Duet3D Logo Duet3D
    • Tags
    • Documentation
    • Order
    • Register
    • Login

    Wiring Multiple Endstops in Parallel or Series with Duet 6XD

    Scheduled Pinned Locked Moved
    Duet Hardware and wiring
    4
    33
    1.3k
    Loading More Posts
    • Oldest to Newest
    • Newest to Oldest
    • Most Votes
    Reply
    • Reply as topic
    Log in to reply
    This topic has been deleted. Only users with topic management privileges can see it.
    • developeralgo222undefined
      developeralgo222 @droftarts
      last edited by developeralgo222

      @droftarts said in Wiring Multiple Endstops in Series with Duet 6XD:

      Do you have only one motor on the Y axis? If so, you may as well wire both X axis endstops in parallel, and all four Y axis endstops in parallel, and only use two inputs.

      @droftarts , i only have 1x Nema 34 Closed Loop Motor for X-axis and 1x Nema 34 Closed Loop Motor for Y-axis. i.e Each Axis has only a single Motor.

      Updated Config.g

      ; General preferences
G90                            ; send absolute coordinates...
M83                            ; ...but relative extruder moves
M550 P"MYTEST PNP"              ; set printer name

; Wait a moment for the CAN expansion boards to start
G4 S2

; Network
if {network.interfaces[0].type = "ethernet"}
    M552 P10.0.0.200 S1			; enable network and set IP address
	M553 P255.255.255.0			; set netmask
    M554 P10.0.0.1				; set gateway
else
    M552 S1

M586 P0 S1                     ; enable HTTP
M586 P1 S0                     ; disable FTP
M586 P2 S0                     ; disable Telnet

;The X axis to control the movement of the PnP head right and left. Right(Clockwise rotation to move Forward = S0) is positive.
;The Y axis to control the movement of the PnP head forward and back. Forward( AntiClockwise rotation to move Forward = S1) is positive.
;The Z axis to control raising and lowering of the PnP nozzle up and down. Up is positive.
;The V, U, W, A, B, C (for 6-Head nozzles) axes rotates clockwise and counter-clockwise. Counter-clockwise is positive.
;RepRapFirmware supports X, Y and Z axes as standard and allows you to create up to 7 additional axes depending on the firmware 
;version and which Duet you are using. Axes are created and associated with ;stepper motors using the M584 command in config.g. 
;You may use any of the following letters to refer to the new axes: U V W A B C D (letter D is not supported in older firmware versions)

;If no T parameter is given, then on boards having internal drivers the step pulse width and interval are guaranteed to be suitable for the on-board drivers only, 
;and will generally be too fast for external drivers. On the MB6XD board the default is T2.5:2.5:2.5:2.5.

; Drives
;Physical Drives CAN ID = 0
M569 P0.0 S0 R1 T5:5:10:10           ; X-Axis physical drive 0.0 goes forwards on CAN ID = 0 - Duet 6XD Drive 0.0 with 2.5us timings between pulses
M569 P0.1 S1 R1 T5:5:10:10           ; Y-Axis physical drive 0.1 goes forwards on CAN ID = 0 - Duet 6XD Drive 0.1 with 2.5us timings between pulses
;Physical Drives CAN ID = 1
M569 P1.0 S1                ; Z & U Axis physical drive 1.0 Rotates Clockwise or Anticlockwise to move CAM driven dual nozzles down and up on Z & U axis on CAN ID = 1 - Duet 3HC Drive 1.0
M569 P1.1 S1                ; V & W Axis physical drive 1.1 Rotates Clockwise or Anticlockwise to move CAM driven dual nozzles down and up on V & W axis on CAN ID = 1 - Duet 3HC Drive 1.1
M569 P1.2 S1                ; A & B Axis physical drive 1.2 Rotates Clockwise or Anticlockwise to move CAM driven dual nozzles down and up on A & B axis on CAN ID = 1 - Duet 3HC Drive 1.2
;Physical Drives CAN ID = 2
M569 P2.0 S1                ; C-Axis physical drive 2.0 goes Rotates forwards and backwards (+180 and -180 ) on CAN ID = 2 - Duet 3HC Drive 2.0
M569 P2.1 S1                ; D-Axis physical drive 2.1 goes Rotates forwards and backwards (+180 and -180 ) on CAN ID = 2 - Duet 3HC Drive 2.1
M569 P2.2 S1                ; 'A-Axis physical drive 2.2 goes Rotates forwards and backwards (+180 and -180 ) on CAN ID = 2 - Duet 3HC Drive 2.2
;Physical Drives CAN ID = 3
M569 P3.0 S1                ; 'B-Axis physical drive 3.0 goes Rotates forwards and backwards (+180 and -180 ) on CAN ID = 3 - Duet 3HC Drive 3.0
M569 P3.1 S1                ; 'C-Axis physical drive 3.1 goes Rotates forwards and backwards (+180 and -180 ) on CAN ID = 3 - Duet 3HC Drive 3.1
M569 P3.2 S1                ; 'D-Axis physical drive 3.2 goes Rotates forwards and backwards (+180 and -180 ) on CAN ID = 3 - Duet 3HC Drive 3.2

;By default Z U V W are linear and A B C D are rotary; but you can change that using the R

; Enable All the drives 
M17  ; Enable All the drives
; set visible drive mapping
; X-Axis , Y-Axis (2 x Nema 34 Closed Loop Motors) and Z-Axes (Z,U,V,W,A,B) mapping to 3 Stepper motors 
; directly connected to 3HC (CAN ID = 1) (which moves the nozzles up and down along Z-axis)
;M584 X0.0 Y0.1 Z1.0 U1.0 V1.1 W1.1 A1.2 B1.2 R0 ;  LIN R0 = LINEAR, R1 = ROTATION
M584 X0.0 Y0.1 R0 ;  LIN R0 = LINEAR, R1 = ROTATION
; Rotational Axes mapping (C, D, 'A, 'B, 'C, 'D ) to 6 motors directly connected to 3HC (CAN ID 2 and 3) (which rotates the nozzles +180 / -180 along Rotational axis)
;M584 C2.0 D2.1 'A2.2 'B3.0 'C3.1 'D3.2 R1  ;    LIN R0 = LINEAR, R1 = ROTATION
M584 Z1.0 U1.0 V1.1 W1.1 A1.2 B1.2 C2.0 D2.1 'A2.2 'B3.0 'C3.1 'D3.2 R1  ;    LIN R0 = LINEAR, R1 = ROTATION

M350 Z16 U16 V16 W16 A16 B16 C16 D16 'A16 'B16 'C16 'D16 I1                     ; configure microstepping with interpolation. This is irrelevant for external drives (X & Y )
M92 X64.00 Y64.00 Z8.888 U8.888 V8.888 W8.888 A8.888 B8.888  C8.888 D8.888 'A8.888 'B8.888 'C8.888 'D8.888          ; set steps per mm 50mm/rev
M566 X300.0 Y300.0 Z300.0 U300.0 V300.0 W300.0 A300.0 B300.0  C100.0 D100.0 'A100.0 'B100.0 'C100.0 'D100.0         ; set maximum instantaneous speed changes (mm/min)
M203 X5000.00 Y5000.00 Z5000.00 U5000.00 V5000.00 W5000.00 A5000.00 B5000.00  C5000.00 D5000.00 'A5000.00 'B5000.00 'C5000.00 'D5000.00     ; set maximum speeds (mm/min)
M201 X1000.00 Y1000.00 Z500.00 U500.00 V500.00 W500.00 A500.00 B500.00  C1000.00 D1000.00 'A1000.00 'B1000.00 'C1000.00 'D1000.00                         ; set accelerations (mm/s^2)
M906 Z600.0 U600.0 V600.0 W600.0 A600.0 B600.0  C500.0 D500.0 'A500.0 'B500.0 'C500.0 'D500.0 I30        ; set motor currents (mA) and motor idle factor in per cent. This is irrelevant for external drives (X & Y )
M84 S30      ; Set idle timeout
M564 H0		 ; Sets homing, H0 allows mvmnt wo homing

; Axis Limits
M208 X0 Y0 Z-160 U-160 V-160 W-160 A-160 B-160  C0 D0 'A0 'B0 'C0 'D0 S1	; Set axis minima
M208 X500 Y500 Z0 U0 V0 W0 A0 B0 C180 D180 'A180 'B180 'C180 'D180 S0	    ; Set axis maxima


; Triggers -- Two triggers, one for X and one for Y, and set them to pause the machine
M950 J1 C"io1.in"  ; define input 1 pin
M950 J2 C"io2.in"  ; define input 2 pin
M581 T1 S1 P1:2 S1 R0 ; invoke trigger 1 (pause) when an inactive-to-active edge (correct for NO switches) is detected on input 1 or input 2 at any time


; There are two parameters to be set for each endstop:

; (1) The electrical type of the endstop (S parameter). S0 = active low (S0, e.g. normally-open switch or Hall sensor), S1 = active high (S1, e.g. a normally-closed switch or opto switch),
; S2 = Use Z probe (S2) and S3 = for using motor stall detection (S3).

