Duet3D Logo Duet3D
    • Tags
    • Documentation
    • Order
    • Register
    • Login

    Need help to fix this

    Scheduled Pinned Locked Moved
    General Discussion
    5
    16
    1.6k
    Loading More Posts
    • Oldest to Newest
    • Newest to Oldest
    • Most Votes
    Reply
    • Reply as topic
    Log in to reply
    This topic has been deleted. Only users with topic management privileges can see it.
    • Jackalundefined
      Jackal
      last edited by

      Can you provide a gcode file up to part of the first layer? and also your config.g

      1 Reply Last reply Reply Quote 0
      • tapeundefined
        tape
        last edited by

        ok just tested with a gcode with no retraction and it works fine.

        how can i fix the retraction?

        1 Reply Last reply Reply Quote 0
        • dc42undefined
          dc42 administrators
          last edited by

          Yes, please share the gcode file.

          Duet WiFi hardware designer and firmware engineer
          Please do not ask me for Duet support via PM or email, use the forum
          http://www.escher3d.com, https://miscsolutions.wordpress.com

          1 Reply Last reply Reply Quote 0
          • tapeundefined
            tape
            last edited by

            https://drive.google.com/file/d/0Bx0mLwkx-u8vdDctbEdvRUhvRTQ/view?usp=sharing

            1 Reply Last reply Reply Quote 0
            • Jackalundefined
              Jackal
              last edited by

              What are your extruder speed and acceleration settings in your config.g?

              1 Reply Last reply Reply Quote 0
              • tapeundefined
                tape
                last edited by

                M906 X800 Y800 Z800 E1000 ; Set motor currents (mA)
                M201 X800 Y800 Z15 E400 ; Accelerations (mm/s^2)
                M203 X15000 Y15000 Z240 E100 ; Maximum speeds (mm/min)
                M566 X600 Y600 Z30 E20 ; Minimum speeds mm/minute
                M208 X200 Y175 Z180 ; set axis maxima (adjust to suit your machine)
                M208 X0 Y0 Z-0.2 S1 ; set axis minimum (adjust to make X=0 and Y=0 the edge of the bed)
                M92 X80 Y80 Z4000 ; Set axis steps/mm
                M92 E100:100

                1 Reply Last reply Reply Quote 0
                • dc42undefined
                  dc42 administrators
                  last edited by

                  The problem is that you have set your maximum extruder speed to 100mm/min in the M203 command. That is very low and it is making retractions very slow. A more typical value would be 3000 to 6000 mm/min.

                  Duet WiFi hardware designer and firmware engineer
                  Please do not ask me for Duet support via PM or email, use the forum
                  http://www.escher3d.com, https://miscsolutions.wordpress.com

                  1 Reply Last reply Reply Quote 0
                  • tapeundefined
                    tape
                    last edited by

                    thanks

                    1 Reply Last reply Reply Quote 0
                    • tapeundefined
                      tape
                      last edited by

                      problem solved. thanks again

                      1 Reply Last reply Reply Quote 0
                      • FrankNPrinterundefined
                        FrankNPrinter
                        last edited by

                        I had mine set at 1300 and was getting under extrudes at speed. Didn't even know i had this issues till i checked. Thanks dc42, you got a 2 for 1 on this solution 🙂

                        1 Reply Last reply Reply Quote 0
                        • number40fanundefined
                          number40fan
                          last edited by

                          3 for 1. 1200 here. Getting bumped up.

                          Edit: Huge difference. I have been fighting layer issues and this was the fix. Looked up what the stock printer board was set to (9000) and changed it to that.

                          1 Reply Last reply Reply Quote 0
                          • First post
                            Last post
                          Unless otherwise noted, all forum content is licensed under CC-BY-SA