DuetLapse3

Proschi3D

@stuartofmt ok the pip was the problem.
thank you very much now I'm testing it.
Duetlapse is now available in the browser

stuartofmt

@Proschi78

Great !!

If you like, you can try this version. I'm about to release it but have to update the documentation first. Its fully backward compatible and uses the same options. There are a few fixes but the main difference is the UI.

All you need to do is replace the existing DuetLapse3.py file with this one (rename it first ).

~~[DuetLapse3.py]~~

Proschi3D

@stuartofmt
I tried again yesterday.
in the browser I see Duetlapse.
Duetlapse is also connected to the printer.
I see the current layer, etc. only pictures are not made

I will test the new version tonight.

Thanks

Proschi3D

@stuartofmt

Screenshot 2023-01-13 164129.png

Screenshot 2023-01-13 164154.png

Screenshot 2023-01-13 170706.png
no snapshot is taken

stuartofmt

@Proschi78
Thanks.

"Insufficient images for video to be created"

In this case zero images. So the program threw an error.
I'll see if I can clean up the logic / message in the popup.

stuartofmt

@stuartofmt

While you are testing:

-seconds 15 -dontwait will try to capture images every 15 seconds without the need to run a print job.

stuartofmt

@Proschi78 said in DuetLapse3:

@stuartofmt

I see the current layer, etc. only pictures are not made

If you see current layer > 1 and no images then the images are not being captured.

I need to see ther logfile (make sure you have -verbose set)

The logfile can be downloaded by clicking on the logfile name in the Files tab.

Proschi3D

@stuartofmt
The problem was the usb port. The snapshot works with camera2, but the picture is so dark that you can't see anything

Screenshot 2023-01-13 202714.png

stuartofmt

@Proschi78 said in DuetLapse3:

@stuartofmt
The problem was the usb port. The snapshot works with camera2, but the picture is so dark that you can't see anything

I would like to help but you need to provide details of what you are doing. At a minimum, please post the logfile with -verbose.

If you are using usb then fswebcam is being used.
If you are not getting images from the stream, then likely you have the wrong url in the commandline.

In both cases - the quality of the image is down to the settings on the program that is serving those images. DuetLapse does not manipulate the images, it only copies and shows what is there.

if fswebcam now works (before it did not) then something has changed.

What do you want to use: fswebcam (usb) or streaming ? Lets stick with one as jumping around just muddies the waters.

There are just too many combinations of software settings and cameras - some work together, some do not. This is all BEFORE DuetLapse.

Proschi3D

@stuartofmt I'll save the log today. I actually want to use the stream to take the pictures. The dark image was not made with the mjpeg streamer. It looks like he used something else. No idea why

2023-01-14 11:29:12,549 - MainThread - DUETLAPSE3 LOGFILE
2023-01-14 11:29:12,549 - MainThread - /home/pi/Duetlapse/RepetierServer/192-168-178-91/startup.log
2023-01-14 11:29:12,549 - MainThread - -------------------------------------------------------------------------------