; (2) Whether the endstop is at the minimum end (Low End) or the maximum end (High End) of the axis. 
; These are the X, Y and Z parameters. 0 = no endstop present(e.g X0) , 1 = an endstop switch at the Minimum end (e.g X1) , 2 = an endstop switch at the Maximum end (e.g X2) of the axis.

; Endstops 
; For X and Y Axis
M574 X1 S1 P"io0.in"               ; configure switch-type (e.g. microswitch) endstop for low end on X via pin io0.in
M574 Y1 S1 P"io1.in"               ; configure switch-type (e.g. microswitch) endstop for low end on Y via pin io1.in
; For Z-Axis (Z,U,V,W,A,B) - Up/down)  -- CAM Driven Dual Nozzles ( 1 Motor rotates up/down to drive 2 Nozzles )
M574 Z1 S1 P"!1.io0.in"             ; configure switch-type (e.g. microswitch) endstop for low end on Z via pin 1.io0.in
M574 U1 S1 P"!1.io1.in"             ; configure switch-type (e.g. microswitch) endstop for low end on U via pin 1.io1.in
M574 V1 S1 P"!1.io2.in"             ; configure switch-type (e.g. microswitch) endstop for low end on V via pin 1.io2.in
M574 W1 S1 P"!1.io3.in"             ; configure switch-type (e.g. microswitch) endstop for low end on W via pin 1.io3.in
M574 A1 S1 P"!1.io4.in"             ; configure switch-type (e.g. microswitch) endstop for low end on A via pin 1.io4.in
M574 B1 S1 P"!1.io5.in"             ; configure switch-type (e.g. microswitch) endstop for low end on B via pin 1.io5.in
; For Rotational Axes only (C,D,'A,'B,'C,'D) +180 / - 180 )  
M574 C1 S1 P"!2.io0.in"            ; configure switch-type (e.g. microswitch) endstop for low end on C via pin 2.io0.in
M574 D1 S1 P"!2.io1.in"            ; configure switch-type (e.g. microswitch) endstop for low end on D via pin 2.io1.in
M574 'A1 S1 P"!2.io2.in"            ; configure switch-type (e.g. microswitch) endstop for low end on 'A via pin 2.io2.in
M574 'B1 S1 P"!3.io0.in"            ; configure switch-type (e.g. microswitch) endstop for low end on 'B via pin 3.io0.in
M574 'C1 S1 P"!3.io1.in"            ; configure switch-type (e.g. microswitch) endstop for low end on 'C via pin 3.io1.in
M574 'D1 S1 P"!3.io2.in"            ; configure switch-type (e.g. microswitch) endstop for low end on 'D via pin 3.io2.in


; SMC NPN Vacuum Sensors -ZSE30A-01-N-L (Not Z-Probe)
M558 P8 C"!2.io3.in"   ; Duet 3 3HC CAN_ID 2 Port 4- Vacuum Sensor Nozzle 1
M558 P8 C"!2.io4.in"   ; Duet 3 3HC CAN_ID 2 Port 5- Vacuum Sensor Nozzle 2
M558 P8 C"!2.io5.in"   ; Duet 3 3HC CAN_ID 2 Port 6- Vacuum Sensor Nozzle 3
M558 P8 C"!3.io3.in"   ; Duet 3 3HC CAN_ID 2 Port 4- Vacuum Sensor Nozzle 4
M558 P8 C"!3.io4.in"   ; Duet 3 3HC CAN_ID 2 Port 5- Vacuum Sensor Nozzle 5
M558 P8 C"!3.io5.in"   ; Duet 3 3HC CAN_ID 2 Port 6- Vacuum Sensor Nozzle 6

; 6X LINGERA Integrated Solenoid Valves (Pump and Vacuum) 
M558 P8 C"!io2.in"   ; Duet 3 6XD CAN_ID 0 Port 3- Pump and Vacuum Solenoid Valve for Nozzle 1
M558 P8 C"!io3.in"   ; Duet 3 6XD CAN_ID 0 Port 4- Pump and Vacuum Solenoid Valve for Nozzle 2
M558 P8 C"!io4.in"   ; Duet 3 6XD CAN_ID 0 Port 5- Pump and Vacuum Solenoid Valve for Nozzle 3
M558 P8 C"!io5.in"   ; Duet 3 6XD CAN_ID 0 Port 6- Pump and Vacuum Solenoid Valve for Nozzle 4
M558 P8 C"!io6.in"   ; Duet 3 6XD CAN_ID 0 Port 7- Pump and Vacuum Solenoid Valve for Nozzle 5
M558 P8 C"!io7.in"   ; Duet 3 6XD CAN_ID 0 Port 8- Pump and Vacuum Solenoid Valve for Nozzle 6

      Updated homeall.g

      ; homeall.g

M950 J1 C"nil" ; undefine X axis limit switch triggers
M950 J2 C"nil" ; undefine Y axis limit switch triggers
 
M574 X1 S1 P"io1.in" ; define X axis endstop, minimum end
M574 Y1 S1 P"io2.in" ; define Y axis endstop, minimum end
 
;	Home X-Axis and Y-Axis second
M98 P"homex.g"
M98 P"homey.g"
 
M574 X0
M574 Y0

M950 J1 C"io1.in"
M950 J2 C"io2.in"

; Home all other axis
;	Home Z-Axes first (Z, U, V, W, A, B )
M98 P"homez.g"
M98 P"homeu.g"
M98 P"homev.g"
M98 P"homew.g"
M98 P"homea.g"
M98 P"homeb.g"
;	Home Rotational axes  (C, D, 'A, 'B, 'C, 'D ) = ( C, D, a, b, c, d)  last
M98 P"homec.g"
M98 P"homed.g"
M98 P"home'a.g"
M98 P"home'b.g"
M98 P"home'c.g"
M98 P"home'd.g"

      Updated homex.g

      ; homex.g
; called to home the X axis

; Undefine any Triggers for X and Y-axis 
M950 J1 C"nil" ; undefine X axis limit switch triggers
M950 J2 C"nil" ; undefine Y axis limit switch triggers
;Define The Triggers for X and Y-axis
M574 X1 S1 P"io1.in" ; define X axis endstop, minimum end
M574 Y1 S1 P"io2.in" ; define Y axis endstop, minimum end
 
;	Home X-Axis 
G91              ; relative positioning
G1 H1 X500 F1800    ; move quickly to X axis endstop and stop there (first pass)
G1 H1 X-15 F6000     ; go back a few mm
G1 H1 X500 F360     ; move slowly to X axis endstop once more (second pass)
G90              ; absolute positioning

; 
M574 X0
M574 Y0
; Triggers
M950 J1 C"io1.in"
M950 J2 C"io2.in"

      Updated homey.g

      ; homey.g
; called to home the Y axis

; Undefine any Triggers for X and Y-axis 
M950 J1 C"nil" ; undefine X axis limit switch triggers
M950 J2 C"nil" ; undefine Y axis limit switch triggers
;Define The Triggers for X and Y-axis
M574 X1 S1 P"io1.in" ; define X axis endstop, minimum end
M574 Y1 S1 P"io2.in" ; define Y axis endstop, minimum end
 
;	Home Y-Axis 
G91              ; relative positioning
G1 H1 Y500 F1800    ; move quickly to Y axis endstop and stop there (first pass)
G1 H1 Y-15 F6000     ; go back a few mm
G1 H1 Y500 F360     ; move slowly to Y axis endstop once more (second pass)
G90              ; absolute positioning

; 
M574 X0
M574 Y0
; Triggers
M950 J1 C"io1.in"
M950 J2 C"io2.in"

      i will now try as per @droftarts , To wire both X axis endstops in parallel, and all four Y axis endstops in parallel, and only use two inputs

      Here my Schematic for the parallel Connections for the Endstops , is this correct as per your description ?

