G28 Z "Error: probe 0 not found"
-
The Z axis home'd properly one week ago, but not anymore.
The BL touch itself is good, and i cannot remember remotely touching it in the config.
I don't know what to do, please help.; Configuration file for Duet WiFi (firmware version 3.3)
; executed by the firmware on start-up
;
; generated by RepRapFirmware Configuration Tool v3.3.10 on Sat Jan 08 2022 17:50:57 GMT+0100 (Midden-Europese standaardtijd); General preferences
M575 P1 S1 B57600 ; enable support for PanelDue
G90 ; send absolute coordinates...
M83 ; ...but relative extruder moves
M550 P"Modix Big-60" ; set printer name; Network
M552 S1 ; enable network
M586 P0 S1 ; enable HTTP
M586 P1 S0 ; disable FTP
M586 P2 S0 ; disable Telnet; Drives
M569 P0 S0 ; physical drive 0 goes forwards. X-Axis.
M569 P1 S0 ; physical drive 1 goes forwards. Y-Axis.
M569 P2 S0 ; physical drive 2 goes forwards. Z-Axis.
M569 P3 S1 ; physical drive 3 goes forwards. E0-Extruder.
M584 X0 Y1 Z2 E3 ; set drive mapping
M350 X16 Y16 Z16 E16 I1 ; configure microstepping with interpolation
;M92 X80.00 Y160.00 Z400.00 E420.00 ; set steps per mm
M92 X100 Y195 Z2000 E418.5:418.5
M566 X900.00 Y900.00 Z60.00 E120.00 ; set maximum instantaneous speed changes (mm/min)
M203 X6000.00 Y6000.00 Z2000.00 E1200.00 ; set maximum speeds (mm/min)
M201 X500.00 Y500.00 Z100.00 E250.00 ; set accelerations (mm/s^2)
M906 X1800 Y1800 Z2400 E1000 I40 ; set motor currents (mA) and motor idle factor in per cent
M84 S30 ; Set idle timeout; Axis Limits
M208 X0 Y0 Z0 S1 ; set axis minima
M208 X610 Y610 Z610 S0 ; set axis maxima; Endstops
M574 X1 S1 P"!^xstop" ; configure switch-type (e.g. microswitch) endstop for low end on X via pin xstop
M574 Y1 S1 P"!^ystop" ; configure switch-type (e.g. microswitch) endstop for low end on Y via pin ystop
M574 Z1 S2 ; Define Z to use BLTouch probe; Z-Probe BLTouch on Duet WiFi
M950 S0 C"exp.heater7" ; create servo pin 0 for BLTouch
M558 P7 C"^zprobe.in" H15 F120 T3000 A5 ; set Z probe type to bltouch and the dive height + speeds
M280 P7 S10 ; send control signal to BLTouch through servo/gpio 0"
G31 X20 Y0 Z3.3 P25; Heaters
M308 S0 P"bedtemp" Y"thermistor" T100000 B4138 ; configure sensor 0 as thermistor on pin bedtemp
M950 H0 C"bedheat" T0 ; create bed heater output on bedheat and map it to sensor 0
M307 H0 B1 S1.00 ; enable bang-bang mode for the bed heater and set PWM limit
M140 H0 ; map heated bed to heater 0
M143 H0 S120 ; set temperature limit for heater 0 to 120C
M308 S1 P"e0temp" Y"thermistor" T100000 B4138 ; configure sensor 1 as thermistor on pin e0temp
M950 H1 C"e0heat" T1 ; create nozzle heater output on e0heat and map it to sensor 1
M307 H1 B0 S1.00 ; disable bang-bang mode for heater and set PWM limit
M143 H1 S280 ; set temperature limit for heater 1 to 280C; Fans
M950 F0 C"fan0" Q500 ; create fan 0 on pin fan0 and set its frequency
M106 P0 S0 H-1 ; set fan 0 value. Thermostatic control is turned off
M950 F1 C"fan1" Q500 ; create fan 1 on pin fan1 and set its frequency
M106 P1 S1 H1 T45 ; set fan 1 value. Thermostatic control is turned on; Tools
M563 P0 D0 H1 F0 ; define tool 0
G10 P0 X0 Y0 Z0 ; set tool 0 axis offsets
G10 P0 R0 S0 ; set initial tool 0 active and standby temperatures to 0C; Custom settings are not defined
; Miscellaneous
M501 ; load saved parameters from non-volatile memory
M911 S10 R11 P"M913 X0 Y0 G91 M83 G1 Z3 E-5 F1000" ; set voltage thresholds and actions to run on power loss -
Z probe types 4, 6 and 7 (used in RRF 2.x) are no longer supported. Instead, use type 5 (filtered digital) or 8 (unfiltered digital) and use the C parameter to specify the input.see here https://docs.duet3d.com/en/User_manual/Reference/Gcodes#m558-set-z-probe-type
use P9 -
@jay_s_uk
how do i do that -
@3dorbit change the P value in M558
-
@jay_s_uk thanks a lot