2023-01-14 11:29:12,550 - MainThread - ################### Options at start of this print job  #####################
2023-01-14 11:29:12,550 - MainThread - # Environment
2023-01-14 11:29:12,550 - MainThread - -duet  =  192.168.178.91
2023-01-14 11:29:12,550 - MainThread - -basedir  =  /home/pi/Duetlapse
2023-01-14 11:29:12,550 - MainThread - -poll  =  12
2023-01-14 11:29:12,551 - MainThread - -instances  =  single
2023-01-14 11:29:12,551 - MainThread - -logtype  =  both
2023-01-14 11:29:12,551 - MainThread - -nolog  =  False
2023-01-14 11:29:12,551 - MainThread - -verbose  =  True
2023-01-14 11:29:12,552 - MainThread - -host  =  0.0.0.0
2023-01-14 11:29:12,552 - MainThread - -port  =  8025
2023-01-14 11:29:12,552 - MainThread - -keeplogs  =  False
2023-01-14 11:29:12,552 - MainThread - -novideo  =  False
2023-01-14 11:29:12,552 - MainThread - -deletepics  =  False
2023-01-14 11:29:12,553 - MainThread - -maxffmpeg  =  2
2023-01-14 11:29:12,553 - MainThread - -keepfiles  =  False
2023-01-14 11:29:12,553 - MainThread - # Execution
2023-01-14 11:29:12,554 - MainThread - -dontwait  =  False
2023-01-14 11:29:12,554 - MainThread - -seconds  =  0
2023-01-14 11:29:12,555 - MainThread - -detect  =  layer
2023-01-14 11:29:12,555 - MainThread - -pause  =  no
2023-01-14 11:29:12,555 - MainThread - -movehead  =  [0, 0]
2023-01-14 11:29:12,555 - MainThread - -rest  =  1
2023-01-14 11:29:12,556 - MainThread - -standby  =  False
2023-01-14 11:29:12,556 - MainThread - -restart  =  False
2023-01-14 11:29:12,556 - MainThread - # Camera
2023-01-14 11:29:12,556 - MainThread - -camera1  =  usb
2023-01-14 11:29:12,556 - MainThread - -camera2  =  stream
2023-01-14 11:29:12,556 - MainThread - -weburl1  =  http://192.168.178.70:8081/?action=stream
2023-01-14 11:29:12,557 - MainThread - -weburl2
2023-01-14 11:29:12,557 - MainThread - # Video
2023-01-14 11:29:12,557 - MainThread - -extratime  =  0
2023-01-14 11:29:12,557 - MainThread - -fps  =  10
2023-01-14 11:29:12,557 - MainThread - -minvideo  =  5
2023-01-14 11:29:12,558 - MainThread - -maxvideo  =  0
2023-01-14 11:29:12,558 - MainThread - # Overrides
2023-01-14 11:29:12,558 - MainThread - -camparam1
2023-01-14 11:29:12,559 - MainThread - -camparam2
2023-01-14 11:29:12,559 - MainThread - -vidparam1
2023-01-14 11:29:12,559 - MainThread - -vidparam2
2023-01-14 11:29:12,560 - MainThread - # UI
2023-01-14 11:29:12,560 - MainThread - -hidebuttons  =  False
2023-01-14 11:29:12,560 - MainThread - # Special Functions
2023-01-14 11:29:12,560 - MainThread - -execkey
2023-01-14 11:29:12,561 - MainThread - -----------------------------------------------------------------------


2023-01-14 11:29:12,561 - MainThread - ##########################################################
2023-01-14 11:29:12,562 - MainThread - Will start capturing images on first layer change
2023-01-14 11:29:12,562 - MainThread - ##########################################################

2023-01-14 11:29:12,562 - MainThread - ##########################################################
2023-01-14 11:29:12,562 - MainThread - Video will be created when printing ends
2023-01-14 11:29:12,563 - MainThread - or if requested from the browser interface or M117 DuetLapse3. message
2023-01-14 11:29:12,563 - MainThread - ##########################################################

2023-01-14 11:29:12,563 - MainThread - ##########################################################
2023-01-14 11:29:12,563 - MainThread - If running from a console using the command line
2023-01-14 11:29:12,564 - MainThread - Press Ctrl+C one time to stop the program and create a video.
2023-01-14 11:29:12,564 - MainThread - ##########################################################

2023-01-14 11:29:12,564 - MainThread - url: http://192.168.178.91/rr_model?key=boards post: False
2023-01-14 11:29:12,580 - MainThread - ###############################################################
2023-01-14 11:29:12,580 - MainThread - Connected to printer at 192.168.178.91
2023-01-14 11:29:12,580 - MainThread - Using Duet version 3.5beta1
2023-01-14 11:29:12,580 - MainThread - Using  API interface rr_model
2023-01-14 11:29:12,580 - MainThread - ###############################################################

2023-01-14 11:29:12,581 - MainThread - url: http://192.168.178.91/rr_gcode?gcode=M117 "" post: False
2023-01-14 11:29:12,593 - MainThread - ##########################################################
2023-01-14 11:29:12,593 - MainThread - ***** Started http listener *****
2023-01-14 11:29:12,593 - MainThread - ##########################################################

2023-01-14 11:29:12,594 - gcodeLoop - ###########################
2023-01-14 11:29:12,594 - gcodeLoop - Starting gcode Listener
2023-01-14 11:29:12,594 - gcodeLoop - ###########################