      X-Axis Endstops parallel connections
      JABIT_X_Axis_2_Endstops_in_Parallel.png

      Y-Axis Endstops parallel connections
      JABIT_Y_Axis_4_Endstops_in_Parallel.png

      Having an issue with Panasonic Photo Sensors PM25 used as endstops(i have 2 PM25 connected in parallel for X-axis to act a single endstop and 4 x PM25U connected in parallel for Y-axis) .

      Can't seem to figure out where the main issue is located ? Should i wire all the Power inputs (Brown Wires) from Sensors to a 24V ( since required Supply Voltage is 5 - 24V +/- 10% ) and GND (Blue Wires) directly to a 24V PSU instead of 5V being supplied by Duet 6XD 5V_EXT. I tried it ealier but it didn't resolve my issue

      developeralgo222undefined 1 Reply Last reply Reply Quote 0
      • developeralgo222undefined
        developeralgo222 @developeralgo222
        last edited by developeralgo222

        @developeralgo222
        Modified config.g snapshots to :

        ; Triggers -- Two triggers, one for X and one for Y, and set them to pause the machine

M950 J1 C"!io0.in"  ; define Trigger input  pin #1 on IO_0
M950 J2 C"!io1.in"  ; define Trigger input  pin #2 on IO_1
; Trigger number 0 causes an emergency stop as if M112 had been received. Trigger number 1 causes the print to be paused as if M25 had been received. Any trigger number # greater than 1 causes 
; the macro file sys/trigger#.g to be executed. Polling for further trigger conditions is suspended until the trigger macro file has been completed
M581 T1 P1:2 S1 R0 ; invoke trigger 1 (pause) when an inactive-to-active edge (correct for NO switches) is detected on input 1 or input 2 at any time
 

; There are two parameters to be set for each endstop:

; (1) The electrical type of the endstop (S parameter). S0 = active low (S0, e.g. normally-open switch or Hall sensor), S1 = active high (S1, e.g. a normally-closed switch or opto switch),
; S2 = Use Z probe (S2) and S3 = for using motor stall detection (S3).

; (2) Whether the endstop is at the minimum end (Low End) or the maximum end (High End) of the axis. 
; These are the X, Y and Z parameters. 0 = no endstop present(e.g X0) , 1 = an endstop switch at the Minimum end (e.g X1) , 2 = an endstop switch at the Maximum end (e.g X2) of the axis.

; Endstops 
; For X and Y Axis
M574 X1 S1 P"!io0.in"               ; configure active high endstop switch for low end on X via pin io0.in  
M574 Y1 S1 P"!io1.in"               ; configure active high endstop switch for low end on Y via pin io1.in

        Then sent commands

        Able to move X-Axis: Endstop visible

        G1
G1 H2  X-5
G1 H2  X0

        Able to move Y-Axis: --- Still No Y-Axis Endstop visible on M119

        G1
G1 H2  Y5
G1 H2  Y0

        M119
Endstops - X: at min stop, Y: no endstop, Z: at min stop, U: at min stop, V: at min stop, W: at min stop, A: at min stop, B: at min stop, C: not stopped, D: not stopped, a: not stopped, b: not stopped, c: not stopped, d: not stopped, Z probe: at min stop
        droftartsundefined 1 Reply Last reply Reply Quote 0
        • droftartsundefined
          droftarts administrators @developeralgo222
          last edited by droftarts

          @developeralgo222 Maybe it would have been easier to test it with one endstop on X and one on Y, to get the homing working correctly, before wiring them all together!

          However, there is an error in your config.g. You CANNOT define both the triggers AND the endstops in your config.g. One or the other. (Edit: it looks like I didn't make this clear in my earlier explanation, sorry!) I would define the triggers. If your run your config.g by using M98 P"config.g" (does this still reboot the 6XD? I think you said it did before) you will see an error, something like Error: M574: Pin 'io[x].in' is not free, which basically says the pin is not available as it is already defined.

          Your homing macros should define the endstop pins, after the triggers have been undefined. Apart from within the macro, you won't have X and Y endstops. Which is fine, because unless you actually call a homing move, endstops are ignored and the limits set by M208 are used as soft limits. And the triggers are there to catch the axis if they have skipped steps, and end up going to the endstops.

          I think you are just changing io ports used for X and Y endstops/triggers, as it looked like you had defined the wrong ones for the endstops, ie io1 and io2 for triggers and io0 and io1 for endstops.

          Ian

          Cartesian bed-slinger with Duet 3 Mini 5+ WiFi and 1LC : RRP Fisher Delta v1 with Duet 2 Maestro : TronXY X5S with Duet 3 MB6HC and Roto toolboard

          developeralgo222undefined 1 Reply Last reply Reply Quote 0
          • developeralgo222undefined
            developeralgo222 @droftarts
            last edited by developeralgo222

            @droftarts
            i did define the wrong pins. The correct pins are

            • 0.io0.in for X-Axis, Defined as Trigger 1 Pin 1

            • 0.io1.in for Y-axis, Defined as Trigger 1 Pin 2

            I am able to move the X and Y-axis to homing points except the triggers or Endstops were not working correctly. I will update as per your advice and comment out the endstop lines for X and Y axis in the config.g and just leave Trigger 1 then test again

            Updated Config.g Snapshot
            On trigger 1 for X and Y-axis and commented out Endstops for X and Y-axis

            ; Triggers -- Two triggers, one for X and one for Y, and set them to pause the machine
 
M950 J1 C"!0.io0.in"  ; define Trigger input  pin #1 on IO_0
M950 J2 C"!0.io1.in"  ; define Trigger input  pin #2 on IO_1
M581 T1 P1:2 S1 R0 ; invoke trigger 1 (pause) when an inactive-to-active edge (correct for NO switches) is detected on input 1 or input 2 at any time
 
; Endstops 
; For X and Y Axis
;M574 X1 S1 P"!0.io0.in"               ; configure active high endstop switch for low end on X via pin io0.in  
;M574 Y1 S1 P"!0.io1.in"               ; configure active high endstop switch for low end on Y via pin io1.in

            Updated homex.g

            ; homex.g
; called to home the X axis

; Undefine any Triggers for X and Y-axis 
M950 J1 C"nil" ; undefine X axis limit switch triggers
M950 J2 C"nil" ; undefine Y axis limit switch triggers
;Define The Triggers for X and Y-axis
M574 X1 S1 P"0.io0.in" ; define X axis endstop, minimum end
M574 Y1 S1 P"0.io1.in" ; define Y axis endstop, minimum end
 
;	Home X-Axis 
G91                   ; relative positioning
G1 H2 X0              ; move X-axis Minimum Homing endstop and stop there (first pass)
G1 H2 X-1575 F1800    ; move quickly to X-axis Maximum endstop and stop there (first pass)
G1 H2 X-15 F6000      ; go back a few mm
G1 H2 X-1575 F360     ; move slowly to X-axis Maximum endstop once more (second pass)
G1 H2 X0              ; move back to X-axis Minimum Homing endstop and stop there (second pass)
G92 X0
G90                   ; absolute positioning

; 
M574 X0
M574 Y0
; Triggers
M950 J1 C"0.io0.in"
M950 J2 C"0.io1.in"

            Updated homey.g

            ; homey.g
; called to home the Y axis
;
; generated by RepRapFirmware Configuration Tool v3.3.16 on Tue Dec 05 2023 09:51:46 GMT-0500 (Eastern Standard Time)


M950 J1 C"nil" ; undefine X axis limit switch triggers
M950 J2 C"nil" ; undefine X axis limit switch triggers
 
M574 X1 S1 P"!0.io0.in" ; define X axis endstop, minimum end
M574 Y1 S1 P"!0.io1.in" ; define Y axis endstop, minimum end
 
G91                   ; relative positioning
G1 H2 Y0              ; move Y-axis Minimum Homing endstop and stop there (first pass)
G1 H2 Y2125 F1800     ; move quickly to Y-axis Maximum endstop and stop there (first pass)
G1 H2 Y15 F6000       ; go back a few mm
G1 H2 Y2125 F360      ; move slowly to Y-axis Maximum endstop once more (second pass)
G1 H2 Y0              ; move back to Y-axis Minimum Homing endstop and stop there (second pass)
G92 Y0
G90                   ; absolute positioning
 
