Duet does not auto-connect to WiFi

[Bassbadger]

@gloomyandy

[Bassbadger]

@Phaedrux
Yes, it does.

M587
Remembered networks:
TNCAP2FCC19 IP=192.168.1.14 GW=0.0.0.0 NM=0.0.0.0
PLUSNET-3X9K IP=0.0.0.0 GW=0.0.0.0 NM=0.0.0.0
Office IP=0.0.0.0 GW=0.0.0.0 NM=0.0.0.0
TP-Link_1D56 IP=0.0.0.0 GW=0.0.0.0 NM=0.0.0.0
ok

[Bassbadger]

@Bassbadger said in Duet does not auto-connect to WiFi:

@Phaedrux
Yes, it does.

M587
Remembered networks:
TNCAP2FCC19 IP=192.168.1.14 GW=0.0.0.0 NM=0.0.0.0
PLUSNET-3X9K IP=0.0.0.0 GW=0.0.0.0 NM=0.0.0.0
Office IP=0.0.0.0 GW=0.0.0.0 NM=0.0.0.0
TP-Link_1D56 IP=0.0.0.0 GW=0.0.0.0 NM=0.0.0.0
ok

Ah, the correct network is TP-Link_1D56. Should the IP be 0.0.0.0?

[Phaedrux]

I suggest you send M588 S"*" to clear all saved networks and then use M587 to re-add your prefered network.

[Bassbadger]

@Phaedrux
M588 S”*”
ok
M587
Remembered networks: none
ok
M587 S”TP-Link_1D56” P”70259605”
ok
M587
Remembered networks:
TP-Link_1D56 IP=0.0.0.0 GW=0.0.0.0 NM=0.0.0.0
ok

But when I disconnect USB and switch on the PSU it does not connect.

Should there be an IP in the Remembered networks or should it be 0.0.0.0?

[Bassbadger]

@Bassbadger

[Phaedrux]

When you still have usb connected can you send M552 S1?

[Bassbadger]

@Phaedrux
Connects fine and reachable with DWC

M552 S1
ok
WiFi module started
Error: WiFi module reported: no known networks found
WiFi module is idle
WiFi module is connected to access point TP-Link_1D56, IP address 192.168.1.66

[Bassbadger]

@Bassbadger
I notice this file is the config-network.g
Is this the same as config.g as I don't seem to have one of those?

[Bassbadger]

@Bassbadger

Am I missing the config.g file and if so, where can I find it?
I'm using an Ooznest Workbee with a Duet 2 WiFi

Board: Duet 2 WiFi (2WiFi)
Firmware: RepRapFirmware for Duet 2 WiFi/Ethernet 3.4.5 (2022-11-30)
Duet WiFi Server Version: 1.27

[Phaedrux]

You have no config.g in your sys folder?

You may want to check in with Oozenest to make sure you have all the files they provide for configuration.

[Bassbadger]

@Phaedrux
Thanks. I think I mistook config-network.g for config.g
So I'm guessing config.g calls config-network.g I'll check the Ooznest site for a config.g file.

[Bassbadger]

@Phaedrux
Got it! Added the config.g file to the system and now I have Wifi connection automatically.

Thanks to all for your help.