Detecting Z-Probe Pickup on move command

fcwilt

@sinned6915 said in Detecting Z-Probe Pickup on move command:

@fcwilt I think you might be right abtou G1 vs. G30 . I think that to meake it work though, I need to redefine the probe to be active LOW so that it beleives its 'triggered' when the circuit comepletes.

So you are determined to make it work using the switch as a probe and doing a while loop?

Frederick

dc42

@sinned6915, if you want to use a G1 command in a while loop with a test to stop movement, you will need to use M400 after the G1 command. Otherwise the G1 commands will be put in the move queue and will not happen instantly. That is why movement continues after the switch is triggered.

Alternatives are to configure the switch as an endstop switch and then use a G1 H1 move; or configure the switch as a Z probe and use a G30 move.

fcwilt

@dc42 said in Detecting Z-Probe Pickup on move command:

Alternatives are to configure the switch as an endstop switch and then use a G1 H1 move; or configure the switch as a Z probe and use a G30 move.

Bless you, good sir. Bless you.

Frederick

sinned6915

@dc42- the many movements filling the que and then clearing it out makes sense.

i think i discovered that by accident earlier too. with really small small steps, like Z=-0.01 it will move and 'softly' pickup the probe and stop.
when I change to a valuue of Z-0.1 i would still overrun it. Then i threw in an M400 and the behavior really changed.

@fcwilt I have been struggling the z-endstop logic all afternoon. as i have tried to show you, I already HAVE the switch set as both endstop and as probe, and I tried using the G1 and G31 commands before I got to this point. I have not doubted you, I just have not ben able to make it work. don't take it peronsally.

M574 Z1 S2 ; configure Z-probe endstop for low end on Z
and
M558 K0 P5 C"^zprobe.in" H8 R0.5 F200 T9000 A1 S0.03

it seems that to make it work, I HAVE to change the probe logic, and that is where I am getting tripped up. it also has to get changed back to probe the bed.

https://duet3d.dozuki.com/Wiki/Gcode#Section_M558_in_RepRapFirmware_Num_3

is where the RRF3 specific stuff was hidden at.

neither method is foolproof. as an engineer my brain is thinking not 'if this bad thing happens' but more 'WHEN this bad thing happens', which will cause the least amount of carnage.

fcwilt

@sinned6915 said in Detecting Z-Probe Pickup on move command:

@fcwilt I have been struggling the z-endstop logic all afternoon. as i have tried to show you, I alrady HAVE the switch set as both endstop and as probe, and I tried using the G1 and G31 commands before I got to this point. I am have not doubted you, I just have not ben able to make it work. don't take it peronsally.

I cannot find the configuration commands that set the switch to be an Z endstop.

Can you guide me to them?

Thanks.

Frederick

fcwilt

@sinned6915 said in Detecting Z-Probe Pickup on move command:

it seems that to make it work, I HAVE to change the probe logic, and that is where I am getting tripped up. it also has to get changed back to probe the bed.

You should not have to do that.

Once the probe displays 1000 in the DWC when it is activated and 0 when it is not you have the correct settings for all uses as a probe.

Unless you have two probes - then you can configure each one separately to obtain the correct values.

Frederick

sinned6915

@fcwilt said in Detecting Z-Probe Pickup on move command:

I cannot find the configuration commands that set the switch to be an Z endstop.

I am reading the command reference for M574. There is a difference in the application in RRF2 an 3.

https://duet3d.dozuki.com/Wiki/Gcode#Section_M574_RepRapFirmware_Num_3

and the Snnn options -

1 = switch-type (eg microswitch) endstop input,
2 = Z probe (when used to home an axis other than Z),
3 = single motor load detection,
4 = multiple motor load detection (see Notes).

