Ender 5 plus - I need help

Kanzleralexander · 3 Mar 2021, 23:16

Configuration file for Duet 3 (firmware version 3)
; executed by the firmware on start-up
;
; generated by RepRapFirmware Configuration Tool v3.2.3 on Wed Mar 03 2021 22:50:58 GMT+0100 (Mitteleuropäische Normalzeit)

; General preferences
G90 ; send absolute coordinates...
M83 ; ...but relative extruder moves
M550 P"Duet 3" ; set printer name

; Drives
M569 P0.0 S0 ; physical drive 0.0 goes backwards
M569 P0.1 S0 ; physical drive 0.1 goes backwards
M569 P0.2 S0 ; physical drive 0.2 goes backwards
M569 P0.3 S0 ; physical drive 0.3 goes backwards
M584 X0.0 Y0.1 Z0.2 E0.3 ; set drive mapping
M350 X32 Y32 Z32 E128 I0 ; configure microstepping without interpolation
M92 X80.00 Y80.00 Z400.00 E420.00 ; set steps per mm
M566 X900.00 Y900.00 Z60.00 E300.00 ; set maximum instantaneous speed changes (mm/min)
M203 X6000.00 Y6000.00 Z180.00 E1200.00 ; set maximum speeds (mm/min)
M201 X3000.00 Y3000.00 Z60.00 E250.00 ; set accelerations (mm/s^2)
M906 X800 Y800 Z800 E800 I30 ; set motor currents (mA) and motor idle factor in per cent
M84 S30 ; Set idle timeout

; Axis Limits
M208 X0 Y0 Z0 S1 ; set axis minima
M208 X350 Y350 Z400 S0 ; set axis maxima

; Endstops
M574 X2 S1 P"!io0.in" ; configure active-high endstop for high end on X via pin !io0.in
M574 Y2 S1 P"!io1.in" ; configure active-high endstop for high end on Y via pin !io1.in
M574 Z2 S2 ; configure Z-probe endstop for high end on Z

; Z-Probe
M950 S0 C"io4.out" ; create servo pin 0 for BLTouch
M558 P9 C"^io3.in" H5 F1800 T6000 ; set Z probe type to bltouch and the dive height + speeds
G31 P500 X-44 Y-9 Z2.09 ; set Z probe trigger value, offset and trigger height
M557 X10:350 Y10:350 S20 ; define mesh grid

; Heaters
M308 S0 P"temp0" Y"thermistor" T988801 B4185 C2200 ; configure sensor 0 as thermistor on pin temp0
M950 H0 C"out0" T0 ; create bed heater output on out0 and map it to sensor 0
M307 H0 B1 S1.00 ; enable bang-bang mode for the bed heater and set PWM limit
M140 H0 ; map heated bed to heater 0
M143 H0 S110 ; set temperature limit for heater 0 to 110C
M308 S1 P"temp1" Y"thermistor" T98801 B4185 C2200 ; configure sensor 1 as thermistor on pin temp1
M950 H1 C"out1" T1 ; create nozzle heater output on out1 and map it to sensor 1
M307 H1 B0 S1.00 ; disable bang-bang mode for heater and set PWM limit
M143 H1 S260 ; set temperature limit for heater 1 to 260C

; Fans
M950 F0 C"out6" Q20 ; create fan 0 on pin out6 and set its frequency
M106 P0 S1 H0 T45 ; set fan 0 value. Thermostatic control is turned on
M950 F1 C"out7" Q20 ; create fan 1 on pin out7 and set its frequency
M106 P1 S1 H1 T45 ; set fan 1 value. Thermostatic control is turned on
M950 F2 C"out8" Q20 ; create fan 2 on pin out8 and set its frequency
M106 P2 S1 H1 T45 ; set fan 2 value. Thermostatic control is turned on

; Tools
M563 P0 H1 F0 ; define tool 0
G10 P0 X0 Y0 Z0 ; set tool 0 axis offsets
G10 P0 R0 S0 ; set initial tool 0 active and standby temperatures to 0C

; Custom settings are not defined

; Miscellaneous
M575 P1 S1 B57600 ; enable support for PanelDue
M501 ; load saved parameters from non-volatile memory
M911 S21 R23 P"M913 X0 Y0 G91 M83 G1 Z3 E-5 F1000" ; set voltage thresholds and actions to run on power loss
T0 ; select first tool
~~strikethrough text~~

Kanzleralexander · 3 Mar 2021, 23:18

This post is deleted!

Kanzleralexander · 3 Mar 2021, 23:24

@Kanzleralexander Fans and BLTOUCH -Do not work
Is configuration correct?