2023-01-14 11:29:12,595 - gcodeLoop - Calling function Status from gcodelistener with rr_model
2023-01-14 11:29:12,595 - MainThread - Initiating with action set to start
2023-01-14 11:29:12,595 - gcodeLoop - Getting Status
2023-01-14 11:29:12,596 - MainThread - ++++++ start state requested ++++++
2023-01-14 11:29:12,599 - MainThread - nextAction requested stopCaptureLoop
2023-01-14 11:29:12,600 - MainThread - captureLoop is not running
2023-01-14 11:29:12,600 - MainThread - nextAction satisfied waitforCaptureLoop
2023-01-14 11:29:12,601 - MainThread - ++++++ Determining next logical action ++++++
2023-01-14 11:29:12,596 - gcodeLoop - url: http://192.168.178.91/rr_model?key=state post: False
2023-01-14 11:29:12,604 - captureLoop - Starting Capture Loop
2023-01-14 11:29:12,609 - MainThread - ++++++ Entering start state ++++++
2023-01-14 11:29:12,609 - captureLoop - ****** Duet status changed to: Not yet determined *****
2023-01-14 11:29:12,609 - MainThread - nextAction exiting normally
2023-01-14 11:29:12,610 - captureLoop - ****** Print State changed to: Waiting *****
2023-01-14 11:29:16,036 - Thread-1 - !!!!! http call: {'displayStatus': ['true']} !!!!!
2023-01-14 11:29:17,625 - gcodeLoop - Calling function Status from gcodelistener with rr_model
2023-01-14 11:29:17,626 - gcodeLoop - Getting Status
2023-01-14 11:29:17,631 - gcodeLoop - url: http://192.168.178.91/rr_model?key=state post: False
2023-01-14 11:29:22,036 - Thread-2 - !!!!! http call: {'displayStatus': ['true']} !!!!!
2023-01-14 11:29:22,657 - gcodeLoop - Calling function Status from gcodelistener with rr_model
2023-01-14 11:29:22,657 - gcodeLoop - Getting Status
2023-01-14 11:29:22,660 - gcodeLoop - url: http://192.168.178.91/rr_model?key=state post: False
2023-01-14 11:29:24,622 - captureLoop - ****** Duet status changed to: processing *****
2023-01-14 11:29:24,623 - captureLoop - ****** Print State changed to: Capturing *****
2023-01-14 11:29:24,624 - captureLoop - ****** Print State changed to: Capturing *****
2023-01-14 11:29:24,624 - captureLoop - Calling function Layer from oneInterval with rr_model
2023-01-14 11:29:24,625 - captureLoop - url: http://192.168.178.91/rr_model?key=job.layer post: False
2023-01-14 11:29:24,643 - captureLoop - Calling function Status from Check for Pause with rr_model
2023-01-14 11:29:24,643 - captureLoop - Getting Status
2023-01-14 11:29:24,644 - captureLoop - url: http://192.168.178.91/rr_model?key=state post: False
2023-01-14 11:29:24,663 - captureLoop - Layer - Camera1: capturing frame 1 at layer 3 after layer change
2023-01-14 11:29:24,664 - captureLoop - Created working directory: /home/pi/Duetlapse/RepetierServer/192-168-178-91/7123_1
2023-01-14 11:29:24,666 - captureLoop - Calling function Jobname from renameworkingDir with rr_model
2023-01-14 11:29:24,667 - captureLoop - url: http://192.168.178.91/rr_model?key=job.file.fileName post: False
2023-01-14 11:29:24,684 - captureLoop - Renaming working directory: /home/pi/Duetlapse/RepetierServer/192-168-178-91/7123_1_Speed_rechts
2023-01-14 11:29:24,712 - captureLoop - Command Failure: fswebcam --quiet --no-banner /home/pi/Duetlapse/RepetierServer/192-168-178-91/7123_1_Speed_rechts/Camera1_00000001.jpeg
2023-01-14 11:29:24,712 - captureLoop - [31mError selecting input 0
[0m[31mVIDIOC_S_INPUT: Device or resource busy
[0m
2023-01-14 11:29:24,713 - captureLoop - !!!!!  There was a problem capturing an image !!!!!
2023-01-14 11:29:24,713 - captureLoop - elapsed: 12.148980379104614