M574 says if you use the swtich as active low, invert it by prefixing the pin name with !.
eg: P"!xstop"

RRF3 introduced the C parameter to define the input pin, and the M558 notes for RRF3 says to invert the input, prefix the C with !.
eg: !C

EDIT: The other issue is that the logic and threshold numbers change. Changing the probe type inverts the probe value. I was under the impression that 1000 was high and 0 was low, but it seems to be more realted to the state of the probe.

alt text

fcwilt

@sinned6915 said in Detecting Z-Probe Pickup on move command:

M574 Z1 S2 ; configure Z-probe endstop for low end on Z

You posted this earlier on...

M574 Z1 S2 ; configure Z-probe endstop for low end on Z

From the documentation you pasted...

2 = Z probe (when used to home an axis other than Z),

Notice the other than Z

Again from the documentation you pasted...

1 = switch-type (eg microswitch) endstop input,

To use that switch as an Z endstop you need an M574 like this.

M574 Z1 S1 C"name_of_pin_switch_is_connected_to"

You also may need the ^ and/or ! character to get the endstop state to match the switch state.

Is this switch used for some other purpose - you mention probing the bed? I was thinking this switch was mounted to the frame but it seems it may be mounted to the gantry?

I don't think the same input can be an endstop input and a z probe input at the same time. But I need to verify that. In any case re-configuring it depending on what you need to do that that moment is perfectly fine and not uncommon.

Frederick

sinned6915

@fcwilt i agree with your breakdown of the options and paramters.

Here's the thing though, I gave up trying to migrate my RRF2 setup by hand becasue of all the version changes and choose to use the RRF3 configurator and just start over. I reloaded the .json file and configs that ended up with to make the screenshot.

These were my results and it seemed reasonable, and I have been using it since. I trusted that the configurator was vetted and correct.

The additonal drives that I had to define for Z were later reworked and remapped.

Could there be a mistake in the configurator or in the docs?

alt text

sinned6915

@fcwilt said in Detecting Z-Probe Pickup on move command:

Is this switch used for some other purpose - you mention probing the bed? I was thinking this switch was mounted to the frame but it seems it may be mounted to the gantry?

I am physically (mechanically and electrically) deploying and retracting the switch that is used for probing and z-endstop.

The top half is mounted to the carraige. It has 2 magnets- one is wired to zprobe.in, the other to ground. The LED is wired to Vcc and when the circuit is complete (ie probe picked up)
alt text

The bottom half also has 2 magnets. One magnet is to wired to the Common terminal, the other to the Normally Closed terminal. It acts like a momentary swtich.
alt text

Here are the details if you want to dive in -
https://github.com/nionio6915/Euclid_Probe

fcwilt

@sinned6915

Thank you. That helps tremendously.

So when the top half picks up the bottom have you have a assembly of the two parts with a "push button" on the underside which you can use as a Z probe? Is that correct?

Is they system used to pick up any other kind of bottom half?

Or is it just to have a Z probe that can be installed and removed automatically as needed?

Thanks.

Frederick

fcwilt

@sinned6915 said in Detecting Z-Probe Pickup on move command:

Could there be a mistake in the configurator or in the docs?

There have been mistakes in both in the past.

I don't use the configurator - I rather learn the commands - it makes solving problems easier.

Frederick

sinned6915

I get the behavior that I want with a pickup of the probe and exiting the dock, but the macro seems to loop now and I dont understand why.

alt text

After homing X & Y, trying to home Z seems to deploy the probe correctly using a G1 H1 command. Then the carraige moves to the center of the bed as instreucted in the homez.g files, but at the point where the G30 command is used, the machine appeard to start the deploypobe over. I am confused why it is doing this?

Should I be using a G1 H1 command here instead?

; ***********************************************************
; deployprobe.g
; ***********************************************************
M118 S"deployprobe.g start"
echo sensors.probes[0].value[0]
G91
M564 H0 S0             ; allow movement while not homed
G1 Z15 F6000        ; move Z 10 for clearance above dock.
                    ; need to figure out some safety check on this
G90 

if sensors.probes[0].value[0]!=1000    ; if sensor is value other than 1000 do this
  abort "deployprobe: value0 Probe already picked up.  Manually return probe to the dock"
 
; if we're here we know it's becasue the above is true which I assume is because you have an N0 switch as a probe.

