Duet3D Logo Duet3D
    • Tags
    • Documentation
    • Order
    • Register
    • Login

    Makerbot Replicator 2X Duetwifi Edition

    Scheduled Pinned Locked Moved
    My Duet controlled machine
    5
    13
    4.3k
    Loading More Posts
    • Oldest to Newest
    • Newest to Oldest
    • Most Votes
    Reply
    • Reply as topic
    Log in to reply
    This topic has been deleted. Only users with topic management privileges can see it.
    • IdefixRCundefined
      IdefixRC
      last edited by

      My Makerbot Replicators 2x has served me well for many many years. Finally something broke down and it started to reset itself mid print. As replacing all the cables in the machine did not fix the problem I suspected a mainboard or PSU problem. Long story short: it was time for an upgrade.

      The new Replicator 2X now runs a Duetwifi board with reprap firmware, utilizes a IR sensor to measure the bed height and provide mesh bed leveling and displays all the data on a 5'' color touch screen mounted at the same place the old Makerbot display was positioned.

      What did I use for the conversion?

      • 1x Duetwifi Mainboard - http://www.reprap.me/duetwifi-electronics-board.html

      • 1x PanelDue 5'' Display - http://www.reprap.me/paneldue-with-5-screen-for-duetwifi.html

      • 2x M3 Thermistor - http://www.reprap.me/m3-modular-screw-on-stud-thermistor-hot-end-screw-type-thermistors-for-3d-printer.html

      • 1x 24V PSU - http://www.reprap.me/power-supply-24v-15a.html

      • connectors and new cables as I did not want to slaughter the stock makerbot cable set

      Connections:
      Extruder heaters, fans, extruder thermostor, heated bed and bed thermistor connection was straight forward
      Steppers connection was straight forward as well. I simply connected the wires to the board in the same order as you see them on the stepper motor - minus the gap between the pins)
      Endstop connection was done by combining the center 2 pins (these are the ground pins) from the Makerbot endstops to the gnd pin on the Duetwifi 3pin connector. signal and VCC according to the markings on the endstop and duetwifi mainboard
      Zaxis homing was installed with both the makerbot endstop and the IR probe for duetwifi by DC42 (http://www.reprap.me/ir-probe-for-duetwifi.html). As I have some issues with my glass bed and printing ABS as it requires ABS juice which throws the sensor readings off, I currently use the fixed endstop for my prints and will switch back to the IR sensor once my Pei sheet arrives.

      I mounted the board with stand-off to the bottom of the printer in-between the stock makerbot standoffs.4 holes are required in the bottom of the printer for that (M3). I also mounted the PSU beside it at the bottom to get a nice compact installation. There is enough space between PSU and bottom of the printer to allow the cooling fan to ventilate the PSU

      Makerbot LEDs are hooked up to a spare fan connector on the board (plus minus leads only) for it to shine red while in operation. As duet wifi does not have the capacity to control the colors of the RGB LED's I will replace them with white ones going forward.

      Last I removed the old Display and mounted the PanelDue.
      For this I made an enclosure (modification of the enclosure made by DC42) - you can find it here: https://www.thingiverse.com/thing:2428995. It has a few slots to allow storage of SD cards (I still need to purchase the 10pin ribbon cable to actually use the PanelDue SD card slot - would be nice if the panel would come with them btw).

      Finally I configured and tuned the printer with the reprap configurator and by hand with the editor.

      Now I'm enjoying my new, wifi connected, Replicator 🙂

      Update: I have uploaded the IR Sensor mount as well as the config files to thingiverse. The full "Replicator 2X Duet Wifi upgrade series" can be found here:

      • Part 1: DuetWifi Installation and PanelDue Mount (https://www.thingiverse.com/thing:2428995)

      • Part 2: Mini Differential IR Probe mount for Replicator 2X (https://www.thingiverse.com/thing:2475179)

      • Part 3: DuetWifi Configuration files for Replicator 2X (https://www.thingiverse.com/thing:2475257)

      • Part 4: Simplify3D Slicer Configuration for the Replicator 2X (https://www.thingiverse.com/thing:2476695)

      1 Reply Last reply Reply Quote 0
      • Whitewolfundefined
        Whitewolf
        last edited by

        Nice build, congrats!!

        Exploring the universe wherever the tech blows

        1 Reply Last reply Reply Quote 0
        • IdefixRCundefined
          IdefixRC
          last edited by

          Thanks 🙂

          1 Reply Last reply Reply Quote 0
          • T3P3Tonyundefined
            T3P3Tony administrators
            last edited by

            Very cool!

