ip to static results in a crash and a compleate reset of the board is required to make it work again, what ever i do i cant get the ip to be static.
Any web trafic when the printter is running results in a disconect in web control
Connection established
28.1.2021 klo 16.36.29 Connection interrupted, attempting to reconnect...
HTTP request timed out
28.1.2021 klo 16.36.19 Failed to get file list
Directory 0:/macros not found
28.1.2021 klo 16.36.19 Connection established
28.1.2021 klo 16.36.19 Connection interrupted, attempting to reconnect...
HTTP request timed out
28.1.2021 klo 16.36.00 Failed to get file list
Directory 0:/macros not found
28.1.2021 klo 16.36.00 Connection established
28.1.2021 klo 16.36.00 Connection interrupted, attempting to reconnect...
HTTP request timed out
28.1.2021 klo 16.35.24 Failed to get file list
Directory 0:/macros not found
28.1.2021 klo 16.35.24 Connection established
28.1.2021 klo 16.35.24 Connection interrupted, attempting to reconnect...
HTTP request timed outThis all when typing this message.
-
I see you're having some issues, but we're missing some information to be able to help you.
Are you using the Duet 3 with a raspberry pi, or standalone?
Probably best to start with a standalone setup first.
-
Stand alone, the setup has been functioning fine for a year.
-
Please post the results of M122 and M98 P"config.g"
Post your config.g as well.The duet 3 is wired to your switch/router?
Are you able to set a DHCP reservation on the router for the Duet3? -
M122
=== Diagnostics ===
RepRapFirmware for Duet 3 MB6HC version 3.1.1 running on Duet 3 MB6HC v0.6 or 1.0 (standalone mode)
Board ID: 08DJM-956L2-G43S4-6J1FL-3SJ6T-186QH
Used output buffers: 2 of 40 (23 max)
=== RTOS ===
Static ram: 154604
Dynamic ram: 162784 of which 20 recycled
Exception stack ram used: 376
Never used ram: 75432
Tasks: NETWORK(ready,276) ETHERNET(blocked,404) HEAT(blocked,1112) CanReceiv(suspended,3820) CanSender(suspended,1488) CanClock(blocked,1424) TMC(blocked,196) MAIN(running,4512) IDLE(ready,76)
Owned mutexes:
=== Platform ===
Last reset 00:24:59 ago, cause: power up
Last software reset at 2021-01-29 22:57, reason: User, spinning module GCodes, available RAM 75264 bytes (slot 3)
Software reset code 0x0003 HFSR 0x00000000 CFSR 0x00000000 ICSR 0x0444a000 BFAR 0x00000000 SP 0xffffffff Task MAIN
Error status: 0
MCU temperature: min 23.1, current 23.3, max 23.4
Supply voltage: min 23.6, current 24.0, max 24.1, under voltage events: 0, over voltage events: 0, power good: yes
12V rail voltage: min 12.2, current 12.2, max 12.3, under voltage events: 0
Driver 0: standstill, reads 34723, writes 0 timeouts 0, SG min/max not available
Driver 1: standstill, reads 34723, writes 0 timeouts 0, SG min/max not available
Driver 2: standstill, reads 34722, writes 0 timeouts 0, SG min/max not available
Driver 3: standstill, reads 34723, writes 0 timeouts 0, SG min/max not available
Driver 4: standstill, reads 34722, writes 0 timeouts 0, SG min/max not available
Driver 5: standstill, reads 34722, writes 0 timeouts 0, SG min/max not available
Date/time: 2021-02-04 13:33:09
Slowest loop: 5.13ms; fastest: 0.15ms
=== Storage ===
Free file entries: 10
SD card 0 detected, interface speed: 25.0MBytes/sec
SD card longest read time 3.3ms, write time 0.0ms, max retries 0
=== Move ===
Hiccups: 0(0), FreeDm: 375, MinFreeDm: 375, MaxWait: 0ms
Bed compensation in use: none, comp offset 0.000
=== MainDDARing ===
Scheduled moves: 7, completed moves: 7, StepErrors: 0, LaErrors: 0, Underruns: 0, 0 CDDA state: -1
=== AuxDDARing ===
Scheduled moves: 0, completed moves: 0, StepErrors: 0, LaErrors: 0, Underruns: 0, 0 CDDA state: -1
=== Heat ===
Bed heaters = 0 -1 -1 -1 -1 -1 -1 -1 -1 -1 -1 -1, chamberHeaters = -1 -1 -1 -1
Heater 0 is on, I-accum = 0.7
Heater 1 is on, I-accum = 0.6
=== GCodes ===
Segments left: 0
Movement lock held by null
HTTP is idle in state(s) 0
Telnet is idle in state(s) 0
File is idle in state(s) 0
USB is idle in state(s) 0
Aux is idle in state(s) 0
Trigger is idle in state(s) 0
Queue is idle in state(s) 0
LCD is idle in state(s) 0
SBC is idle in state(s) 0
Daemon is idle in state(s) 0
Aux2 is idle in state(s) 0
Autopause is idle in state(s) 0
Code queue is empty.
