Error: Attempting to extrude with no tool selected

droftarts

@sgk Try moving the 'Tool' section of your config.g to after the fan definitions. At the moment it is defining the tool with a fan (F1, which is the thermostatic hot end fan, so I think it should be F0, the tool fan) before the fan has been defined. This wasn't a problem in the old version of the firmware, as fans were defined by default, but in RRF3 there are no default definitions.

Ian

A Former User

hello everyone thank you very much for all of your help.
I post my gcode

https://drive.google.com/drive/folders/1ryDNZchhWtu0Z5FudB5cCDygz8ms5czn?usp=sharing

A Former User

for info I disconnected my panelduo and I managed to print
1 time

Veti

@sgk
ok see if you can route the paneldue cable not near any power or stepper cables

A Former User

thank you but I have more panelduo because it no longer works the touch
so i will see if it works now permanently

Phaedrux

G90
M82
M106 S255
G4 P500
M106 S191
M140 S60
M190 S60
M104 S200 T0
M109 S200 T0
M291 P"Homing all axis" R"Printing.." S1 T2
G21		; metric values
G28		; home all
;G29 S2		; mark if you want to disable mesh grid
G32		; Run mesh grid compenstion
		; Purge extruder
G92 E0 F100		; reset extruder
G1 Z10 F3000 		; move z up little to prevent scratching of surface
M98 P/macros/Filament/Purge	; Run nozzle purge macro
;G1 E-1 F2000		; Retract 1mm filament
G92 E0 		; reset extruder
M291 P"Printing started !" R"Printing.." S1 T3
; process Process1
; layer 1, Z = 0.120
T0
G92 E0.0000
G1 E-6.0000 F2400
; feature inner perimeter
; tool H0.120 W0.480

What do you have in macro here: M98 P/macros/Filament/Purge ; Run nozzle purge macro

What do you have in bed.g?

What do you have in homeall.g?

A Former User

hello
; bed.g
; called to perform automatic bed compensation via G32
;
; generated by RepRapFirmware Configuration Tool on Tue Oct 09 2018 13:27:56 GMT+0300
M291 P"Probing mesh grid process started" R"Probing.." S1 T2
M561 ; clear any bed transform
G28 ; home all axis bb
M671 X-55.0:364.0 Y175.0:175.0 S5.0
G30 P1 X5 Y150 Z-99999
G30 P0 X300 Y150 Z-99999 S2
G90 ; absolute positioning bb
M557 X20:270 Y20:270 S240 ; Define mesh grid
G29 S0 ; Probe the bed and save height map to file
M374 ; Save calibration data. Default is sys/heightmap.csv
M291 P"Probing mesh grid process finished !" R"Probing.." S1 T2
; Probe the bed at 4 points
;G30 P0 X10 Y10 H0 Z-99999
;G30 P1 X10 Y290 H0 Z-99999
;G30 P2 X290 Y290 H0 Z-99999
;G30 P3 X290 Y10 H0 Z-99999 S

A Former User

; homeall.g
; called to home all axes
;
; generated by RepRapFirmware Configuration Tool on Tue Oct 09 2018 13:27:56 GMT+0300
G91 ; relative positioning
G1 H2 Z5 F6000 S2 ; lift Z relative to current position
G1 H1 X-355 Y355 F6000 ; move quickly to X or Y endstop and stop there (first pass)
G1 H1 X-355 ; home X axis
G1 H1 Y355 ; home Y axis
G1 X5 Y-5 F6000 ; go back a few mm
G1 H1 X-355 F360 ; move slowly to X axis endstop once more (second pass)
G1 H1 Y355 ; then move slowly to Y axis endstop
G90 ; absolute positioning
G1 X152 Y166.4 F6000 ; go to first bed probe point and home Z
G30 ; home Z by probing the bed

; Uncomment the following lines to lift Z after probing
;G91 ; relative positioning
;G1 S2 Z5 F100 ; lift Z relative to current position
;G90 ; absolute positioning

A Former User

;purge hotend
M291 P"purge started !" R"purging.." S1 T2 ; display msg
G1 Z10 F3000 ; move z up little to prevent scratching of surface
G1 X5 Y70 Z0.3 F5000.0 ; move to start-line position
G1 Z0.3 F1000 ; print height
G1 X5 Y220 F1500.0 E15 ; draw 1st line
G1 X5.2 Y220 Z0.3 F5000.0 ; move to side a little
G1 X5.2 Y70 Z0.3 F1500.0 E30 ; draw 2nd line
;G1 E-1 F2000 ; Retract 1mm filament
G1 Z10 F3000 ; move z up little to prevent scratching of surface
G1 X150 Y150 F6000 ; move to center of the bed
M291 P"purge finished !" R"purging.." S1 T2 ; display msg

A Former User

; Clean nozzle macro
M291 P"Cleaning Hotend" R"Cleaning.." S1 T5 ; display msg
G1 Z10 F3000 ; move z up little to prevent scratching of surface
G1 X-20 Y290 F10000 ; move to first brush point
G1 Z0.5 F3000 ; lower nozzle to the brush
G1 X-8 Y290 F10000 ;
G1 X-20 Y290 F10000 ; move back to first brush point
G1 X-8 Y280 F10000 ; move to 2 brush point
G1 X-20 Y280 F10000 ; move to 2 brush point
G1 X-8 Y280 F10000 ; move back to 2 brush point
G1 X-20 Y270 F10000 ; move back to 3 brush point
G1 X-8 Y270 F10000 ; move back to 3 brush point
G1 X-20 Y270 F10000 ; move back to 3 brush point
G1 X-8 Y260 F10000 ; move back to 4 brush point
G1 X-20 Y260 F10000 ; move back to 4 brush point
G1 X-8 Y260 F10000 ; move back to 4 brush point
G1 X-20 Y254 F10000 ; move back to 5 brush point
G1 X-8 Y254 F10000 ; move back to 5 brush point
G1 Z10 F3000 ; move z up little to prevent scratching of surface
M291 P"Cleaning finished !" R"Cleaning...." S1 T2 ; display msg