            If you wanted to keep the RGB led outputs then you could use some of the heater pins on the expansion header and small external MOSFETs to switch each colour.

            www.duet3d.com

            1 Reply Last reply Reply Quote 0
            • IdefixRCundefined
              IdefixRC
              last edited by

              Thanks.
              I'm a bit repelled by the price of the expansion board to just drive the LED's 🙂
              Although it would be a nice added bling (maybe the developers could think about a future LED driver/expansion board?) for the printer.

              I will probably stick to the plain white or fix an arduino into the circuit to control the colors (without the gcode integration).

              1 Reply Last reply Reply Quote 0
              • T3P3Tonyundefined
                T3P3Tony administrators
                last edited by

                Yes I would not buy the Duex2 just to drive LEDs ( although of course if you did I would not complain!)

                You can actually use small through hole MOSFETs on a breadboard with a few jumper leads to the requisite pins. It's a bit of work (and looks a bit ghetto) but would achieve the aim.

                www.duet3d.com

                1 Reply Last reply Reply Quote 0
                • Whitewolfundefined
                  Whitewolf
                  last edited by

                  @T3P3Tony:

                  Yes I would not buy the Duex2 just to drive LEDs ( although of course if you did I would not complain!)

                  You can actually use small through hole MOSFETs on a breadboard with a few jumper leads to the requisite pins. It's a bit of work (and looks a bit ghetto) but would achieve the aim.

                  He could also design a working virtual prototype on a virtual bread board and then have a real working PCB addon board shipped to him.

                  Check this out…. the service is free through autodesk you are only charged when ordering the PCB

                  https://circuits.io

                  Exploring the universe wherever the tech blows

                  1 Reply Last reply Reply Quote 0
                  • IdefixRCundefined
                    IdefixRC
                    last edited by

                    Good 🙂 Now I have another project 🙂 In the past I used OSH Park for my PCB creation…....maybe I will cook something up for the BLING 🙂

                    1 Reply Last reply Reply Quote 0
                    • T3P3Tonyundefined
                      T3P3Tony administrators
                      last edited by

                      Even better!

                      www.duet3d.com

                      1 Reply Last reply Reply Quote 0
                      • IdefixRCundefined
                        IdefixRC
                        last edited by

                        Updated the first post. The IR Sensor mount as well as the config files are now available on Thingiverse for download.
                        Print away 🙂

                        1 Reply Last reply Reply Quote 0
                        • makerdiseundefined
                          makerdise
                          last edited by

                          Hey guys,

                          inspired by this, I will start my already heavily modded Rep2x/ MightyBoard RevG to DuetWifi conversion today…
                          I will first do some config and cableworks. As this is a private project, there will be some delays here and there 🙂 😉

                          Like @IdefixRC I am using the parts from carl raffle(carriages, etc.), bottleworks arms/bed and used a custom compiled sailfish version and a filament tracking system - so this setup looks very close to mine. I will also switch to the E3D Aero, the carriage is based on the alumium single carriage from raffle. I am using good LM8SUU bearings.

                          The biggest european Duet3D reseller
                          https://www.makerdise.com

                          1 Reply Last reply Reply Quote 0
                          • makerdiseundefined
                            makerdise
                            last edited by

                            Hey,

                            I finished the beta cable work and got everything running smoove… I could get it managed relatively easy to reactivate the tunell filament monitor. I did grab the +5V/GND from the expansion connector (50pin) while using the E1 endstop signal pin. The tunell got his own logic and a rotary encoder, the monitor is theoretically expensible itself. The E3D Aero is giving real nice results with it's light slimline stepper, there are no more issues related to ghosting. I will have to fix positioning, it's planned that the active cooling will act as kind of a counterbalance. Actually there's to much weight on the right side. I did create all config files by hand in a step by step procedere.

                            Next steps

                            • Active cooling

                            • IR Probe installation

                            • Reactivate the led's

                            • Topmount for 5" display

                            • Mount a new frontpanel

                            • Aluminium sidepanels

                            Cheers
                            Jan

                            The biggest european Duet3D reseller
                            https://www.makerdise.com

                            1 Reply Last reply Reply Quote 0
                            • WalterSKWundefined
                              WalterSKW
                              last edited by

                              @IdefixRC
                              Be carefull with that type of PSU (saw the picture) when you want the full power. They have issues with burning inrush current limiting NTC's….
                              I saw several cases... and I have a 12V one laying around now. Doesn't look that great when you open it...

                              Brian once said: "Always look at the bright side of life"
                              Works for me!

                              1 Reply Last reply Reply Quote 0
                              • First post
                                Last post
                              Unless otherwise noted, all forum content is licensed under CC-BY-SA