Enable Retract/Extrude in Extrusion Control

[crowem]

I no longer seem to be able to extrude test some things from the web interface. I know that this was an issues before when i did not have a loaded filament in the interface but now I don't seen an option to load a filament in to enable these options.

[Phaedrux]

What firmware version and DWC version are you using?
Can you share your config.g please?

[crowem]

@Phaedrux
Duet Web Control 3.4.1

; Configuration file for Duet 3 MB 6HC (firmware version 3.3)
; executed by the firmware on start-up
;
; generated by RepRapFirmware Configuration Tool v3.3.15 on Fri Dec 16 2022 11:47:29 GMT-0600 (Central Standard Time)
 
; General preferences
G90                                               ; send absolute coordinates...
M83                                               ; ...but relative extruder moves
M550 P"Duet 3"                                    ; set printer name
 
; Drives
M569 P0.2 S0                                      ; physical drive 0.2 goes backwards
M569 P0.1 S0                                      ; physical drive 0.1 goes backwards
M569 P0.0 S0                                      ; physical drive 0.0 goes backwards
M569 P0.3 S0                                      ; physical drive 0.3 goes backwards
M569 P0.4 S1                                      ; physical drive 0.4 goes forwards
M584 X0.2 Y0.1 Z0.0 E0.3:0.4                      ; set drive mapping
M350 X16 Y16 Z16 E16:16 I1                        ; configure microstepping with interpolation
M92 X100.00 Y100.00 Z400.00 E95.00:95.00          ; set steps per mm
M566 X1200.00 Y1200.00 Z60.00 E1500.00:1500.00    ; set maximum instantaneous speed changes (mm/min)
M203 X12000.00 Y12000.00 Z180.00 E6000.00:6000.00 ; set maximum speeds (mm/min)
M201 X4000.00 Y4000.00 Z20.00 E1000.00:1000.00    ; set accelerations (mm/s^2)
M906 X900 Y900 Z900 E900:900 I30                  ; set motor currents (mA) and motor idle factor in per cent
M84 S30                                           ; Set idle timeout
 
; Axis Limits
M208 X-127 Y-92 Z0 S1                             ; set axis minima
M208 X140 Y92 Z160 S0                             ; set axis maxima
 
; Endstops
M574 X2 S1 P"!io2.in"                             ; configure switch-type (e.g. microswitch) endstop for high end on X via pin !io2.in
M574 Y2 S1 P"!io0.in"                             ; configure switch-type (e.g. microswitch) endstop for high end on Y via pin !io0.in
M574 Z1 S2                                        ; configure Z-probe endstop for low end on Z
 
; Z-Probe
M558 P1 C"io3.in" H5 F120 T6000                   ; set Z probe type to unmodulated and the dive height + speeds
G31 P990 X-10 Y5 Z1.1                             ; set Z probe trigger value, offset and trigger height
M557 X-95:105 Y-86:90 S10                         ; define mesh grid
 
; Heaters
M308 S0 P"temp0" Y"thermistor" T100000 B4138      ; configure sensor 0 as thermistor on pin temp0
M950 H0 C"out0" T0                                ; create bed heater output on out0 and map it to sensor 0
M307 H0 B0 S1.00                                  ; disable bang-bang mode for the bed heater and set PWM limit
M140 H0                                           ; map heated bed to heater 0
M143 H0 S280                                      ; set temperature limit for heater 0 to 280C
M308 S1 P"temp1" Y"thermistor" T100000 B4138      ; configure sensor 1 as thermistor on pin temp1
M950 H1 C"out1" T1                                ; create nozzle heater output on out1 and map it to sensor 1
M307 H1 B0 S1.00                                  ; disable bang-bang mode for heater  and set PWM limit
M143 H1 S280                                      ; set temperature limit for heater 1 to 280C
M308 S2 P"temp2" Y"thermistor" T100000 B4138      ; configure sensor 2 as thermistor on pin temp2
M950 H2 C"out2" T2                                ; create nozzle heater output on out2 and map it to sensor 2
M307 H2 B0 S1.00                                  ; disable bang-bang mode for heater  and set PWM limit
M143 H2 S280                                      ; set temperature limit for heater 2 to 280C
 
; Fans
M950 F0 C"out9" Q500                              ; create fan 0 on pin out9 and set its frequency
M106 P0 C"Pi" S0.8 H0 T10                         ; set fan 0 name and value. Thermostatic control is turned on
M950 F1 C"out5" Q500                              ; create fan 1 on pin out5 and set its frequency
M106 P1 C"Extruder Front" S0 H-1                  ; set fan 1 name and value. Thermostatic control is turned off
M950 F2 C"out8" Q500                              ; create fan 2 on pin out8 and set its frequency
M106 P2 C"Extruder" S1 H0 T10                     ; set fan 2 name and value. Thermostatic control is turned on
M950 F3 C"out7" Q500                              ; create fan 3 on pin out7 and set its frequency
M106 P3 C"duetfan" S0 H0 T10                      ; set fan 3 name and value. Thermostatic control is turned on
M950 F4 C"out6" Q500                              ; create fan 4 on pin out6 and set its frequency
M106 P4 C"Extruder back" S0 H-1                   ; set fan 4 name and value. Thermostatic control is turned off
 
; Tools
M563 P0 S"Right" H1 F1:4                          ; define tool 0
G10 P0 X0 Y0 Z0                                   ; set tool 0 axis offsets
G10 P0 R0 S0                                      ; set initial tool 0 active and standby temperatures to 0C
M563 P1 S"Left" H2 F1:4                           ; define tool 1
G10 P1 X-32.8 Y-0.15 Z0                           ; set tool 1 axis offsets
G10 P1 R0 S0                                      ; set initial tool 1 active and standby temperatures to 0C
 
; Custom settings
M501
 
 

[jay_s_uk]

@crowem you don't have any drivers attached to your tools in M563 so there's nothing to extrude with. You need a D value.

[crowem]

@jay_s_uk
That is strange it is set up n the config tool

[Phaedrux]

That's just the driver to axis mapping. The tools page is later on.

It produces this section

; Tools
M563 P0 S"Right" H1 F1:4                          ; define tool 0
G10 P0 X0 Y0 Z0                                   ; set tool 0 axis offsets
G10 P0 R0 S0                                      ; set initial tool 0 active and standby temperatures to 0C
M563 P1 S"Left" H2 F1:4                           ; define tool 1
G10 P1 X-32.8 Y-0.15 Z0                           ; set tool 1 axis offsets
G10 P1 R0 S0  

The M563 command needs a D# parameter. D0 is the first extruder listed, and D1 is the second.

[crowem]

@Phaedrux
Fixed it thank you. Some how the tool settings got unclicked