Phaedrux · 4 Mar 2021, 00:20

Can you provide the results of M122 and M98 P"config.g"? That would give us a good starting place.

There are some guides for using a duet with the Ender 3 that may be helpful to you. The Ender 3 and 5 are quite close.

https://duet3d.dozuki.com/Search?query=ender+3

@Kanzleralexander said in Ender 5 plus - I need help:

; Fans
M950 F0 C"out6" Q20 ; create fan 0 on pin out6 and set its frequency
M106 P0 S1 H0 T45 ; set fan 0 value. Thermostatic control is turned on
M950 F1 C"out7" Q20 ; create fan 1 on pin out7 and set its frequency
M106 P1 S1 H1 T45 ; set fan 1 value. Thermostatic control is turned on
M950 F2 C"out8" Q20 ; create fan 2 on pin out8 and set its frequency
M106 P2 S1 H1 T45 ; set fan 2 value. Thermostatic control is turned on

The part cooling fan probably doesn't work because it's set to be thermostatically controlled to turn on at 45c.

Change this M106 P0 S1 H0 T45 to M106 P0 S1 H-1

what exactly doesn't work with the bltouch?

Kanzleralexander · 3 Apr 2021, 00:36

@Phaedrux my code:

Endstops
M574 X2 S1 P"!io0.in" ; configure active-high endstop for high end on X via pin !io0.in
M574 Y2 S1 P"!io1.in" ; configure active-high endstop for high end on Y via pin !io1.in
M574 Z2 S2 ; configure Z-probe endstop for high end on Z

; Z-Probe
M950 S0 C"io4.out" ; create servo pin 0 for BLTouch
M558 P9 C"^io3.in" H5 F1800 T6000 ; set Z probe type to bltouch and the dive height + speeds
G31 P500 X-44 Y-9 Z2.09 ; set Z probe trigger value, offset and trigger height
M557 X10:350 Y10:350 S20 ; define mesh grid

And i find in Internet for Ender 5 :

Endstops
M574 Z0 ; disabled end stop for z
M574 X2 Y2 S1 ; set active high endstops

; Filament Sensor
M591 D0 P1 S1 C3

; Z-Probe
M307 H3 A-1 C-1 D-1 ; disable heater on PWM channel for BLTouch
M558 P9 H5 F120 T6000 ; set Z probe type to bltouch and the dive height + speeds
G31 P500 X-44 Y-9 Z2.09 ; set Z probe trigger value, offset and trigger height
M557 X60:300 Y30:300 S30

Kanzleralexander · 4 Mar 2021, 00:38

; Fans
M106 P0 C"part-cooling" S0.65 I0 F500 H-1 ; set fan 0 name, value, PWM signal inversion and frequency. Thermostatic control is turned off
M106 P1 C"hotend" S0.65 I0 F500 H1 T100 ; set fan 1 name, value, PWM signal inversion and frequency. Thermostatic control is turned on
M106 P2 S0.85 I0 F500 H-1

Phaedrux · 4 Mar 2021, 01:15

@Kanzleralexander said in Ender 5 plus - I need help:

And i find in Internet for Ender 5 :
Endstops
M574 Z0 ; disabled end stop for z
M574 X2 Y2 S1 ; set active high endstops
; Filament Sensor
M591 D0 P1 S1 C3
; Z-Probe
M307 H3 A-1 C-1 D-1 ; disable heater on PWM channel for BLTouch
M558 P9 H5 F120 T6000 ; set Z probe type to bltouch and the dive height + speeds
G31 P500 X-44 Y-9 Z2.09 ; set Z probe trigger value, offset and trigger height
M557 X60:300 Y30:300 S30

That's for firmware 2.x your current config is for the more recent version 3 firmware.

@Kanzleralexander said in Ender 5 plus - I need help:

M106 P1 C"hotend" S0.65 I0 F500 H1 T100 ; set fan 1 name, value, PWM signal inversion and frequency. Thermostatic control is turned on

T100 mena sit won't turn the hot end heat sink fan until it's 100c which is hot enough to cause jamming. T45 is a better choice.

Phaedrux · 4 Mar 2021, 01:16

@Phaedrux said in Ender 5 plus - I need help:

Can you provide the results of M122 and M98 P"config.g"? That would give us a good starting place.

Please provide this so we can see what firmware you're actually using.