2023-01-14 11:29:24,713 - captureLoop - Calling function Layer from oneInterval with rr_model
2023-01-14 11:29:24,713 - captureLoop - url: http://192.168.178.91/rr_model?key=job.layer post: False
2023-01-14 11:29:24,729 - captureLoop - Calling function Status from Check for Pause with rr_model
2023-01-14 11:29:24,729 - captureLoop - Getting Status
2023-01-14 11:29:24,730 - captureLoop - url: http://192.168.178.91/rr_model?key=state post: False
2023-01-14 11:29:24,745 - captureLoop - Layer - Camera2: capturing frame 1 at layer 3 after layer change
2023-01-14 11:29:25,015 - captureLoop - Command Exception: ffmpeg -threads 1 -loglevel quiet -y -i  -vframes 1 -threads 1/home/pi/Duetlapse/RepetierServer/192-168-178-91/7123_1_Speed_rechts/Camera2_00000001.jpeg
2023-01-14 11:29:25,015 - captureLoop - Command 'ffmpeg -threads 1 -loglevel quiet -y -i  -vframes 1 -threads 1/home/pi/Duetlapse/RepetierServer/192-168-178-91/7123_1_Speed_rechts/Camera2_00000001.jpeg' returned non-zero exit status 1.
2023-01-14 11:29:25,016 - captureLoop - !!!!!  There was a problem capturing an image !!!!!
2023-01-14 11:29:25,016 - captureLoop - elapsed: 12.45192813873291
2023-01-14 11:29:25,016 - captureLoop - Calling function Status from unPause with rr_model
2023-01-14 11:29:25,016 - captureLoop - Getting Status
2023-01-14 11:29:25,016 - captureLoop - url: http://192.168.178.91/rr_model?key=state post: False
2023-01-14 11:29:27,686 - gcodeLoop - Calling function Status from gcodelistener with rr_model
2023-01-14 11:29:27,687 - gcodeLoop - Getting Status
2023-01-14 11:29:27,690 - gcodeLoop - url: http://192.168.178.91/rr_model?key=state post: False
2023-01-14 11:29:28,038 - Thread-3 - !!!!! http call: {'displayStatus': ['true']} !!!!!
2023-01-14 11:29:32,714 - gcodeLoop - Calling function Status from gcodelistener with rr_model
2023-01-14 11:29:32,715 - gcodeLoop - Getting Status
2023-01-14 11:29:32,718 - gcodeLoop - url: http://192.168.178.91/rr_model?key=state post: False
2023-01-14 11:29:34,041 - Thread-4 - !!!!! http call: {'displayStatus': ['true']} !!!!!
2023-01-14 11:29:37,037 - captureLoop - Calling function Layer from oneInterval with rr_model
2023-01-14 11:29:37,038 - captureLoop - url: http://192.168.178.91/rr_model?key=job.layer post: False
2023-01-14 11:29:37,055 - captureLoop - elapsed: 24.49109148979187
2023-01-14 11:29:37,056 - captureLoop - Calling function Layer from oneInterval with rr_model
2023-01-14 11:29:37,056 - captureLoop - url: http://192.168.178.91/rr_model?key=job.layer post: False
2023-01-14 11:29:37,072 - captureLoop - elapsed: 24.507537603378296
2023-01-14 11:29:37,072 - captureLoop - Calling function Status from unPause with rr_model
2023-01-14 11:29:37,073 - captureLoop - Getting Status
2023-01-14 11:29:37,073 - captureLoop - url: http://192.168.178.91/rr_model?key=state post: False
2023-01-14 11:29:37,742 - gcodeLoop - Calling function Status from gcodelistener with rr_model
2023-01-14 11:29:37,743 - gcodeLoop - Getting Status
2023-01-14 11:29:37,745 - gcodeLoop - url: http://192.168.178.91/rr_model?key=state post: False
2023-01-14 11:29:40,037 - Thread-5 - !!!!! http call: {'displayStatus': ['true']} !!!!!
2023-01-14 11:29:42,771 - gcodeLoop - Calling function Status from gcodelistener with rr_model
2023-01-14 11:29:42,771 - gcodeLoop - Getting Status
2023-01-14 11:29:42,774 - gcodeLoop - url: http://192.168.178.91/rr_model?key=state post: False
2023-01-14 11:29:46,044 - Thread-6 - !!!!! http call: {'displayStatus': ['true']} !!!!!
