Mini 5 mini SD inop after months of use
-
Ive had a Mini 5 in commission for about 6 months and its been working just fine. 2 months ago, out of the blue, it would not load the files from the SD card. I was slammed for time to diag it so I put a new board in that printer to keep the farm turning out max capacity. I tried a new SD, used Bossa to flash new FW, and I can connect and send/receive with YAT terminal. Purchased through Spool3D, they advised the forum before they can issue warranty.
Thanks!
-
Can you gather the result of M122?
Can you send M22 to unmount, M21 to mount the card?
-
@phaedrux Ill give it a go this weekend! I believe tried to mount the card but cant recall for sure. Ill let you know!
-
@phaedrux
M122
=== Diagnostics ===
RepRapFirmware for Duet 3 Mini 5+ version 3.2.2 running on Duet 3 Mini5plus WiFi (standalone mode)
Board ID: 1H88H-V196U-D65J0-40KMU-0Z03Z-RQD4F
Used output buffers: 1 of 40 (1 max)
=== RTOS ===
Static ram: 98732
Dynamic ram: 106368 of which 552 recycled
Never used RAM 39564, free system stack 136 words
Tasks: NETWORK(ready,518) HEAT(blocked,362) CanReceiv(blocked,947) CanSender(blocked,372) CanClock(blocked,363) TMC(blocked,123) MAIN(running,634) IDLE(ready,20) AIN(blocked,269)
Owned mutexes: USB(MAIN)
=== Platform ===
Last reset 00:03:21 ago, cause: power up
Last software reset at 2021-09-01 21:06, reason: User, GCodes spinning, available RAM 33744, slot 0
Software reset code 0x0003 HFSR 0x00000000 CFSR 0x00000000 ICSR 0x00000000 BFAR 0xe000ed38 SP 0x00000000 Task MAIN Freestk 0 n/a
Error status: 0x00
Aux0 errors 0,0,0
Aux1 errors 0,0,0
Supply voltage: min 0.0, current 0.9, max 0.9, under voltage events: 0, over voltage events: 0, power good: no
Driver 0: position 0, ok, SG min/max not available, read errors 0, write errors 0, ifcnt 0, reads 0, writes 0, timeouts 0, DMA errors 0
Driver 1: position 0, ok, SG min/max not available, read errors 0, write errors 0, ifcnt 0, reads 0, writes 0, timeouts 0, DMA errors 0
Driver 2: position 0, ok, SG min/max not available, read errors 0, write errors 0, ifcnt 0, reads 0, writes 0, timeouts 0, DMA errors 0
Driver 3: position 0, ok, SG min/max not available, read errors 0, write errors 0, ifcnt 0, reads 0, writes 0, timeouts 0, DMA errors 0
Driver 4: position 0, ok, SG min/max not available, read errors 0, write errors 0, ifcnt 0, reads 0, writes 0, timeouts 0, DMA errors 0
Driver 5: position 0, ok, SG min/max not available, read errors 0, write errors 0, ifcnt 0, reads 0, writes 0, timeouts 0, DMA errors 0
Driver 6: position 0, ok, SG min/max not available, read errors 0, write errors 0, ifcnt 0, reads 0, writes 0, timeouts 0, DMA errors 0
Date/time: 1970-01-01 00:00:00
Cache data hit count 475358797
Slowest loop: 0.19ms; fastest: 0.12ms
=== Storage ===
Free file entries: 10
SD card 0 detected, interface speed: 0.2MBytes/sec
SD card longest read time 0.0ms, write time 0.0ms, max retries 0
=== Move ===
DMs created 83, maxWait 0ms, bed compensation in use: none, comp offset 0.000
=== MainDDARing ===
Scheduled moves 0, completed moves 0, hiccups 0, stepErrors 0, LaErrors 0, Underruns [0, 0, 0], CDDA state -1
=== AuxDDARing ===
Scheduled moves 0, completed moves 0, hiccups 0, stepErrors 0, LaErrors 0, Underruns [0, 0, 0], CDDA state -1
=== Heat ===
Bed heaters = -1 -1, chamberHeaters = -1 -1
=== GCodes ===
Segments left: 0
Movement lock held by null
HTTP is idle in state(s) 0
Telnet is idle in state(s) 0
File is idle in state(s) 0
USB is ready with "M122" in state(s) 0
Aux is idle in state(s) 0
Trigger is idle in state(s) 0
Queue is idle in state(s) 0
LCD is idle in state(s) 0
SBC is idle in state(s) 0
Daemon is idle in state(s) 0
Aux2 is idle in state(s) 0
Autopause is idle in state(s) 0
Code queue is empty.
=== Network ===
Slowest loop: 0.19ms; fastest: 0.00ms
Responder states: HTTP(0) HTTP(0) HTTP(0) HTTP(0) FTP(0) Telnet(0), 0 sessions
HTTP sessions: 0 of 8- WiFi -
Network state is disabled
WiFi module is disabled
Failed messages: pending 2779096485, notready 2779096485, noresp 2779096485
Socket states: 0 0 0 0 0 0 0 0
=== CAN ===
Messages queued 1009, send timeouts 1008, received 0, lost 0, longest wait 0ms for reply type 0, free buffers 16
ok
M22
SD card 0 may now be removed
ok
M21Error: M21: Cannot initialise SD card 0: Card is unusable
ok - WiFi -
-
Thanks for that. I think your SD card socket or interface has failed.
@leckietech said in Mini 5 mini SD inop after months of use:
SD card 0 detected, interface speed: 0.2MBytes/sec
Error: M21: Cannot initialise SD card 0: Card is unusable
okPlease send an email to warranty@duet3d.com and CC your reseller. Include a link to this forum thread and the details of your original purchase. You'll receive a reply with a form to fill out.
-
@phaedrux Thank you!