Kanzleralexander · 4 Mar 2021, 01:48

sys\config.g

Kanzleralexander · 4 Mar 2021, 01:49

Configuration file for Duet 3 (firmware version 3)
; executed by the firmware on start-up
;
; generated by RepRapFirmware Configuration Tool v3.2.3 on Thu Mar 04 2021 02:49:06 GMT+0100 (Mitteleuropäische Normalzeit)

; General preferences
G90 ; send absolute coordinates...
M83 ; ...but relative extruder moves
M550 P"My Printer" ; set printer name

; Network
M552 P0.0.0.0 S1 ; enable network and acquire dynamic address via DHCP
M586 P0 S1 ; enable HTTP
M586 P1 S0 ; disable FTP
M586 P2 S0 ; disable Telnet

; Drives
M569 P0.0 S0 ; physical drive 0.0 goes backwards
M569 P0.1 S0 ; physical drive 0.1 goes backwards
M569 P0.2 S0 ; physical drive 0.2 goes backwards
M569 P0.3 S0 ; physical drive 0.3 goes backwards
M584 X0.0 Y0.1 Z0.2 E0.3 ; set drive mapping
M350 X32 Y32 Z32 E128 I0 ; configure microstepping without interpolation
M92 X80.00 Y80.00 Z400.00 E420.00 ; set steps per mm
M566 X900.00 Y900.00 Z60.00 E60.00 ; set maximum instantaneous speed changes (mm/min)
M203 X6000.00 Y6000.00 Z180.00 E1200.00 ; set maximum speeds (mm/min)
M201 X3000.00 Y3000.00 Z20.00 E250.00 ; set accelerations (mm/s^2)
M906 X800 Y800 Z800 E800 I30 ; set motor currents (mA) and motor idle factor in per cent
M84 S30 ; Set idle timeout

; Axis Limits
M208 X0 Y0 Z0 S1 ; set axis minima
M208 X350 Y350 Z400 S0 ; set axis maxima

; Endstops
M574 X2 S1 P"io0.in" ; configure active-high endstop for high end on X via pin io0.in
M574 Y2 S1 P"io1.in" ; configure active-high endstop for high end on Y via pin io1.in
M574 Z2 S2 ; configure Z-probe endstop for high end on Z

; Z-Probe
M950 S0 C"io4.out" ; create servo pin 0 for BLTouch
M558 P9 C"^io3.in" H5 F1800 T6000 ; set Z probe type to bltouch and the dive height + speeds
G31 P500 X-44 Y-9 Z29 ; set Z probe trigger value, offset and trigger height
M557 X10:350 Y10:350 S20 ; define mesh grid

; Heaters
M308 S0 P"temp0" Y"thermistor" T988801 B4185 C2200 ; configure sensor 0 as thermistor on pin temp0
M950 H0 C"out0" T0 ; create bed heater output on out0 and map it to sensor 0
M307 H0 B1 S1.00 ; enable bang-bang mode for the bed heater and set PWM limit
M140 H0 ; map heated bed to heater 0
M143 H0 S110 ; set temperature limit for heater 0 to 110C
M308 S1 P"temp1" Y"thermistor" T98801 B4185 C2200 ; configure sensor 1 as thermistor on pin temp1
M950 H1 C"out1" T1 ; create nozzle heater output on out1 and map it to sensor 1
M307 H1 B0 S1.00 ; disable bang-bang mode for heater and set PWM limit
M143 H1 S260 ; set temperature limit for heater 1 to 260C

; Fans
M950 F0 C"out6" Q20 ; create fan 0 on pin out6 and set its frequency
M106 P0 S0 H-1 ; set fan 0 value. Thermostatic control is turned off
M950 F1 C"out7" Q20 ; create fan 1 on pin out7 and set its frequency
M106 P1 S1 H1 T45 ; set fan 1 value. Thermostatic control is turned on
M950 F2 C"out8" Q20 ; create fan 2 on pin out8 and set its frequency
M106 P2 S1 H1:0 T45 ; set fan 2 value. Thermostatic control is turned on

; Tools
M563 P0 D0 H1 F0 ; define tool 0
G10 P0 X0 Y0 Z0 ; set tool 0 axis offsets
G10 P0 R0 S0 ; set initial tool 0 active and standby temperatures to 0C

; Custom settings are not defined

; Miscellaneous
M575 P1 S1 B57600 ; enable support for PanelDue
M501 ; load saved parameters from non-volatile memory

Phaedrux · 4 Mar 2021, 02:57

Send M122 and M98 P"config.g" in the gcode console tab and post the results.

Also please describe what isn't working.

Veti · 4 Mar 2021, 05:50

@Kanzleralexander said in Ender 5 plus - I need help:

M350 X32 Y32 Z32 E128 I0 ; configure microstepping without interpolation
M92 X80.00 Y80.00 Z400.00 E420.00 ; set steps per mm

the steps you configured are for x16 microstepping