2023-01-14 11:29:47,801 - gcodeLoop - Calling function Status from gcodelistener with rr_model
2023-01-14 11:29:47,806 - gcodeLoop - Getting Status
2023-01-14 11:29:47,807 - gcodeLoop - url: http://192.168.178.91/rr_model?key=state post: False
2023-01-14 11:29:49,103 - captureLoop - Calling function Layer from oneInterval with rr_model
2023-01-14 11:29:49,103 - captureLoop - url: http://192.168.178.91/rr_model?key=job.layer post: False
2023-01-14 11:29:49,114 - captureLoop - Calling function Status from Check for Pause with rr_model
2023-01-14 11:29:49,115 - captureLoop - Getting Status
2023-01-14 11:29:49,115 - captureLoop - url: http://192.168.178.91/rr_model?key=state post: False
2023-01-14 11:29:49,128 - captureLoop - Layer - Camera1: capturing frame 1 at layer 4 after layer change
2023-01-14 11:29:49,143 - captureLoop - Command Failure: fswebcam --quiet --no-banner /home/pi/Duetlapse/RepetierServer/192-168-178-91/7123_1_Speed_rechts/Camera1_00000001.jpeg
2023-01-14 11:29:49,143 - captureLoop - [31mError selecting input 0
[0m[31mVIDIOC_S_INPUT: Device or resource busy
[0m
2023-01-14 11:29:49,143 - captureLoop - !!!!!  There was a problem capturing an image !!!!!
2023-01-14 11:29:49,144 - captureLoop - elapsed: 36.57973766326904
2023-01-14 11:29:49,144 - captureLoop - Calling function Layer from oneInterval with rr_model
2023-01-14 11:29:49,144 - captureLoop - url: http://192.168.178.91/rr_model?key=job.layer post: False
2023-01-14 11:29:49,158 - captureLoop - Calling function Status from Check for Pause with rr_model
2023-01-14 11:29:49,159 - captureLoop - Getting Status
2023-01-14 11:29:49,159 - captureLoop - url: http://192.168.178.91/rr_model?key=state post: False
2023-01-14 11:29:49,172 - captureLoop - Layer - Camera2: capturing frame 1 at layer 4 after layer change
2023-01-14 11:29:49,429 - captureLoop - Command Exception: ffmpeg -threads 1 -loglevel quiet -y -i  -vframes 1 -threads 1/home/pi/Duetlapse/RepetierServer/192-168-178-91/7123_1_Speed_rechts/Camera2_00000001.jpeg
2023-01-14 11:29:49,430 - captureLoop - Command 'ffmpeg -threads 1 -loglevel quiet -y -i  -vframes 1 -threads 1/home/pi/Duetlapse/RepetierServer/192-168-178-91/7123_1_Speed_rechts/Camera2_00000001.jpeg' returned non-zero exit status 1.
2023-01-14 11:29:49,430 - captureLoop - !!!!!  There was a problem capturing an image !!!!!
2023-01-14 11:29:49,430 - captureLoop - elapsed: 36.866106033325195
2023-01-14 11:29:49,430 - captureLoop - Calling function Status from unPause with rr_model
2023-01-14 11:29:49,431 - captureLoop - Getting Status
2023-01-14 11:29:49,431 - captureLoop - url: http://192.168.178.91/rr_model?key=state post: False
2023-01-14 11:29:52,043 - Thread-7 - !!!!! http call: {'displayStatus': ['true']} !!!!!
2023-01-14 11:29:52,829 - gcodeLoop - Calling function Status from gcodelistener with rr_model
2023-01-14 11:29:52,829 - gcodeLoop - Getting Status
2023-01-14 11:29:52,832 - gcodeLoop - url: http://192.168.178.91/rr_model?key=state post: False
2023-01-14 11:29:57,859 - gcodeLoop - Calling function Status from gcodelistener with rr_model
2023-01-14 11:29:57,859 - gcodeLoop - Getting Status
2023-01-14 11:29:57,862 - gcodeLoop - url: http://192.168.178.91/rr_model?key=state post: False
2023-01-14 11:29:58,041 - Thread-8 - !!!!! http call: {'displayStatus': ['true']} !!!!!
2023-01-14 11:30:01,457 - captureLoop - Calling function Layer from oneInterval with rr_model
2023-01-14 11:30:01,458 - captureLoop - url: http://192.168.178.91/rr_model?key=job.layer post: False