; change probe temporarily to mimic NO to go to NC on pickup
M558 K0 P8 C"^!zprobe.in" H10 R0.5 F200 T9000 A1 S0.03
M118 S"Flipped probe from NC to NO"
echo sensors.probes[0].value[0]
M400

G1 X0 Y0 F6000      ; move above probe dock location
M400                ; wait for moves to finish

G1 H1 Z-280 F300    ; controlled linear move up the height of build envelope
                    ; H1 terminate the move when the endstop switch is triggered
                    ; and set the axis position to the axis limit defined by M208 

G91                 ; relative coords
G1 Z-1 F600       ; move bed up 1 to clear probe from dock since mags pull it up 
M400                ; wait for move to finish
G1 X50 F3000        ; move right so probe moves out of the dock
G1 Z5 F3000         ; move bed to clear probe from glass build surface 
G1 X100 F6000       ;
G90                 ; absolute coords
M400                ; wait for moves to finish

echo sensors.probes[0].value[0]
M558 K0 P8 C"^zprobe.in" H10 R0.5 F200 T9000 A1 S0.03  ; NC synatax
M118 S"Flipped probe from NO to NC"
echo sensors.probes[0].value[0]

G4 S5               ; wait 1 second
; M564 S1             ; limit axis to print area

; while sensors.probes[0].value[0]=1000 ; loop to check when NC probe value changes from 1000 to 0
; while sensors.probes[0].value[0]=0    ; loop to check when N0 probe value changes from 0 to 1000
; if sensors.probes[0].value[0]=0         ; if sensor is value is 0 do this 
                                        ; move bed with probe dock up 0.5mm at a time until the switch activate.  
                                        ; This will get ugly if the switch fails as you have limits off!
;    echo sensors.probes[0].value[0]
;    echo iterations
;    if iterations=1000
;      break

echo sensors.probes[0].value[0]
if sensors.probes[0].value[0]!=0
   abort "deployprobe: endvalue not 0 Probe not picked up!  Print cancelled."

Here is the console output-
alt text

Here are the contents of homez.g-

; ***********************************************************
; homez.g
; ***********************************************************
M118 S"homez.g started"
if !move.axes[0].homed || !move.axes[1].homed     ; If the printer hasn't been homed, home it
   M98 P"0:/sys/homexy.g"  
M561                                            ; clear any bed transform
M290 S0 R0                                      ; clear baby steps per Wes C
G91                                             ; relative positioning
; G1 H2 Z6 F6000                                  ; lift Z relative to current position
G90                                             ; absolute positioning
M401 P0                                         ; This runs macro file deployprobe
G1 X145 Y162.5 F9000                            ; go to first probe point
M400
G30                                             ; home Z by probing the bed
M400
G4 P500
M118 S"Call 4 point macro"
M98 P"0:/sys/bed4point.g"                       ; tram bed
;
G1 X145 Y165 F9000                              ; go back to the first probe point and reprobe 0 in case it moved
G30
M402 P0                                         ; retract probe
G1 Z10 F600                                     ; lift Z relative to current position
G90                                             ; absolute positioning
M564 S1 H0
; G1 X150 Y0 F9000                              ; move carraige to center front

fcwilt

G1 H1 commands are used with endstops. G1 H1 commands have nothing to do with deploying Z probes.

G30 commands are used with a Z probe.

There is no reason I can think of to be using while loops to accomplish your goal.

If you configure the switch device as an Z endstop then a G1 H1 move in the correct direction will stop when the switch is activated.

If you configure the switch device as a Z probe then a G30 command (if it moves toward the switch) will stop when the switch is activated.

The above assumes the switch device is activated with sitting in the dock.

Rather then spend time working with loops why don't you try to get one of the above approaches to work.

You can code some simple macros to test each approach.

