Cannot Connect to Duet 3 Web Control

Frank 0 · 15 Jul 2021, 18:41

@phaedrux Could you point me back to where you listed the folders I need? I don't see it, I must be blind. I download the 3.3 firmware and then just put it in the www folder?

Phaedrux · 15 Jul 2021, 18:45

@phaedrux said in Cannot Connect to Duet 3 Web Control:

@frank-0 said in Cannot Connect to Duet 3 Web Control:

@kb58 After using Bossa to reset my firmware, I cannot find the config.g file. The sys folder changed to this

I have never seen anything like that before.

I suggest you get a clean new SD card, format it as FAT32, and then start fresh from there.

Create the following folders

sys
macros
www
gcodes
menu
filaments

Create a fresh config file set from here: https://configtool.reprapfirmware.org/Start

Fill out the info to the best of your knowledge. We just want a starting point.

What firmware bin file version did you use to flash with Bossa? 3.3?

https://github.com/Duet3D/RepRapFirmware/releases/download/3.3/DuetWebControl-SD.zip

Download that zip file and extract it into the /www/ folder.

That should get your SD card back to a working state.

Here it is.

Frank 0 · 15 Jul 2021, 18:48

@phaedrux What should be in the macros/gcodes/menu/filaments folder? I can make the folders, but Im not sure what to put in them.

Phaedrux · 15 Jul 2021, 19:48

@frank-0 Nothing. They will be empty.

The gcodes folder is where your uploaded print files will go. menu is a folder for menu files when using a rotary encoder display. And filaments is used to store filament profiles if you set them up. They just need to exist otherwise you'll get a little warning that they are mising.

Oh, and the firmware folder is where firmware files will go in future

Frank 0 · 15 Jul 2021, 19:50

@phaedrux I got this set up and have this currently:

This is my config.g file:

and I extracted 3.3 firmware into www folder. YAT still doesn't really work. M552 S1 P192.168.2.2 just responds with ok, not network running.

Frank 0 · 15 Jul 2021, 19:52

@frank-0 There is also no lights lit up at bottom of the ethernet port

Phaedrux · 15 Jul 2021, 19:54

@frank-0 said in Cannot Connect to Duet 3 Web Control:

and I extracted 3.3 firmware into www folder.

Don't do that.

@frank-0 said in Cannot Connect to Duet 3 Web Control:

M552 S1 P192.168.2.2 just responds with ok,

If you send M552 what does it say?

@frank-0 said in Cannot Connect to Duet 3 Web Control:

I got this set up and have this currently:

Don't forget to add a folder called firmware.

Frank 0 · 15 Jul 2021, 19:55

@phaedrux www folder :

YAT literally just says "ok", like in the images above from a while ago.

Should I just make an empty folder called "firmware"?

Phaedrux · 15 Jul 2021, 19:56

Are you able to ping 192.168.2.2?

What IP is your computer using?

Have you tried a different cable?

Do the lights on the ethernet port light up if you connect to your router instead? even briefly?

Frank 0 · 15 Jul 2021, 19:57

@phaedrux Timed out, is unreachable. Can't ping it

Phaedrux · 15 Jul 2021, 20:00

What IP is your computer using?

Have you tried a different cable?

Do the lights on the ethernet port light up if you connect to your router instead? even briefly?

Frank 0 · 15 Jul 2021, 20:00

@phaedrux Computer is using an assigned IP address I changed in the control panel. It is 192.168.2.1. I tried different cable and no the lights don't light up at all.

Phaedrux · 15 Jul 2021, 20:02

@frank-0 said in Cannot Connect to Duet 3 Web Control:

I tried different cable and no the lights don't light up at all.

Not with the router either?

Frank 0 · 15 Jul 2021, 20:03

@phaedrux Yeah doesn't light up with either computer or router

Phaedrux · 15 Jul 2021, 20:06

Alright, I think we've solved the firmware problem since it's able to speak with YAT now and it is taking and executing commands.

I think we have the SD card issue solved.

Can you post your current config.g from the /sys/ folder please?

Frank 0 · 15 Jul 2021, 20:07

@phaedrux

Phaedrux · 15 Jul 2021, 20:09

Copy and paste the text please.