M574 X0
M574 Y0
 
M950 J1 C"!0.io0.in"
M950 J2 C"!0.io1.in"

            @droftarts , Does this look correct to you ?

            developeralgo222undefined 1 Reply Last reply Reply Quote -1
            • developeralgo222undefined
              developeralgo222 @developeralgo222
              last edited by developeralgo222

              @developeralgo222
              @droftarts , @dc42
              On the DWC console , when i send

              M98 P"config.g"

              i get "connection Interrupted HTTP request timed out" error with connection Lost, attempting to reconnect message and it disconnects DWC completely and i have to reboot manually. It does not even reboot or reset itself. Is that a bug on the RRF Software ? It seems it completely locks out Duet 6XD and i have to manually turn off the power and then power it back on. Even M112 does not reset it . Any reason why it would do that from the config.g ?
              I am running RRF 3.4.6

              M98_disconnects.png

              Below is my current Full config.g

              ; Configuration file for Duet 3 MB 6XD (firmware version 3.3)
; executed by the firmware on start-up
;
; generated by RepRapFirmware Configuration Tool v3.3.16 on Tue Dec 05 2023 09:51:46 GMT-0500 (Eastern Standard Time)

; General preferences
G90                            ; send absolute coordinates...
M83                            ; ...but relative extruder moves
M550 P"MYTEST PNP"              ; set printer name

; Wait a moment for the CAN expansion boards to start
G4 S2

; Network
if {network.interfaces[0].type = "ethernet"}
    M552 P10.0.0.200 S1			; enable network and set IP address
	M553 P255.255.255.0			; set netmask
    M554 P10.0.0.1				; set gateway
else
    M552 S1

M586 P0 S1                     ; enable HTTP
M586 P1 S0                     ; disable FTP
M586 P2 S0                     ; disable Telnet

;The X axis to control the movement of the PnP head right and left. Right(Clockwise rotation to move Forward = S0) is positive.
;The Y axis to control the movement of the PnP head forward and back. Forward( AntiClockwise rotation to move Forward = S1) is positive.
;The Z axis to control raising and lowering of the PnP nozzle up and down. Up is positive.
;The V, U, W, A, B, C (for 6-Head nozzles) axes rotates clockwise and counter-clockwise. Counter-clockwise is positive.
;RepRapFirmware supports X, Y and Z axes as standard and allows you to create up to 7 additional axes depending on the firmware 
;version and which Duet you are using. Axes are created and associated with ;stepper motors using the M584 command in config.g. 
;You may use any of the following letters to refer to the new axes: U V W A B C D (letter D is not supported in older firmware versions)

;If no T parameter is given, then on boards having internal drivers the step pulse width and interval are guaranteed to be suitable for the on-board drivers only, 
;and will generally be too fast for external drivers. On the MB6XD board the default is T2.5:2.5:2.5:2.5.

; Drives
;Physical Drives CAN ID = 0
M569 P0.0 S1 T5:5:10:10           ; X-Axis physical drive 0.0 goes backwards on CAN ID = 0 - Duet 6XD Drive 0.0 with 2.5us timings between pulses
M569 P0.1 S0 T5:5:10:10           ; Y-Axis physical drive 0.1 goes forwards on CAN ID = 0 - Duet 6XD Drive 0.1 with 2.5us timings between pulses
;Physical Drives CAN ID = 1
M569 P1.0 S1                ; Z & U Axis physical drive 1.0 Rotates Clockwise or Anticlockwise to move CAM driven dual nozzles down and up on Z & U axis on CAN ID = 1 - Duet 3HC Drive 1.0
M569 P1.1 S1                ; V & W Axis physical drive 1.1 Rotates Clockwise or Anticlockwise to move CAM driven dual nozzles down and up on V & W axis on CAN ID = 1 - Duet 3HC Drive 1.1
M569 P1.2 S1                ; A & B Axis physical drive 1.2 Rotates Clockwise or Anticlockwise to move CAM driven dual nozzles down and up on A & B axis on CAN ID = 1 - Duet 3HC Drive 1.2
;Physical Drives CAN ID = 2
M569 P2.0 S1                ; C-Axis physical drive 2.0 goes Rotates forwards and backwards (+180 and -180 ) on CAN ID = 2 - Duet 3HC Drive 2.0
M569 P2.1 S1                ; D-Axis physical drive 2.1 goes Rotates forwards and backwards (+180 and -180 ) on CAN ID = 2 - Duet 3HC Drive 2.1
M569 P2.2 S1                ; 'A-Axis physical drive 2.2 goes Rotates forwards and backwards (+180 and -180 ) on CAN ID = 2 - Duet 3HC Drive 2.2
;Physical Drives CAN ID = 3
M569 P3.0 S1                ; 'B-Axis physical drive 3.0 goes Rotates forwards and backwards (+180 and -180 ) on CAN ID = 3 - Duet 3HC Drive 3.0
M569 P3.1 S1                ; 'C-Axis physical drive 3.1 goes Rotates forwards and backwards (+180 and -180 ) on CAN ID = 3 - Duet 3HC Drive 3.1
M569 P3.2 S1                ; 'D-Axis physical drive 3.2 goes Rotates forwards and backwards (+180 and -180 ) on CAN ID = 3 - Duet 3HC Drive 3.2

;By default Z U V W are linear and A B C D are rotary; but you can change that using the R

; Enable All the drives 
M17  ; Enable All the drives
; set visible drive mapping
; X-Axis , Y-Axis (2 x Nema 34 Closed Loop Motors) and Z-Axes (Z,U,V,W,A,B) mapping to 3 Stepper motors 
; directly connected to 3HC (CAN ID = 1) (which moves the nozzles up and down along Z-axis)
;M584 X0.0 Y0.1 Z1.0 U1.0 V1.1 W1.1 A1.2 B1.2 R0 ;  LIN R0 = LINEAR, R1 = ROTATION
M584 X0.0 Y0.1 R0 ;  LIN R0 = LINEAR, R1 = ROTATION
; Rotational Axes mapping (C, D, 'A, 'B, 'C, 'D ) to 6 motors directly connected to 3HC (CAN ID 2 and 3) (which rotates the nozzles +180 / -180 along Rotational axis)
;M584 C2.0 D2.1 'A2.2 'B3.0 'C3.1 'D3.2 R1  ;    LIN R0 = LINEAR, R1 = ROTATION
M584 Z1.0 U1.0 V1.1 W1.1 A1.2 B1.2 C2.0 D2.1 'A2.2 'B3.0 'C3.1 'D3.2 R1  ;    LIN R0 = LINEAR, R1 = ROTATION

M350 Z16 U16 V16 W16 A16 B16 C16 D16 'A16 'B16 'C16 'D16 I1                     ; configure microstepping with interpolation. This is irrelevant for external drives (X & Y )
M92 X64.00 Y64.00 Z8.888 U8.888 V8.888 W8.888 A8.888 B8.888  C8.888 D8.888 'A8.888 'B8.888 'C8.888 'D8.888          ; set steps per mm 50mm/rev
M566 X300.0 Y300.0 Z300.0 U300.0 V300.0 W300.0 A300.0 B300.0  C100.0 D100.0 'A100.0 'B100.0 'C100.0 'D100.0         ; set maximum instantaneous speed changes (mm/min)
M203 X5000.00 Y5000.00 Z5000.00 U5000.00 V5000.00 W5000.00 A5000.00 B5000.00  C5000.00 D5000.00 'A5000.00 'B5000.00 'C5000.00 'D5000.00     ; set maximum speeds (mm/min)
M201 X1000.00 Y1000.00 Z500.00 U500.00 V500.00 W500.00 A500.00 B500.00  C1000.00 D1000.00 'A1000.00 'B1000.00 'C1000.00 'D1000.00                         ; set accelerations (mm/s^2)
M906 Z600.0 U600.0 V600.0 W600.0 A600.0 B600.0  C500.0 D500.0 'A500.0 'B500.0 'C500.0 'D500.0 I30        ; set motor currents (mA) and motor idle factor in per cent. This is irrelevant for external drives (X & Y )
M84 S30      ; Set idle timeout
M564 H0		 ; Sets homing, H0 allows mvmnt wo homing

