Duet3D Logo Duet3D
    • Tags
    • Documentation
    • Order
    • Register
    • Login

    Preview version of CNC optimized DWC.

    Scheduled Pinned Locked Moved
    CNC
    40
    191
    22.1k
    Loading More Posts
    • Oldest to Newest
    • Newest to Oldest
    • Most Votes
    Reply
    • Reply as topic
    Log in to reply
    This topic has been deleted. Only users with topic management privileges can see it.
    • weed2allundefined
      weed2all @chimaeragh
      last edited by

      @chimaeragh did you put it in cnc mode...if not will show the 3d printer interface!

      https://www.thingiverse.com/weed2all/designs

      chimaeraghundefined 1 Reply Last reply Reply Quote 1
      • chimaeraghundefined
        chimaeragh @weed2all
        last edited by

        @weed2all Yes I did. It is showing the CNC interface but there are still remnants of 3D printing like extruders, filaments and temperature which are not useful in a CNC environment. If you have used Ooznest's Workbee Control before you will understand what I mean.

        Duet 2 Wifi, Ooznest Workbee CNC 1510

        Sindariusundefined 1 Reply Last reply Reply Quote 0
        • Sindariusundefined
          Sindarius @chimaeragh
          last edited by

          @chimaeragh would you mind sharing some screenshots of the items you are referring to. Just an fyi the main areas of this version are focused on the dashboard and some plugins.

          chimaeraghundefined 1 Reply Last reply Reply Quote 0
          • chimaeraghundefined
            chimaeragh @Sindarius
            last edited by

            @Sindarius I was referring to areas other than the dashboard. If this release is mainly about the dashboard then I have no complaints. Thanks

            Duet 2 Wifi, Ooznest Workbee CNC 1510

            Sindariusundefined 1 Reply Last reply Reply Quote 0
            • Sindariusundefined
              Sindarius @chimaeragh
              last edited by

              @chimaeragh at this point the only area addressed outside of plugins is the dashboard. I know areas such as files need to be addressed. However, dashboard functionality was the main initial target.

              1 Reply Last reply Reply Quote 1
              • UcantCNCmeundefined
                UcantCNCme @Sindarius
                last edited by

                This post is deleted!
                1 Reply Last reply Reply Quote 0
                • Shanian79undefined
                  Shanian79
                  last edited by

                  Just following up on this. I've been running my CNC on a Duet3 board for a couple months now and loving it! Thanks to all who put the time and effort into this project!

                  https://drive.google.com/file/d/1IoRxP0r1AkXaKeTeyZBixeCDPX-JHSoq/view?usp=sharing

                  IMG_2361.jpg
                  IMG_2360.jpg

                  1 Reply Last reply Reply Quote 3
                  • Yveskeundefined
                    Yveske
                    last edited by Yveske

                    @sindarius Is it possible to have the probe status back please ?

                    crossbowundefined 1 Reply Last reply Reply Quote 1
                    • Hagridundefined
                      Hagrid @Sindarius
                      last edited by

                      @sindarius - Firstly, what you have produced so far is BRILLIANT!! Well done sir 🙂 I absolutely love it!!

                      Secondly - have you had any time to look into / work on, the idea of a plugin for the XYZ probe used on the Workbee? The DWC used by Ooznest was great for the inclusion of the automated probe setup/use, but the rest of the UI was so heavily "printer based" that I hated it.

                      Your CNC version, is "the dog's wotsits". If "their" probe setup (or similar) could be added to "yours" as a plugin - SO many people would be extremely pleased.

                      Thoughts - for future development ........., your gcode viewer is good. Before having to use/learn Duet, I used Universal Gcode Sender - the feature that I love in that, is seeing the toolpaths, and a representation of the tool tip - in real time as the cut progresses. It certainly gives me reassurance as to what the machine is doing/about to do. So a possible plugin for that would be uber cool!!!!

                      Many thanks - keep up your great work 🙂

                      rilotundefined 1 Reply Last reply Reply Quote 3
                      • rilotundefined
                        rilot @Hagrid
                        last edited by

                        @hagrid I've made some macros to deal with the xyz probe. Just need to edit for your different tool widths. I mainly use 6mm and 3mm end-mills so this works fine for me at the moment to have 2 macros. If I have an oddball sized bit then it's only 10 seconds to adjust the macro.
                        Admittedly, it would be lovely to have the Workbee style probe as a plugin but for the minute, the benefits of the newer firmware and this DWC outweigh the loss of the probe functions.

                        If you want me to post the macros I can do so tomorrow when I'm in the workshop.

                        chimaeraghundefined weed2allundefined Hagridundefined 3 Replies Last reply Reply Quote 1
                        • chimaeraghundefined
                          chimaeragh @rilot
                          last edited by

                          @rilot Please do post your macros.