=== Network ===
Slowest loop: 5.77ms; fastest: 0.03ms
Responder states: HTTP(0) HTTP(0) HTTP(0) HTTP(0) HTTP(0) HTTP(0) FTP(0) Telnet(0), 0 sessions Telnet(0), 0 sessions
HTTP sessions: 1 of 8- Ethernet -
State: active
Error counts: 0 0 0 0 0
Socket states: 5 2 2 2 2 2 0 2
=== CAN ===
Messages sent 29, longest wait 0ms for type 0
=== Linux interface ===
State: 0, failed transfers: 0
Last transfer: 1499565ms ago
RX/TX seq numbers: 0/1
SPI underruns 0, overruns 0
Number of disconnects: 0
Buffer RX/TX: 0/0-0
- Ethernet -
-
M98 P"config.g"
HTTP is enabled on port 80
FTP is enabled on port 21
TELNET is enabled on port 23
Warning: Heater 0 appears to be over-powered. If left on at full power, its temperature is predicted to reach 465C -
; Configuration file for Duet 3 (firmware version 3)
; executed by the firmware on start-up
;
; generated by RepRapFirmware Configuration Tool v2.1.8 on Fri Apr 10 2020 22:00:06 GMT+0300 (Itä-Euroopan kesäaika); General preferences
G90 ; send absolute coordinates...
M83 ; ...but relative extruder moves
M550 P"Useless junk" ; set printer name; Network
M551 P"Sirsnip1337" ; set password
M552 P0.0.0.0 S1 ; enable network and acquire dynamic address via DHCP
M586 P0 S1 ; enable HTTP
M586 P1 S1 ; enable FTP
M586 P2 S1 ; enable Telnet; Drives
M569 P0.0 S0 ; physical drive 0.0 goes backwards
M569 P0.1 S0 ; physical drive 0.1 goes backwards
M569 P0.2 S1 ; physical drive 0.2 goes forwards
M569 P0.3 S1 ; physical drive 0.3 goes forwards
M584 X0.0 Y0.1 Z0.2 E0.3 ; set drive mapping
M350 X16 Y16 Z16 E16 I1 ; configure microstepping with interpolation
M92 X80.00 Y80.00 Z400.00 E409.00 ; set steps per mm
M566 X900.00 Y900.00 Z12.00 E120.00 ; set maximum instantaneous speed changes (mm/min)
M203 X15600.00 Y15600.00 Z180.00 E3600.00 ; set maximum speeds (mm/min)
M201 X2800.00 Y2800.00 Z100.00 E250.00 ; set accelerations (mm/s^2)
M906 X1100 Y1100 Z1100 E1197 I30 ; set motor currents (mA) and motor idle factor in per cent
M84 S120 ; Set idle timeout; Axis Limits
M208 X0 Y0 Z0 S1 ; set axis minima
M208 X210 Y200 Z300 S0 ; set axis maxima; Endstops
M574 X1 S1 P"io0.in" ; configure active-high endstop for low end on X via pin io0.in
M574 Y1 S1 P"io1.in" ; configure active-high endstop for low end on Y via pin io1.in
M574 Z1 S1 P"io2.in" ; configure active-high endstop for low end on Z via pin io2.in; Z-Probe
M950 S0 C"io7.out" ; create servo pin 0 for BLTouch
M558 P9 C"io7.in" H5 F120 T3000 ; set Z probe type to bltouch and the dive height + speeds
G31 P500 X0 Y41 Z3.0 ; set Z probe trigger value, offset and trigger height
M557 X15:210 Y15:200 S20 ; define mesh grid; Heaters
M308 S0 P"temp0" Y"thermistor" T97700 B4619 C9.743561e-8 ; configure sensor 0 as thermistor on pin temp0
M950 H0 C"out0" T0 ; create bed heater output on out0 and map it to sensor 0
M143 H0 S120 ; set temperature limit for heater 0 to 120C
M307 H0 B0 S1.00 ; disable bang-bang mode for the bed heater and set PWM limit
M140 H0 ; map heated bed to heater 0
M308 S1 P"temp1" Y"thermistor" T100000 B4725 C7.06e-8 ; configure sensor 1 as thermistor on pin temp1
M950 H1 C"out1" T1 ; create nozzle heater output on out1 and map it to sensor 1
M143 H1 S285 ; set temperature limit for heater 1 to 285C
M307 H1 B0 S1.00 ; disable bang-bang mode for heater and set PWM limit; Fans
M950 F0 C"out9" Q10 ; create fan 0 on pin out9 and set its frequency
M106 P0 S0 H-1 ; set fan 0 value. Thermostatic control is turned off
M950 F1 C"out8" Q500 ; create fan 1 on pin out8 and set its frequency
M106 P1 S1 H-1 ; set fan 1 value. Thermostatic control is turned off
M950 F2 C"out7" Q500 ; create fan 2 on pin out7 and set its frequency
M106 P2 S1 H-1 ; set fan 2 value. Thermostatic control is turned off; Tools
M563 P0 S"Hotend/extruder" D0 H1 F0 ; define tool 0
G10 P0 X0 Y0 Z0 ; set tool 0 axis offsets
G10 P0 R0 S0 ; set initial tool 0 active and standby temperatures to 0C; Custom settings are not defined
; Miscellaneous
M501 ; load saved parameters from non-volatile memory
M911 S10 R11 P"M913 X0 Y0 G91 M83 G1 Z3 E-5 F1000" ; set voltage thresholds and actions to run on power loss
T0 ; select first tool -
@Snippy said in Duet 3 and connection issues.:
; Network
M551 P"Sirsnip1337" ; set password
M552 P0.0.0.0 S1 ; enable network and acquire dynamic address via DHCP
M586 P0 S1 ; enable HTTP
M586 P1 S1 ; enable FTP
M586 P2 S1 ; enable TelnetAny modifications made in those result in an inoperable printter.
-
@Phaedrux
Yes its set to static in router. -
When connected to the DWC, upload this zip file to the system tab. Don't extract it first. JUst upload the full zip.
https://github.com/Duet3D/RepRapFirmware/releases/download/3.2/Duet2and3Firmware-3.2.zip
That will update the firmware to 3.2 and refresh the DWC files for 3.2 as well.
I see no errors in your config file
-
Never mind, I see you've started another thread and it looks like you've updated and solved your problem.
