Mini 5+ Eth./Win10/can't connect to DWC

Yurk_12

Hi,

I'm failing at Step 11 of the Getting Connected doc.

Config

Duet 3 Mini 5+ Ethernet freshly received, first time trying.
Windows 10
Board connected and powered by USB computer port
Ethernet cable connected to computer directly: tried both normal and crossover cables
Firmware 3.2.2 (I could not update the firmware in step #7 because it needs access to DWC)
The green and yellow network LEDs on the board are ON. The green one sometimes blinks.

Problem

In YAT I have:

M552 S0
Network stopped
ok
M552 S1 P120.20.20.20
ok
Ethernet running, IP address = 120.20.20.20
M552
Ethernet is enabled, configured IP address: 120.20.20.20, actual IP address: 120.20.20.20
ok

Putting the IP in Chrome does not work. Going to duettest.local does not work either.

Below is the diagnostics M122. Am I doing something wrong?
Thanks for any help

M122
=== Diagnostics ===
RepRapFirmware for Duet 3 Mini 5+ version 3.2.2 running on Duet 3 Mini5plus Ethernet (standalone mode)
Board ID: 5DNBA-B296U-D65J0-40KM6-2503Z-HSDTT
Used output buffers: 1 of 40 (15 max)
=== RTOS ===
Static ram: 98732
Dynamic ram: 101112 of which 404 recycled
Never used RAM 44968, free system stack 124 words
Tasks: NETWORK(ready,454) ETHERNET(blocked,652) HEAT(blocked,362) CanReceiv(blocked,947) CanSender(blocked,372) CanClock(blocked,362) TMC(blocked,123) MAIN(running,400) IDLE(ready,20) AIN(blocked,260)
Owned mutexes: USB(MAIN)
=== Platform ===
Last reset 00:33:15 ago, cause: power up
Last software reset time unknown, reason: HardFault bfarValid precise, GCodes spinning, available RAM 44968, slot 0
Software reset code 0x0063 HFSR 0x40000000 CFSR 0x00008200 ICSR 0x00000803 BFAR 0x00000040 SP 0x2000a7e0 Task MAIN Freestk 779 ok
Stack: 00000000 00000571 0000056d 00000000 ffffffff 000664e9 000781ca 61010000 00000000 ffffffff 2001c8dc 20009b54 2001c6d8 2000a850 000914f0 200095b4 2000a8ec 0007dca3 00000001 2000a850 20000008 0007b369 0008bd6c 0006d049 20028928 20000008 20000008
Error status: 0x00
Aux0 errors 0,0,0
Aux1 errors 0,0,0
Supply voltage: min 0.9, current 0.9, max 0.9, under voltage events: 0, over voltage events: 0, power good: no
Driver 0: position 0, ok, SG min/max not available, read errors 0, write errors 0, ifcnt 0, reads 0, writes 0, timeouts 0, DMA errors 0
Driver 1: position 0, ok, SG min/max not available, read errors 0, write errors 0, ifcnt 0, reads 0, writes 0, timeouts 0, DMA errors 0
Driver 2: position 0, ok, SG min/max not available, read errors 0, write errors 0, ifcnt 0, reads 0, writes 0, timeouts 0, DMA errors 0
Driver 3: position 0, ok, SG min/max not available, read errors 0, write errors 0, ifcnt 0, reads 0, writes 0, timeouts 0, DMA errors 0
Driver 4: position 0, ok, SG min/max not available, read errors 0, write errors 0, ifcnt 0, reads 0, writes 0, timeouts 0, DMA errors 0
Driver 5: position 0, ok, SG min/max not available, read errors 0, write errors 0, ifcnt 0, reads 0, writes 0, timeouts 0, DMA errors 0
Driver 6: position 0, ok, SG min/max not available, read errors 0, write errors 0, ifcnt 0, reads 0, writes 0, timeouts 0, DMA errors 0
Date/time: 1970-01-01 00:00:00
Cache data hit count 3907942329
Slowest loop: 4.47ms; fastest: 0.12ms
=== Storage ===
Free file entries: 10
SD card 0 detected, interface speed: 22.5MBytes/sec
SD card longest read time 3.2ms, write time 0.0ms, max retries 0
=== Move ===
DMs created 83, maxWait 0ms, bed compensation in use: none, comp offset 0.000
=== MainDDARing ===
Scheduled moves 0, completed moves 0, hiccups 0, stepErrors 0, LaErrors 0, Underruns [0, 0, 0], CDDA state -1
=== AuxDDARing ===
Scheduled moves 0, completed moves 0, hiccups 0, stepErrors 0, LaErrors 0, Underruns [0, 0, 0], CDDA state -1
=== Heat ===
Bed heaters = -1 -1, chamberHeaters = -1 -1
=== GCodes ===
Segments left: 0
Movement lock held by null
HTTP is idle in state(s) 0
Telnet is idle in state(s) 0
File is idle in state(s) 0
USB is ready with "M122" in state(s) 0
Aux is idle in state(s) 0
Trigger is idle in state(s) 0
Queue is idle in state(s) 0
LCD is idle in state(s) 0
SBC is idle in state(s) 0
Daemon is idle in state(s) 0
Aux2 is idle in state(s) 0
Autopause is idle in state(s) 0
Code queue is empty.
=== Network ===
Slowest loop: 0.45ms; fastest: 0.01ms
Responder states: HTTP(0) HTTP(0) HTTP(0) HTTP(0) FTP(0) Telnet(0), 0 sessions
HTTP sessions: 0 of 8
- Ethernet -
State: active
Error counts: 0 0 0 0 0
Socket states: 2 2 2 2 2 0 0 0
=== CAN ===
Messages queued 8774, send timeouts 8774, received 0, lost 0, longest wait 0ms for reply type 0, free buffers 16
ok

Phaedrux

@yurk_12 said in Mini 5+ Eth./Win10/can't connect to DWC:

Ethernet cable connected to computer directly

And what IP address does your computer have? Is it in the same subnet as 120.20.20.x?

Updating the firmware on the mini5 is a bit different over USB.
https://duet3d.dozuki.com/Wiki/Installing_and_Updating_Firmware#Section_Duet_3_Mini_5_WiFi_Ethernet

Yurk_12

@phaedrux

And what IP address does your computer have? Is it in the same subnet as 120.20.20.x?

Oh, it was not in the same subnet indeed.

Autoconfiguration IPv4 Address. . : 169.254.163.65

I changed the IP of the board as follows:

M552 S0
Network stopped
ok
M552 S1 P169.254.163.66
ok
Ethernet running, IP address = 169.254.163.66
M552
Ethernet is enabled, configured IP address: 169.254.163.66, actual IP address: 169.254.163.66
ok

and now it works:

Updating the firmware on the mini5 is a bit different over USB.
https://duet3d.dozuki.com/Wiki/Installing_and_Updating_Firmware#Section_Duet_3_Mini_5_WiFi_Ethernet

Oh great, thanks, I had missed it.

Thanks a lot for your help