2023-01-14 11:30:01,477 - captureLoop - elapsed: 48.913480281829834
2023-01-14 11:30:01,479 - captureLoop - Calling function Layer from oneInterval with rr_model
2023-01-14 11:30:01,479 - captureLoop - url: http://192.168.178.91/rr_model?key=job.layer post: False
2023-01-14 11:30:01,496 - captureLoop - elapsed: 48.932276010513306
2023-01-14 11:30:01,497 - captureLoop - Calling function Status from unPause with rr_model
2023-01-14 11:30:01,498 - captureLoop - Getting Status
2023-01-14 11:30:01,499 - captureLoop - url: http://192.168.178.91/rr_model?key=state post: False
2023-01-14 11:30:02,888 - gcodeLoop - Calling function Status from gcodelistener with rr_model
2023-01-14 11:30:02,888 - gcodeLoop - Getting Status
2023-01-14 11:30:02,891 - gcodeLoop - url: http://192.168.178.91/rr_model?key=state post: False
2023-01-14 11:30:04,035 - Thread-9 - !!!!! http call: {'displayStatus': ['true']} !!!!!
2023-01-14 11:30:07,918 - gcodeLoop - Calling function Status from gcodelistener with rr_model
2023-01-14 11:30:07,919 - gcodeLoop - Getting Status
2023-01-14 11:30:07,922 - gcodeLoop - url: http://192.168.178.91/rr_model?key=state post: False
2023-01-14 11:30:10,037 - Thread-10 - !!!!! http call: {'displayStatus': ['true']} !!!!!
2023-01-14 11:30:12,450 - Thread-11 - !!!!! http call: {'displayFiles': ['true']} !!!!!
2023-01-14 11:30:12,451 - Thread-11 - list_dir called with path = /home/pi/Duetlapse/RepetierServer/192-168-178-91
2023-01-14 11:30:12,451 - Thread-11 - Finished parsing the files directory
2023-01-14 11:30:12,944 - gcodeLoop - Calling function Status from gcodelistener with rr_model
2023-01-14 11:30:12,945 - gcodeLoop - Getting Status
2023-01-14 11:30:12,948 - gcodeLoop - url: http://192.168.178.91/rr_model?key=state post: False
2023-01-14 11:30:13,530 - captureLoop - Calling function Layer from oneInterval with rr_model
2023-01-14 11:30:13,530 - captureLoop - url: http://192.168.178.91/rr_model?key=job.layer post: False
2023-01-14 11:30:13,549 - captureLoop - elapsed: 60.98456144332886
2023-01-14 11:30:13,549 - captureLoop - Calling function Layer from oneInterval with rr_model
2023-01-14 11:30:13,550 - captureLoop - url: http://192.168.178.91/rr_model?key=job.layer post: False
2023-01-14 11:30:13,567 - captureLoop - elapsed: 61.002771615982056
2023-01-14 11:30:13,568 - captureLoop - Calling function Status from unPause with rr_model
2023-01-14 11:30:13,568 - captureLoop - Getting Status
2023-01-14 11:30:13,568 - captureLoop - url: http://192.168.178.91/rr_model?key=state post: False
2023-01-14 11:30:14,677 - Thread-12 - !!!!! http call: {'displayVideo': ['true']} !!!!!
2023-01-14 11:30:15,608 - Thread-13 - !!!!! http call: {'displayFiles': ['true']} !!!!!
2023-01-14 11:30:15,608 - Thread-13 - list_dir called with path = /home/pi/Duetlapse/RepetierServer/192-168-178-91
2023-01-14 11:30:15,610 - Thread-13 - Finished parsing the files directory
2023-01-14 11:30:17,972 - gcodeLoop - Calling function Status from gcodelistener with rr_model
2023-01-14 11:30:17,973 - gcodeLoop - Getting Status
2023-01-14 11:30:17,978 - gcodeLoop - url: http://192.168.178.91/rr_model?key=state post: False
2023-01-14 11:30:19,410 - Thread-14 - !!!!! http call: {'getfile': ['/home/pi/Duetlapse/RepetierServer/192-168-178-91/7123_1_Speed_rechts.log']} !!!!!
2023-01-14 11:30:19,412 - Thread-14 - Trying to get file /home/pi/Duetlapse/RepetierServer/192-168-178-91/7123_1_Speed_rechts.log
2023-01-14 11:30:19,444 - Thread-14 - application/octet-stream

