Problem with G30
-
Hello,
yesterday i have build my Printer with the Due Wifi board with the Firmware 1.18 and all functions were good!
Today i have the Firmware upgraded to 1.19. +3 and now the Printer will Crash with the G30 command as shown in this Video
https://photos.google.com/share/AF1QipMx7FYw6zy2upiM2hqK8RYynvf0VWZQmeXnv8H3ma7-Iyo1H0cajoW8roNWTnE-lQ?key=T0I0R2RBQlJ2OTV0VC1MeDgzNjRIOER0cFNBVE9Ri have "played" with this settings
G31 P600 X0 Y0 Z2.5 ; Set Z probe trigger value, offset and trigger height
M557 X15:395 Y15:395 S20 ; Define mesh gridi have testet the x and y values with positive and negative values but noting changes
can someone tell me were i make a mistake ?regards
Andy
here is my Config file :
; Configuration file for Duet WiFi (firmware version 1.17)
; executed by the firmware on start-up
;
; generated by RepRapFirmware Configuration Tool on Mon Aug 28 2017 12:04:38 GMT+0200; General preferences
M111 S0 ; Debugging off
G21 ; Work in millimetres
G90 ; Send absolute coordinates…
M83 ; ...but relative extruder moves
M555 P2 ; Set firmware compatibility to look like MarlinM667 S1 ; Select CoreXY mode
M208 X-10 Y-10 Z0 S1 ; Set axis minima
M208 X420 Y420 Z450 S0 ; Set axis maxima; Endstops
M574 Z0 S0 ; Define active low and unused microswitches
M574 X1 Y1 S1 ; Define active high microswitches
M558 P1 X0 Y0 Z1 H5 F120 T6000 ; Set Z probe type to unmodulated, the axes for which it is used and the probe + travel speeds
G31 P600 X0 Y0 Z2.5 ; Set Z probe trigger value, offset and trigger height
M557 X15:395 Y15:395 S20 ; Define mesh grid; Drives
M569 P0 S1 ; Drive 0 goes forwards
M569 P1 S1 ; Drive 1 goes forwards
M569 P2 S1 ; Drive 2 goes forwards
M569 P3 S1 ; Drive 3 goes forwards
M350 X16 Y16 Z16 E16 I0 ; Configure microstepping without interpolation
M92 X80.85 Y80 Z1065.73 E100 ; Set steps per mm
M566 X900 Y900 Z12 E120 ; Set maximum instantaneous speed changes (mm/min)
M203 X24000 Y24000 Z480 E1500 ; Set maximum speeds (mm/min)
M201 X1500 Y1500 Z100 E10000 ; Set accelerations (mm/s^2)
M906 X1600 Y1600 Z2000 E1600 I30 ; Set motor currents (mA) and motor idle factor in per cent
M84 S30 ; Set idle timeout; Heaters
M143 S260 ; Set maximum heater temperature to 260C
M305 P0 T100000 B4138 C0 R4700 ; Set thermistor + ADC parameters for heater 0
M305 P1 T100000 B4138 C0 R4700 ; Set thermistor + ADC parameters for heater 1; Tools
M563 P0 D0 H1 ; Define tool 0
G10 P0 X0 Y0 Z0 ; Set tool 0 axis offsets
G10 P0 R0 S0 ; Set initial tool 0 active and standby temperatures to 0C; Network
M550 Phypercube ; Set machine name
M552 S1 ; Enable network
M587 Skleinersonnenschein.eu P"*********************" ; Configure access point. You can delete this line once connected
M586 P0 S1 ; Enable HTTP
M586 P1 S0 ; Disable FTP
M586 P2 S0 ; Disable Telnet; Fans
M106 P0 S0 I0 F500 H-1 ; Set fan 0 value, PWM signal inversion and frequency. Thermostatic control is turned off
M106 P1 S1 I0 F500 H1 T35 ; Set fan 1 value, PWM signal inversion and frequency. Thermostatic control is turned on
M106 P2 S1 I0 F500 H1 T45 ; Set fan 2 value, PWM signal inversion and frequency. Thermostatic control is turned on; Custom settings are not configured
-
There are a couple of folders you have to remove after upgrading. Did you read all of the release notes and trouble shooting guide?
-
It's most likely trying to run deployprobe macros which have to be deleted.
-
thanks deployprobe was the problem
-
Also delete retractprobe.g if it is there.
