• Tags
  • Documentation
  • Order
  • Register
  • Login
Duet3D Logo Duet3D
  • Tags
  • Documentation
  • Order
  • Register
  • Login

warning leds

Scheduled Pinned Locked Moved
Duet Hardware and wiring
5
15
418
Loading More Posts
  • Oldest to Newest
  • Newest to Oldest
  • Most Votes
Reply
  • Reply as topic
Log in to reply
This topic has been deleted. Only users with topic management privileges can see it.
  • ?
    A Former User @A Former User
    last edited by 25 Aug 2021, 15:12

    @ooly
    Jay, thanks. where is the diagram? could not find it

    undefined 1 Reply Last reply 25 Aug 2021, 15:24 Reply Quote 0
    • undefined
      cosmowave @A Former User
      last edited by 25 Aug 2021, 15:24

      @ooly https://duet3d.dozuki.com/Wiki/Duet_3_Expansion_3HC_Wiring_Diagram#Section_LED_indications

      Mankati FSXT+, DeltaTowerV2, E3D MS/TC

      1 Reply Last reply Reply Quote 1
      • undefined
        kb58
        last edited by kb58 25 Aug 2021, 15:50

        @ooly said in warning leds:

        flashing infrequently

        Well... what do you mean by "flashing infrequently"? It's a bit of a double meaning depending on interpretation. It's normally flashing at a periodic 1Hz rate.

        Scratch-built 350mmx350mm coreXY, linear rails, ballscrews, 3 Z axis, Duet3 6HC, v3.3, Tool Board v1.1, BondTech LGX + Mosquito hot end

        1 Reply Last reply Reply Quote 0
        • ?
          A Former User
          last edited by 26 Aug 2021, 06:16

          @kb58
          about 20 s off and 4-6 s on. wide variations.

          ? 1 Reply Last reply 26 Aug 2021, 06:26 Reply Quote 0
          • ?
            A Former User @A Former User
            last edited by 26 Aug 2021, 06:26

            @ooly
            cosmowave, the site you have suggested tie the flashing to expansion board. I don't have one. however, I uae a paneldue and it had stopped working before I opened the controller box and observed the flashing. any possible connection? thanks

            undefined 1 Reply Last reply 26 Aug 2021, 06:28 Reply Quote 0
            • undefined
              cosmowave @A Former User
              last edited by 26 Aug 2021, 06:28

              @ooly You can find all infos in the dozuki...
              https://duet3d.dozuki.com/Wiki/Duet_3_Mainboard_6HC_Wiring_Diagram

              Mankati FSXT+, DeltaTowerV2, E3D MS/TC

              ? 1 Reply Last reply 26 Aug 2021, 08:20 Reply Quote 0
              • ?
                A Former User @cosmowave
                last edited by 26 Aug 2021, 08:20

                @cosmowave
                thanks

                1 Reply Last reply Reply Quote 0
                • undefined
                  dc42 administrators @A Former User
                  last edited by 26 Aug 2021, 12:45

                  @ooly said in warning leds:

                  I have a red led flashing infrequently while the system works, presumably in a normal way. location: just left of the fuse, next to what seems like a voltage regulator (?).
                  what is it?

                  Which Duet?

                  Duet WiFi hardware designer and firmware engineer
                  Please do not ask me for Duet support via PM or email, use the forum
                  http://www.escher3d.com, https://miscsolutions.wordpress.com

                  ? 1 Reply Last reply 28 Aug 2021, 06:47 Reply Quote 0
                  • ?
                    A Former User @dc42
                    last edited by 28 Aug 2021, 06:47

                    @dc42
                    duet 2 wifi

                    ? 1 Reply Last reply 28 Aug 2021, 06:52 Reply Quote 0
                    • ?
                      A Former User @A Former User
                      last edited by 28 Aug 2021, 06:52

                      @ooly
                      also, since the paneldue does not work, I don't know which wifi channel to call for and therefore cannot connect to the controller.
                      how do I find the channel without paneldue?

                      ? 1 Reply Last reply 28 Aug 2021, 08:05 Reply Quote 0
                      • ?
                        A Former User @A Former User
                        last edited by 28 Aug 2021, 08:05

                        @ooly
                        I found the channel thru YAT. is there a simpler way? thanks

                        ? 1 Reply Last reply 28 Aug 2021, 08:50 Reply Quote 0
                        • ?
                          A Former User @A Former User
                          last edited by 28 Aug 2021, 08:50

                          @ooly
                          in the meantime I found the explanation concerning mDNS connecting by name. tried it and it did not work

                          1 Reply Last reply Reply Quote 0
                          • undefined
                            dc42 administrators
                            last edited by 28 Aug 2021, 09:19

                            On the Duet 2 the DIAG LED is driven from the ZProbe MOD pin. When using some types of Z probe, that LED will light during a probing move.

                            also, since the paneldue does not work, I don't know which wifi channel to call for and therefore cannot connect to the controller.

                            There are various things that cause PanelDue not to work:

                            • Missing M575 P1 B57600 command in config.g
                            • Mismatched baud rates
                            • Cable bad or not connected correctly

                            Please start a new thread if you still have a problem getting PanelDue to work.

                            Duet WiFi hardware designer and firmware engineer
                            Please do not ask me for Duet support via PM or email, use the forum
                            http://www.escher3d.com, https://miscsolutions.wordpress.com

                            1 Reply Last reply Reply Quote 0
                            12 out of 15
                            • First post
                              12/15
                              Last post
                            Unless otherwise noted, all forum content is licensed under CC-BY-SA