; Axis Limits
M208 X0 Y0 Z-160 U-160 V-160 W-160 A-160 B-160  C0 D0 'A0 'B0 'C0 'D0 S1	; Set axis minima
M208 X-1575 Y2125 Z0 U0 V0 W0 A0 B0 C180 D180 'A180 'B180 'C180 'D180 S0	    ; Set axis maxima


; Triggers -- Two triggers, one for X and one for Y, and set them to pause the machine

M950 J1 C"!0.io0.in"  ; define input #1 pin IO_0
M950 J2 C"!0.io1.in"  ; define input #2 pin IO_1
; Trigger number 0 causes an emergency stop as if M112 had been received. Trigger number 1 causes the print to be paused as if M25 had been received. Any trigger number # greater than 1 causes 
; the macro file sys/trigger#.g to be executed. Polling for further trigger conditions is suspended until the trigger macro file has been completed
M581 T1 P1:2 S1 R0 ; invoke trigger 1 (pause) when an inactive-to-active edge (correct for NO switches) is detected on input 1 or input 2 at any time
 

; There are two parameters to be set for each endstop:

; (1) The electrical type of the endstop (S parameter). S0 = active low (S0, e.g. normally-open switch or Hall sensor), S1 = active high (S1, e.g. a normally-closed switch or opto switch),
; S2 = Use Z probe (S2) and S3 = for using motor stall detection (S3).

; (2) Whether the endstop is at the minimum end (Low End) or the maximum end (High End) of the axis. 
; These are the X, Y and Z parameters. 0 = no endstop present(e.g X0) , 1 = an endstop switch at the Minimum end (e.g X1) , 2 = an endstop switch at the Maximum end (e.g X2) of the axis.

; Endstops 
; For X and Y Axis
;M574 X1 S1 P"!0.io0.in"               ; configure active high endstop switch for low end on X via pin io0.in  
;M574 Y1 S1 P"!0.io1.in"               ; configure active high endstop switch for low end on Y via pin io1.in
; For Z-Axis (Z,U,V,W,A,B) - Up/down)  -- CAM Driven Dual Nozzles ( 1 Motor rotates up/down to drive 2 Nozzles )
M574 Z1 S1 P"!1.io0.in"             ; configure active high endstop switch for low end on Z via pin 1.io0.in
M574 U1 S1 P"!1.io1.in"             ; configure active high endstop switch for low end on U via pin 1.io1.in
M574 V1 S1 P"!1.io2.in"             ; configure active high endstop switch for low end on V via pin 1.io2.in
M574 W1 S1 P"!1.io3.in"             ; configure active high endstop switch for low end on W via pin 1.io3.in
M574 A1 S1 P"!1.io4.in"             ; configure active high endstop switch for low end on A via pin 1.io4.in
M574 B1 S1 P"!1.io5.in"             ; configure active high endstop switch for low end on B via pin 1.io5.in
; For Rotational Axes only (C,D,'A,'B,'C,'D) +180 / - 180 )  
M574 C1 S1 P"!2.io0.in"            ; configure active high endstop switch for low end on C via pin 2.io0.in
M574 D1 S1 P"!2.io1.in"            ; configure active high endstop switch for low end on D via pin 2.io1.in
M574 'A1 S1 P"!2.io2.in"            ; configure active high endstop switch for low end on 'A via pin 2.io2.in
M574 'B1 S1 P"!3.io0.in"            ; configure active high endstop switch for low end on 'B via pin 3.io0.in
M574 'C1 S1 P"!3.io1.in"            ; configure active high endstop switch for low end on 'C via pin 3.io1.in
M574 'D1 S1 P"!3.io2.in"            ; configure active high endstop switch for low end on 'D via pin 3.io2.in


; SMC NPN Vacuum Sensors -ZSE30A-01-N-L (Not Z-Probe)
M558 P8 C"!2.io3.in"   ; Duet 3 3HC CAN_ID 2 Port 4- Vacuum Sensor Nozzle 1
M558 P8 C"!2.io4.in"   ; Duet 3 3HC CAN_ID 2 Port 5- Vacuum Sensor Nozzle 2
M558 P8 C"!2.io5.in"   ; Duet 3 3HC CAN_ID 2 Port 6- Vacuum Sensor Nozzle 3
M558 P8 C"!3.io3.in"   ; Duet 3 3HC CAN_ID 2 Port 4- Vacuum Sensor Nozzle 4
M558 P8 C"!3.io4.in"   ; Duet 3 3HC CAN_ID 2 Port 5- Vacuum Sensor Nozzle 5
M558 P8 C"!3.io5.in"   ; Duet 3 3HC CAN_ID 2 Port 6- Vacuum Sensor Nozzle 6

; (SMC) LINGERA CM85-10-A-6S Integrated Solenoid Valves (Pump and Vacuum) on the Duet 6XD
M558 P8 C"!0.io3.in"   ; Duet 3 6XD CAN_ID 0 Port 4- Pump and Vacuum Solenoid Valve for Nozzle 1
M558 P8 C"!0.io4.in"   ; Duet 3 6XD CAN_ID 0 Port 5- Pump and Vacuum Solenoid Valve for Nozzle 2
M558 P8 C"!0.io5.in"   ; Duet 3 6XD CAN_ID 0 Port 6- Pump and Vacuum Solenoid Valve for Nozzle 3
M558 P8 C"!0.io6.in"   ; Duet 3 6XD CAN_ID 0 Port 7- Pump and Vacuum Solenoid Valve for Nozzle 4
M558 P8 C"!0.io7.in"   ; Duet 3 6XD CAN_ID 0 Port 8- Pump and Vacuum Solenoid Valve for Nozzle 5
M558 P8 C"!0.io8.in"   ; Duet 3 6XD CAN_ID 0 Port 9- Pump and Vacuum Solenoid Valve for Nozzle 6



; Heaters

; Fans

; Tools

; Custom settings are not defined
              dc42undefined droftartsundefined 2 Replies Last reply Reply Quote 0
              • dc42undefined
                dc42 administrators @developeralgo222
                last edited by

                @developeralgo222 are you saying that it boots up OK and you can connect with DWC; but if you try to re-run config.g using M98, you lose the DWC connection?

                If that's the case then I think it's most likely to do with the triggers. Try commenting out the M581 line(s) in config.g.

                BTW you don't need to switch those inputs between being endstops and GpIn ports for triggers, because a trigger can monitor endstops as well as GpIn pins. See the line starting "X, Y Z or any..." at https://docs.duet3d.com/en/User_manual/Reference/Gcodes#m581-configure-external-trigger.

                Duet WiFi hardware designer and firmware engineer
                Please do not ask me for Duet support via PM or email, use the forum
                http://www.escher3d.com, https://miscsolutions.wordpress.com

                1 Reply Last reply Reply Quote 0
                • droftartsundefined
                  droftarts administrators @developeralgo222
                  last edited by droftarts

                  @developeralgo222 I think your config.g crashing predated adding the triggers, but as @dc42 says, triggers in RRF 3.01 and later can read the endstop without redefining it as a trigger (older versions can't, and need to be redefined). Sorry I didn't spot this, it's been a while since having to set up endstops as limit switches! Comment out or delete the M950 J1 and J2 lines, add the endstop M574 X1 and Y1 commands back in, and change the trigger command to M581 T1 X Y S1 R0.

                  Some other things to try:

                  You have M17 very early in config.g, before any of the axes are assigned. I suggest moving to the end, or don't have it at all. The motors will all turn on as soon as one axis is commanded to move.

                  Your X axis limits are strange, I think swap them over, or maybe it should be M208 X1575 ... S0.
                  Also, your other limits:

                  ; Axis Limits
M208 X0 Y0 Z-160 U-160 V-160 W-160 A-160 B-160  C0 D0 'A0 'B0 'C0 'D0 S1	; Set axis minima
M208 X-1575 Y2125 Z0 U0 V0 W0 A0 B0 C180 D180 'A180 'B180 'C180 'D180 S0	    ; Set axis maxima

                  I'm not even sure axis ranges should be from -[nnn] to 0, but I don't see why not. On a CNC machine, you have machine coordinates, and then work coordinates. This article looks like it covers this (and RRF supports) https://mhcc.pressbooks.pub/supportcnc/chapter/g54-g59-an-introduction/
                  It looks like OpenPNP is similar: https://github.com/openpnp/openpnp/wiki/Machine-Axes

                  The rest is mostly setting up the endstop triggers, endstops. However, you have setup all the sensors and valves with M558, which is used for defining probes! I think the sensors should be set up with M950 as inputs:

                  M950 J1 C"!2.io3.in"   ; Duet 3 3HC CAN_ID 2 Port 4- Vacuum Sensor Nozzle 1
M950 J2 C"!2.io4.in"   ; Duet 3 3HC CAN_ID 2 Port 5- Vacuum Sensor Nozzle 2
[etc]

                  with each input having a unique J[nn] parameter. Make sure the number doesn't clash with the triggers, though I expect you will replace these with endstop definitions.