Proschi3D

@stuartofmt thanks for your help, i got it working

stuartofmt

@Proschi78
Its important for other people reading these posts that they benefit from what works. That feedback is very helpful.

I can see, from the logfile that the usb camera ( -camera1 usb) was failing AND the stream camera (-camera 2 stream) was failing.

How did you get it working? Did you us the command line that I recommended ? If no - what did you use?

Proschi3D

@stuartofmt use the following for the mjpeg streamer

 python3 DuetLapse3.py -port 8025 -duet 192.168.178.91 -detect layer -weburl1 http://192.168.178.70:8081/?action=snapshot -camera1 web

How do I enable it to automatically generate a video when it ends?

pi@RepetierServer:~/Duetlapse $ 192.168.178.91 terminate - Terminating
192.168.178.91 nextAction - ++++++ Entering terminate state ++++++
192.168.178.91 terminate - captureLoop is not running
192.168.178.91 nextAction - nextAction exiting normally
192.168.178.91 terminate - Wait for video to complete
192.168.178.91 terminate - makeVideo is not running
192.168.178.91 terminate - *****  Cleaning up files for phase:  terminate  *****
192.168.178.91 terminate - ********* gcodeLoopState is 0 - Waiting to complete *********
192.168.178.91 Thread-332 - !!!!! http call: {'displayStatus': ['true']} !!!!!
192.168.178.91 terminate - !!!!! http listener stopped  !!!!!
192.168.178.91 terminate - Program Terminated
Killed
^C

stuartofmt

I am pleased to announce the release of version 5.0.0 of DuetLapse3.

Thanks to the good graces of the Duet3D team, I will soon be developing against an SBC. This release is the first step towards a plugin. The UI is completely refactored and there are some new features as well (e.g. being able to set the maximum video length).

See the first post for download links

VERSION 5.0.x
Note .x releases are issued without documentation to correct minor issues e.g. a typo or edge-case logic error.

[1] Completely revised UI
[2] Added display of last captured image to UI
[3] Added ability to specify a config file with -file option This avoids the need for long command lines. Options in command line over-write those in config file
[4] Added -maxvideo. Limits the maximum length of video by varying fps as needed
[5] Added ability to change -fps -minvideo and -maxvideo in the UI
[6] UI gives indication of video creation status
[7] Changed logfile name on startup
[8] Sequential jobs are numbered
[9] Misc bug fixes

Enjoy and as always, feedback and suggestions are welcome.

stuartofmt

@Proschi78

I have no idea. You did not use -verbose.
Instead of copy paste the log file its best to upload the logfile.

The logfile can be downloaded by clicking on the link for the logfile. The currently running logfile is the one at the top (shown highlighted in this example). Previous logfiles are below. You can use the -keepfiles option to maintain some history.

3-Latest Logfile.png

Proschi3D

ok i do it again with verbose

stuartofmt

@Proschi78 said in DuetLapse3:

ok i do it again with verbose

Version 5.0.3 has been posted to github. It has a few changes from the version I gave you access to. Mostly these are cosmetic but its best to be on this version.

stuartofmt

@osterac

Wanted to bring to your attention Verson 5.0.x.
I got side-tracked with some significant code re-arangement ( same functionality). The ability to set max video length is formally included.

Please let me know what you think.

stuartofmt

@Proschi78 said in DuetLapse3:

ok i do it again with verbose

Is everything running correctly now ?

Proschi3D

@stuartofmt I couldn't try it anymore. But the new version didn't start at all