                          Duet 2 Wifi, Ooznest Workbee CNC 1510

                          1 Reply Last reply Reply Quote 0
                          • weed2allundefined
                            weed2all @rilot
                            last edited by

                            @rilot yes of course please post the macros!

                            https://www.thingiverse.com/weed2all/designs

                            1 Reply Last reply Reply Quote 0
                            • Hagridundefined
                              Hagrid @rilot
                              last edited by

                              @rilot that would be greatly appreciated - many thanks 🙂

                              rilotundefined 1 Reply Last reply Reply Quote 0
                              • rilotundefined
                                rilot @Hagrid
                                last edited by

                                @hagrid @chimaeragh Completely forgot to post the macros.

                                Here you go:

                                Z probe:

                                M291 P"Make sure the probe is connected and is in position." R"Warning" S3
                                G91
                                M563 P49 S"XYZ-Probe"
                                T49
                                ; M585 Z10 E4 L0 F250 S1
                                M585 Z10 P1 F250 S1
                                M400
                                G10 L20 Z4.72 ; Adjust this to match the thickness of your touch plate
                                G1 Z5 F250
                                G90
                                M291 P"Probe complete. Please remove probe." R"Success" S1
                                

                                XYZ probe with 8mm bit

                                M291 P"Make sure the probe is connected and is in position." R"Warning" S3
                                G91
                                ; M563 P49 S"XYZ-Probe"
                                ;T49
                                T1
                                G1 X20 Y20 F500
                                ; M585 Z10 P1 F250 S1
                                M585 Z50 P1 F250 S1
                                G10 P1 X0 Y0 Z0
                                G10 P2 L20 Z4.72 ;Please adjust the Z value here to match the thickness of your touchplate.
                                G1 Z3 F500
                                G1 X-50 F500
                                G1 Z-5.5 F500
                                M585 X50 P1 F250 S0
                                G10 P1 X0 Y0 Z0
                                G10 P2 L20 X-19.3 ;Please adjust the X value to match the X thickness of your touch plate + the radius of the your endmill. Make it negative.
                                G1 X-3 F500
                                G1 Z5.5 F500
                                G1 X50 F500
                                G1 Y-50 F500
                                G1 Z-5.5 F500
                                M585 Y50 P1 F250 S0
                                G10 P1 X0 Y0 Z0
                                G10 P2 L20 Y-19 ;Please adjust the Y value to match the Y thickness of your touch plate + the radius of the your endmill. Make it negative.
                                G1 Y-3 F500
                                M500
                                T0
                                G90
                                G55
                                G1 Z8 F500
                                G1 X0 Y0 F500
                                M291 P"Probe complete. Please remove probe." R"Success" S1
                                
                                chimaeraghundefined Hagridundefined 3 Replies Last reply Reply Quote 3
                                • chimaeraghundefined
                                  chimaeragh @rilot
                                  last edited by

                                  @rilot Thanks.

                                  Duet 2 Wifi, Ooznest Workbee CNC 1510

                                  1 Reply Last reply Reply Quote 0
                                  • chimaeraghundefined
                                    chimaeragh @rilot
                                    last edited by

                                    @edwardp Can you have a look at this macro and see if it works for your implementation?

                                    Duet 2 Wifi, Ooznest Workbee CNC 1510

                                    edwardpundefined 1 Reply Last reply Reply Quote 0
                                    • edwardpundefined
                                      edwardp @chimaeragh
                                      last edited by

                                      @chimaeragh thanks for posting those. I am just working through the simplest Z-only probe initially (@Kane on the other thread has a version of the macro that is now working for me). Once we have the Z probe working reliably (and I understand the subtleties of why my original macro was incorrect) I will use these to explore the tool diameter measurements.

                                      Cheers
                                      E

                                      1 Reply Last reply Reply Quote 0
                                      • Hagridundefined
                                        Hagrid @rilot
                                        last edited by

                                        @rilot Thank you 🙂

                                        1 Reply Last reply Reply Quote 0
                                        • chimaeraghundefined
                                          chimaeragh
                                          last edited by

                                          Hi. I just saw that this project has been updated to DWC 3.3 rc1. Glad to know it hasn't been abandoned. I'll be getting a Neje laser module to attach to my CNC soon and will be coming back to RRF3

                                          Duet 2 Wifi, Ooznest Workbee CNC 1510

                                          Sindariusundefined 1 Reply Last reply Reply Quote 2
                                          • Sindariusundefined
                                            Sindarius @chimaeragh
                                            last edited by

                                            @chimaeragh I promise it is not abandoned 🙂 I have a few other tasks which has taken up a bit of time. I plan on getting an XYZ probe plugin put in place when I am able to put some time into it. I have an OpenBuilds CNC with an XYZ touch probe that I want to get up and running as well.

                                            cjmundefined bitminterundefined 2 Replies Last reply Reply Quote 2
                                            • First post
                                              Last post
                                            Unless otherwise noted, all forum content is licensed under CC-BY-SA