Frank 0 · 15 Jul 2021, 20:10

@phaedrux ; Configuration file for Duet 3 (firmware version 3)
; executed by the firmware on start-up
;
; generated by RepRapFirmware Configuration Tool v3.2.3 on Thu Jul 15 2021 14:31:46 GMT-0700 (Pacific Daylight Time)

; General preferences
G90 ; send absolute coordinates...
M83 ; ...but relative extruder moves
M550 P"My Printer" ; set printer name

; Network
M552 P192.168.2.2 S1 ; enable network and set IP address
M553 P255.255.255.0 ; set netmask
M554 P192.168.1.254 ; set gateway
M586 P0 S1 ; enable HTTP
M586 P1 S0 ; disable FTP
M586 P2 S0 ; disable Telnet

; Drives
M569 P0.0 S1 ; physical drive 0.0 goes forwards
M569 P0.1 S1 ; physical drive 0.1 goes forwards
M569 P0.2 S1 ; physical drive 0.2 goes forwards
M569 P0.3 S1 ; physical drive 0.3 goes forwards
M584 X0.0 Y0.1 Z0.2 E0.3 ; set drive mapping
M350 X16 Y16 Z16 E16 I1 ; configure microstepping with interpolation
M92 X80.00 Y80.00 Z400.00 E420.00 ; set steps per mm
M566 X900.00 Y900.00 Z60.00 E120.00 ; set maximum instantaneous speed changes (mm/min)
M203 X6000.00 Y6000.00 Z180.00 E1200.00 ; set maximum speeds (mm/min)
M201 X500.00 Y500.00 Z20.00 E250.00 ; set accelerations (mm/s^2)
M906 X800 Y800 Z800 E800 I30 ; set motor currents (mA) and motor idle factor in per cent
M84 S30 ; Set idle timeout

; Axis Limits
M208 X0 Y0 Z0 S1 ; set axis minima
M208 X230 Y210 Z200 S0 ; set axis maxima

; Endstops
; WARNING: No endstops configured

; Z-Probe
M558 P0 H5 F120 T6000 ; disable Z probe but set dive height, probe speed and travel speed
M557 X15:215 Y15:195 S20 ; define mesh grid

; Heaters
M308 S0 P"temp1" Y"thermistor" T100000 B4138 ; configure sensor 0 as thermistor on pin temp1
M950 H0 C"out0" T0 ; create bed heater output on out0 and map it to sensor 0
M307 H0 B1 S1.00 ; enable bang-bang mode for the bed heater and set PWM limit
M140 H0 ; map heated bed to heater 0
M143 H0 S120 ; set temperature limit for heater 0 to 120C
M308 S1 P"temp0" Y"thermistor" T100000 B4138 ; configure sensor 1 as thermistor on pin temp0
M950 H1 C"out2" T1 ; create nozzle heater output on out2 and map it to sensor 1
M307 H1 B0 S1.00 ; disable bang-bang mode for heater and set PWM limit
M143 H1 S280 ; set temperature limit for heater 1 to 280C

; Fans
M950 F0 C"out4" Q500 ; create fan 0 on pin out4 and set its frequency
M106 P0 S0 H-1 ; set fan 0 value. Thermostatic control is turned off
M950 F1 C"!out6" Q500 ; create fan 1 on pin !out6 and set its frequency
M106 P1 S1 H1 T45 ; set fan 1 value. Thermostatic control is turned on

; Tools
M563 P0 D0 H1 F0 ; define tool 0
G10 P0 X0 Y0 Z0 ; set tool 0 axis offsets
G10 P0 R0 S0 ; set initial tool 0 active and standby temperatures to 0C

; Custom settings are not defined

Phaedrux · 15 Jul 2021, 20:16

@frank-0 said in Cannot Connect to Duet 3 Web Control:

M554 P192.168.1.254 ; set gateway

Does this match the gateway you have set on your PC?

On your PC open a command prompt and send ipconfig and see what it says.

Frank 0 · 15 Jul 2021, 20:19

@phaedrux I currently use one ethernet running to the router so my computer has wifi. Then I use another ethernet connected to the board and the desktop (via USB adapter). Only one of the ethernet cords shows information about IP/gateway. And this one does not match