                  The valves should be outputs, again set with M950, with unique P[nn] parameter:

                  M950 P1 C"!0.io3.in"   ; Duet 3 6XD CAN_ID 0 Port 4- Pump and Vacuum Solenoid Valve for Nozzle 1
M950 P2 C"!0.io4.in"   ; Duet 3 6XD CAN_ID 0 Port 5- Pump and Vacuum Solenoid Valve for Nozzle 2
[etc]

                  Please make these changes, post your updated config.g, and try sending M98 P"config.g" again.

                  Ian

                  Cartesian bed-slinger with Duet 3 Mini 5+ WiFi and 1LC : RRP Fisher Delta v1 with Duet 2 Maestro : TronXY X5S with Duet 3 MB6HC and Roto toolboard

                  developeralgo222undefined 1 Reply Last reply Reply Quote 0
                  • developeralgo222undefined
                    developeralgo222 @droftarts
                    last edited by developeralgo222

                    @droftarts
                    before i run

                    M98 P"config.g"

                    Here is the updated config.g with suggested changes

                    ; Configuration file for Duet 3 MB 6XD (firmware version 3.3)
; executed by the firmware on start-up
;
; generated by RepRapFirmware Configuration Tool v3.3.16 on Tue Dec 05 2023 09:51:46 GMT-0500 (Eastern Standard Time)

; General preferences
G90                            ; send absolute coordinates...
M83                            ; ...but relative extruder moves
M550 P"MYTEST PNP"              ; set printer name

; Wait a moment for the CAN expansion boards to start
G4 S2

; Network
if {network.interfaces[0].type = "ethernet"}
    M552 P10.0.0.200 S1			; enable network and set IP address
	M553 P255.255.255.0			; set netmask
    M554 P10.0.0.1				; set gateway
else
    M552 S1

M586 P0 S1                     ; enable HTTP
M586 P1 S0                     ; disable FTP
M586 P2 S0                     ; disable Telnet

;The X axis to control the movement of the PnP head right and left. Right(Clockwise rotation to move Forward = S0) is positive.
;The Y axis to control the movement of the PnP head forward and back. Forward( AntiClockwise rotation to move Forward = S1) is positive.
;The Z axis to control raising and lowering of the PnP nozzle up and down. Up is positive.
;The V, U, W, A, B, C (for 6-Head nozzles) axes rotates clockwise and counter-clockwise. Counter-clockwise is positive.
;RepRapFirmware supports X, Y and Z axes as standard and allows you to create up to 7 additional axes depending on the firmware 
;version and which Duet you are using. Axes are created and associated with ;stepper motors using the M584 command in config.g. 
;You may use any of the following letters to refer to the new axes: U V W A B C D (letter D is not supported in older firmware versions)

;If no T parameter is given, then on boards having internal drivers the step pulse width and interval are guaranteed to be suitable for the on-board drivers only, 
;and will generally be too fast for external drivers. On the MB6XD board the default is T2.5:2.5:2.5:2.5.

; Drives
;Physical Drives CAN ID = 0
M569 P0.0 S0 T5:5:10:10           ; X-Axis physical drive 0.0 goes backwards on CAN ID = 0 - Duet 6XD Drive 0.0 with 2.5us timings between pulses
M569 P0.1 S0 T5:5:10:10           ; Y-Axis physical drive 0.1 goes forwards on CAN ID = 0 - Duet 6XD Drive 0.1 with 2.5us timings between pulses
;Physical Drives CAN ID = 1
M569 P1.0 S1                ; Z & U Axis physical drive 1.0 Rotates Clockwise or Anticlockwise to move CAM driven dual nozzles down and up on Z & U axis on CAN ID = 1 - Duet 3HC Drive 1.0
M569 P1.1 S1                ; V & W Axis physical drive 1.1 Rotates Clockwise or Anticlockwise to move CAM driven dual nozzles down and up on V & W axis on CAN ID = 1 - Duet 3HC Drive 1.1
M569 P1.2 S1                ; A & B Axis physical drive 1.2 Rotates Clockwise or Anticlockwise to move CAM driven dual nozzles down and up on A & B axis on CAN ID = 1 - Duet 3HC Drive 1.2
;Physical Drives CAN ID = 2
M569 P2.0 S1                ; C-Axis physical drive 2.0 goes Rotates forwards and backwards (+180 and -180 ) on CAN ID = 2 - Duet 3HC Drive 2.0
M569 P2.1 S1                ; D-Axis physical drive 2.1 goes Rotates forwards and backwards (+180 and -180 ) on CAN ID = 2 - Duet 3HC Drive 2.1
M569 P2.2 S1                ; 'A-Axis physical drive 2.2 goes Rotates forwards and backwards (+180 and -180 ) on CAN ID = 2 - Duet 3HC Drive 2.2
;Physical Drives CAN ID = 3
M569 P3.0 S1                ; 'B-Axis physical drive 3.0 goes Rotates forwards and backwards (+180 and -180 ) on CAN ID = 3 - Duet 3HC Drive 3.0
M569 P3.1 S1                ; 'C-Axis physical drive 3.1 goes Rotates forwards and backwards (+180 and -180 ) on CAN ID = 3 - Duet 3HC Drive 3.1
M569 P3.2 S1                ; 'D-Axis physical drive 3.2 goes Rotates forwards and backwards (+180 and -180 ) on CAN ID = 3 - Duet 3HC Drive 3.2

;By default Z U V W are linear and A B C D are rotary; but you can change that using the R

; set visible drive mapping
; X-Axis , Y-Axis (2 x Nema 34 Closed Loop Motors) and Z-Axes (Z,U,V,W,A,B) mapping to 3 Stepper motors 
; directly connected to 3HC (CAN ID = 1) (which moves the nozzles up and down along Z-axis)
M584 X0.0 Y0.1 R0 ;  LIN R0 = LINEAR, R1 = ROTATION
; Rotational Axes mapping (C, D, 'A, 'B, 'C, 'D ) to 6 motors directly connected to 3HC (CAN ID 2 and 3) (which rotates the nozzles +180 / -180 along Rotational axis)
M584 Z1.0 U1.0 V1.1 W1.1 A1.2 B1.2 C2.0 D2.1 'A2.2 'B3.0 'C3.1 'D3.2 R1  ;    LIN R0 = LINEAR, R1 = ROTATION

M350 Z16 U16 V16 W16 A16 B16 C16 D16 'A16 'B16 'C16 'D16 I1                     ; configure microstepping with interpolation. This is irrelevant for external drives (X & Y )
M92 X64.00 Y64.00 Z8.888 U8.888 V8.888 W8.888 A8.888 B8.888  C8.888 D8.888 'A8.888 'B8.888 'C8.888 'D8.888          ; set steps per mm 50mm/rev
M566 X300.0 Y300.0 Z300.0 U300.0 V300.0 W300.0 A300.0 B300.0  C100.0 D100.0 'A100.0 'B100.0 'C100.0 'D100.0         ; set maximum instantaneous speed changes (mm/min)
M203 X5000.00 Y5000.00 Z5000.00 U5000.00 V5000.00 W5000.00 A5000.00 B5000.00  C5000.00 D5000.00 'A5000.00 'B5000.00 'C5000.00 'D5000.00     ; set maximum speeds (mm/min)
M201 X1000.00 Y1000.00 Z500.00 U500.00 V500.00 W500.00 A500.00 B500.00  C1000.00 D1000.00 'A1000.00 'B1000.00 'C1000.00 'D1000.00                         ; set accelerations (mm/s^2)
M906 Z600.0 U600.0 V600.0 W600.0 A600.0 B600.0  C500.0 D500.0 'A500.0 'B500.0 'C500.0 'D500.0 I30        ; set motor currents (mA) and motor idle factor in per cent. This is irrelevant for external drives (X & Y )
M84 S30      ; Set idle timeout
M564 H0		 ; Sets homing, H0 allows mvmnt wo homing