Frederick

sinned6915

@fcwilt I am a little confused by your response. I am not using while loops anymore. The test bits of code from earlier are all commented out. I just have not deleted them yet.

I have a G1 H1 Z-280 F300 to pick the switch up from the dock.

Once the switch is picked up from the dock and positioned at the center of the bed, when I issue the G30 command to what I think should be singe point probe to define Z=0.

Instead it seems to start the deployprobe.g macro again. That is what makes no sense to me

Are you saying I should use G1 instead? If that is the case, then how do we take into account the probe offset?

fcwilt

@sinned6915 said in Detecting Z-Probe Pickup on move command:

@fcwilt I am a little confused by your response. I am not using while loops anymore. The test bits of code from earlier are all commented out. I just have not deleted them yet.

Sorry - my bad - I was looking at the commands and didn't notice the bits you had commented out.

I have a G1 H1 Z-280 F300 to pick the switch up from the dock.

This works? Is that switch at that point configured as a Z endstop?

Once the switch is picked up from the dock and positioned at the center of the bed, when I issue the G30 command to what I think should be singe point probe to define Z=0.

Instead it seems to start the deployprobe.g macro again. That is what makes no sense to me

I'm not sure what you mean by "again" - when was it called before this?

The G30 command uses the Z probe. So it calls deployprobe.g before it tries to use it.

And retractprobe.g will be called when the G30 is finished with it.

Is that not happening?

Frederick

OwenD

You shouldn't have the moves to pick up the probe in deployprobe.g
I believe the intent of deployprobe.g is to extend the probe such as when a bltouch or servo probe is used.
As stated above, it is called internally at the start of G30.
If you're manually calling deployprobe.g using M98 and later using G30, then it would do it twice.
Move all that code to say "pickup-probe.g" and likewise put the code to dock the probe into say "dock-probe.g"

fcwilt

@sinned6915

I got to thinking about your homeZ.g file.

You call M401 which invokes deployprobe.g.

Later you call G30 - which normally would call M401 but it seems to notice that M401 has already been called and does not call M401 again. It also does not call M402 as it normally would

Later still you call M402 which invokes retractprobe.g.

Are you invoking deployprobe.g directly using M98 somewhere? G30 does not notice that and invokes M401 calling deployprobe.g as it normally would.

Frederick

dc42

You might want to configure two separate Z probes, one for the real probe and one for the pickup mechanism. RRF3.2 supports this. They can have each have their own deploy and retract files.

sinned6915

@OwenD said in Detecting Z-Probe Pickup on move command:

You shouldn't have the moves to pick up the probe in deployprobe.g
I believe the intent of deployprobe.g is to extend the probe such as when a bltouch or servo probe is used.

That is where I started conceiving this approach. Does the machine really care what it does during the deployprobe?

As stated above, it is called internally at the start of G30.

Any idea where can I confirm this? I'm not distrusting you, I want to re-learn it and maybe re-write the approach I am using.

When I call homez.g, the routine is to pick up the probe via M400, probe Z in the middle of the bed, then probe the 4 corners and level the bed (basically 4-G30 commands, 3 indep motors), then re-probe Z.
The switch is already attached and it does not try to re-deploy the switch.

If you're manually calling deployprobe.g using M98 and later using G30, then it would do it twice.
I'm using M401 and M402 to deploy and retract the probe.

Move all that code to say "pickup-probe.g" and likewise put the code to dock the probe into say "dock-probe.g"

; ***********************************************************
; bed4point.g
; ***********************************************************
 G90
 G30 P0 X0.0 Y5.0 F9000.0 Z-99999       ; probe front left
 G30 P1 X0.0 Y275.0 F9000.0 Z-99999     ; probe back left
 G30 P2 X270.0 Y275.0 F9000.0 Z-99999   ; probe back right
 G30 P3 X270.0 Y5.0 F9000.0 Z-99999 S3  ; probe near front right leadscrew and calibrate 3 motors