; Axis Limits
M208 X0 Y0 Z-160 U-160 V-160 W-160 A-160 B-160  C0 D0 'A0 'B0 'C0 'D0 S1	; Set axis minima
M208 X1575 Y2125 Z0 U0 V0 W0 A0 B0 C180 D180 'A180 'B180 'C180 'D180 S0	    ; Set axis maxima


; Triggers -- Two triggers, one for X and one for Y, and set them to pause the machine

;M950 J1 C"!0.io0.in"  ; define input #1 pin IO_0
;M950 J2 C"!0.io1.in"  ; define input #2 pin IO_1
; Trigger number 0 causes an emergency stop as if M112 had been received. Trigger number 1 causes the print to be paused as if M25 had been received. Any trigger number # greater than 1 causes 
; the macro file sys/trigger#.g to be executed. Polling for further trigger conditions is suspended until the trigger macro file has been completed
M581 T1 X Y S1 R0 ; invoke trigger 1 (pause) when an inactive-to-active edge (correct for NO switches) is detected on input 1 or input 2 at any time
 

; There are two parameters to be set for each endstop:

; (1) The electrical type of the endstop (S parameter). S0 = active low (S0, e.g. normally-open switch or Hall sensor), S1 = active high (S1, e.g. a normally-closed switch or opto switch),
; S2 = Use Z probe (S2) and S3 = for using motor stall detection (S3).

; (2) Whether the endstop is at the minimum end (Low End) or the maximum end (High End) of the axis. 
; These are the X, Y and Z parameters. 0 = no endstop present(e.g X0) , 1 = an endstop switch at the Minimum end (e.g X1) , 2 = an endstop switch at the Maximum end (e.g X2) of the axis.

; Endstops 
; For X and Y Axis
M574 X1 S1 P"!0.io0.in"               ; configure active high endstop switch for low end on X via pin io0.in  
M574 Y1 S1 P"!0.io1.in"               ; configure active high endstop switch for low end on Y via pin io1.in
; For Z-Axis (Z,U,V,W,A,B) - Up/down)  -- CAM Driven Dual Nozzles ( 1 Motor rotates up/down to drive 2 Nozzles )
M574 Z1 S1 P"!1.io0.in"             ; configure active high endstop switch for low end on Z via pin 1.io0.in
M574 U1 S1 P"!1.io1.in"             ; configure active high endstop switch for low end on U via pin 1.io1.in
M574 V1 S1 P"!1.io2.in"             ; configure active high endstop switch for low end on V via pin 1.io2.in
M574 W1 S1 P"!1.io3.in"             ; configure active high endstop switch for low end on W via pin 1.io3.in
M574 A1 S1 P"!1.io4.in"             ; configure active high endstop switch for low end on A via pin 1.io4.in
M574 B1 S1 P"!1.io5.in"             ; configure active high endstop switch for low end on B via pin 1.io5.in
; For Rotational Axes only (C,D,'A,'B,'C,'D) +180 / - 180 )  
M574 C1 S1 P"!2.io0.in"            ; configure active high endstop switch for low end on C via pin 2.io0.in
M574 D1 S1 P"!2.io1.in"            ; configure active high endstop switch for low end on D via pin 2.io1.in
M574 'A1 S1 P"!2.io2.in"            ; configure active high endstop switch for low end on 'A via pin 2.io2.in
M574 'B1 S1 P"!3.io0.in"            ; configure active high endstop switch for low end on 'B via pin 3.io0.in
M574 'C1 S1 P"!3.io1.in"            ; configure active high endstop switch for low end on 'C via pin 3.io1.in
M574 'D1 S1 P"!3.io2.in"            ; configure active high endstop switch for low end on 'D via pin 3.io2.in

; SMC NPN Vacuum Sensors -ZSE30A-01-N-L (Not Z-Probe)
M950 J1 C"!2.io3.in"   ; Duet 3 3HC CAN_ID 2 Port 4- Vacuum Sensor Nozzle 1
M950 J2 C"!2.io4.in"   ; Duet 3 3HC CAN_ID 2 Port 5- Vacuum Sensor Nozzle 2
M950 J3 C"!2.io5.in"   ; Duet 3 3HC CAN_ID 2 Port 6- Vacuum Sensor Nozzle 3
M950 J4 C"!3.io3.in"   ; Duet 3 3HC CAN_ID 2 Port 4- Vacuum Sensor Nozzle 4
M950 J5 C"!3.io4.in"   ; Duet 3 3HC CAN_ID 2 Port 5- Vacuum Sensor Nozzle 5
M950 J6 C"!3.io5.in"   ; Duet 3 3HC CAN_ID 2 Port 6- Vacuum Sensor Nozzle 6

; (SMC) LINGERA CM85-10-A-6S Integrated Solenoid Valves (Pump and Vacuum) on the Duet 6XD
M950 P1 C"!0.io3.in"   ; Duet 3 6XD CAN_ID 0 Port 4- Pump and Vacuum Solenoid Valve for Nozzle 1
M950 P2 C"!0.io4.in"   ; Duet 3 6XD CAN_ID 0 Port 5- Pump and Vacuum Solenoid Valve for Nozzle 2
M950 P3 C"!0.io5.in"   ; Duet 3 6XD CAN_ID 0 Port 6- Pump and Vacuum Solenoid Valve for Nozzle 3
M950 P4 C"!0.io6.in"   ; Duet 3 6XD CAN_ID 0 Port 7- Pump and Vacuum Solenoid Valve for Nozzle 4
M950 P5 C"!0.io7.in"   ; Duet 3 6XD CAN_ID 0 Port 8- Pump and Vacuum Solenoid Valve for Nozzle 5
M950 P6 C"!0.io8.in"   ; Duet 3 6XD CAN_ID 0 Port 9- Pump and Vacuum Solenoid Valve for Nozzle 6

; Enable All the drives 
M17  ; Enable All the drives

; Heaters

; Fans

; Tools

; Custom settings are not defined
                    droftartsundefined 1 Reply Last reply Reply Quote 0
                    • droftartsundefined
                      droftarts administrators @developeralgo222
                      last edited by

                      @developeralgo222 You haven't changed the X axis limits; it still shows X0 as the minimum, and X-1575 as the maximum. Either swap them, or remove the minus from X-1575.

                      Otherwise, looks okay.

                      Ian

                      Cartesian bed-slinger with Duet 3 Mini 5+ WiFi and 1LC : RRP Fisher Delta v1 with Duet 2 Maestro : TronXY X5S with Duet 3 MB6HC and Roto toolboard

                      developeralgo222undefined 1 Reply Last reply Reply Quote 0
                      • developeralgo222undefined
                        developeralgo222 @droftarts
                        last edited by developeralgo222

                        @droftarts
                        when i test it manually according to the right-hand cartesian coordinates . My X-Axis moves Backwards from Home(Right to Left) instead of the Normal Forward ( Left to Right ) , that's why i was using Negative infront of that otherwise it crashes the X-Axis. If you look at the Endpoints and motor placements diagram above , you will see the description

                        droftartsundefined 1 Reply Last reply Reply Quote 0
                        • droftartsundefined
                          droftarts administrators @developeralgo222
                          last edited by

                          @developeralgo222 In that case, change the direction of the motor with the S parameter in M569, eg:

                          M569 P0.0 S0 T5:5:10:10

                          Then update the M208 command, and check it goes the right direction.

                          Ian

                          Cartesian bed-slinger with Duet 3 Mini 5+ WiFi and 1LC : RRP Fisher Delta v1 with Duet 2 Maestro : TronXY X5S with Duet 3 MB6HC and Roto toolboard

                          developeralgo222undefined 1 Reply Last reply Reply Quote 0
                          • developeralgo222undefined
                            developeralgo222 @droftarts
                            last edited by

                            @droftarts said in Wiring Multiple Endstops in Parallel or Series with Duet 6XD:

                            @developeralgo222 In that case, change the direction of the motor with the S parameter in M569, eg:

                            M569 P0.0 S0 T5:5:10:10

                            Then update the M208 command, and check it goes the right direction.

                            Ian

                            yes updated config.g and that fixed X-axis negative max issue

                            droftartsundefined 2 Replies Last reply Reply Quote 0
                            • droftartsundefined
                              droftarts administrators @developeralgo222
                              last edited by

                              @developeralgo222 Okay. Does it still crash when you send M98 P"config.g"?

                              Ian

                              Cartesian bed-slinger with Duet 3 Mini 5+ WiFi and 1LC : RRP Fisher Delta v1 with Duet 2 Maestro : TronXY X5S with Duet 3 MB6HC and Roto toolboard

                              developeralgo222undefined 1 Reply Last reply Reply Quote 0
                              • droftartsundefined
                                droftarts administrators @developeralgo222
                                last edited by

                                @developeralgo222 Another snag on homing; I checked with @dc42 if the trigger is ignored on homing moves. He said:

                                No, you have to deactivate the trigger.
                                ..because after the homing move you need to move away form the endst9p to release it, to avoid triggering

                                So in your homing macros, rather than disabling the trigger pin and enabling the endstop, you need to disable the trigger itself, while homing. So now the homing macros will look like this:

                                M581 T1 P-1 ; disable trigger
 
[normal homing routine for X and Y axis in here]
 
M581 T1 X Y S1 R0 ; re enable trigger

                                Ian

                                Cartesian bed-slinger with Duet 3 Mini 5+ WiFi and 1LC : RRP Fisher Delta v1 with Duet 2 Maestro : TronXY X5S with Duet 3 MB6HC and Roto toolboard

                                1 Reply Last reply Reply Quote 0
                                • developeralgo222undefined
                                  developeralgo222 @droftarts
                                  last edited by developeralgo222

                                  @droftarts Going to test that now. i was just testing if its able to Home X and Y-axis and it seems its able . Anything i need to modify on homex.g and homey.g files in relation to config.g

                                  homex.g

                                  ; homex.g
; called to home the X axis
 
M581 T1 P-1 ; disable trigger

;	Home X-Axis 
G91                   ; relative positioning
G1 H2 X0              ; move X-axis Minimum Homing endstop and stop there (first pass)
G1 H2 X1575 F5000     ; move quickly to X-axis Maximum endstop and stop there (first pass)
G1 H2 X-1575 F5000      ; go back to X0 Minimum Homing endstop 
G1 H2 X1575 F5000     ; move quickly to X-axis Maximum endstop and stop there (second pass)
G1 H2 X-1575 F5000       ; go back quickly to X0 Minimum Homing endstop once more (second pass)
G1 H2 X0              ; Mark it as the X-axis Minimum Homing endstop and stop there (second pass)
G92 X0
G90                   ; absolute positioning

 
M581 T1 X Y S1 R0 ; re enable trigger

                                  Homey.g

                                  ; homey.g
; called to home the Y axis

M581 T1 P-1 ; disable trigger
 
;	Home Y-Axis 
G91                   ; relative positioning
G1 H2 Y0              ; move Y-axis Minimum Homing endstop and stop there (first pass)
G1 H2 Y2135 F5000      ; move quickly to Y-axis Maximum endstop and stop there (first pass)
G1 H2 Y-2135 F5000     ; go back to Y0 Minimum Homing endstop 
G1 H2 Y2135 F5000      ; move quickly to Y-axis Maximum endstop and stop there (second pass)
G1 H2 Y-2135 F5000     ; go back quickly to Y0 Minimum Homing endstop once more (second pass)
G1 H2 Y0              ; Mark it as the Y-axis Minimum Homing endstop and stop there (second pass)
G92 Y0
G90                   ; absolute positioning
 
 M581 T1 X Y S1 R0 ; re enable trigger
                                  droftartsundefined 1 Reply Last reply Reply Quote 0
                                  • droftartsundefined
                                    droftarts administrators @developeralgo222
                                    last edited by droftarts

                                    @developeralgo222 See my reply before yours. You will need to edit your homing files.

                                    Edit:
                                    Using M950 J1 and J2 in your homing files to refer to limit switches will be messing with these in config.g:

                                    ; SMC NPN Vacuum Sensors -ZSE30A-01-N-L (Not Z-Probe)
M950 J1 C"!2.io3.in"   ; Duet 3 3HC CAN_ID 2 Port 4- Vacuum Sensor Nozzle 1
M950 J2 C"!2.io4.in"   ; Duet 3 3HC CAN_ID 2 Port 5- Vacuum Sensor Nozzle 2

                                    Ian

                                    Cartesian bed-slinger with Duet 3 Mini 5+ WiFi and 1LC : RRP Fisher Delta v1 with Duet 2 Maestro : TronXY X5S with Duet 3 MB6HC and Roto toolboard

                                    developeralgo222undefined 1 Reply Last reply Reply Quote 0
                                    • developeralgo222undefined
                                      developeralgo222 @droftarts
                                      last edited by

                                      @droftarts said in Wiring Multiple Endstops in Parallel or Series with Duet 6XD:

                                      Edit:
                                      Using M950 J1 and J2 in your homing files to refer to limit switches will be messing with these in config.g:

                                      ; SMC NPN Vacuum Sensors -ZSE30A-01-N-L (Not Z-Probe)
M950 J1 C"!2.io3.in"   ; Duet 3 3HC CAN_ID 2 Port 4- Vacuum Sensor Nozzle 1
M950 J2 C"!2.io4.in"   ; Duet 3 3HC CAN_ID 2 Port 5- Vacuum Sensor Nozzle 2

                                      Ian

                                      Not sure i understand what you mean by this ?

                                      developeralgo222undefined droftartsundefined 2 Replies Last reply Reply Quote 0
                                      • developeralgo222undefined
                                        developeralgo222 @developeralgo222
                                        last edited by developeralgo222

                                        @developeralgo222

                                        i sent

                                         M98 P"config.g"

                                        command and it disconnected again same issue. I don't know what is in the config.g that makes Duet 6XD crash ?

                                        1 Reply Last reply Reply Quote 0
                                        • droftartsundefined
                                          droftarts administrators @developeralgo222
                                          last edited by

                                          @developeralgo222 never mind, you updated your homing files and have fixed it now. You can always check how pins are defined by sending, M950 J1 for example.

                                          Ian

                                          Cartesian bed-slinger with Duet 3 Mini 5+ WiFi and 1LC : RRP Fisher Delta v1 with Duet 2 Maestro : TronXY X5S with Duet 3 MB6HC and Roto toolboard

                                          developeralgo222undefined 1 Reply Last reply Reply Quote 0
                                          • developeralgo222undefined
                                            developeralgo222 @droftarts
                                            last edited by developeralgo222

                                            @droftarts ok got it

                                            Getting response timeout errors on SMC Vacuum Pressure Sensors when i try to send manually M950 Jx as below

                                            12/18/2023, 1:28:42 PM	M950 J6
Error: M950: Response timeout: CAN addr 3, req type 6037, RID=65
12/18/2023, 1:28:37 PM	M950 J5
Error: M950: Response timeout: CAN addr 3, req type 6037, RID=64
12/18/2023, 1:28:33 PM	M950 J4
Error: M950: Response timeout: CAN addr 3, req type 6037, RID=63
12/18/2023, 1:28:26 PM	M950 J3
Error: M950: Response timeout: CAN addr 2, req type 6037, RID=62
12/18/2023, 1:28:22 PM	M950 J2
Error: M950: Response timeout: CAN addr 2, req type 6037, RID=61
12/18/2023, 1:28:12 PM	M950 J1
Error: M950: Response timeout: CAN addr 2, req type 6037, RID=60

                                            But i get the following for Integrated Solenoid valve (Pump & Vacuum) when i send M950 Px which seems to be fine

                                            12/18/2023, 1:32:17 PM	M950 P6
GPIO/servo port 6 pin !io8.in frequency 500Hz
12/18/2023, 1:32:15 PM	M950 P5
GPIO/servo port 5 pin !io7.in frequency 500Hz
12/18/2023, 1:32:12 PM	M950 P4
GPIO/servo port 4 pin !io6.in frequency 500Hz
12/18/2023, 1:32:09 PM	M950 P3
GPIO/servo port 3 pin !io5.in frequency 500Hz
12/18/2023, 1:32:05 PM	M950 P2
GPIO/servo port 2 pin !io4.in frequency 500Hz
12/18/2023, 1:31:57 PM	M950 P1
GPIO/servo port 1 pin !io3.in frequency 500Hz

                                            After Updating to RRF 3.5.0.-rc.2 and rebooting i attempted to test the input pins for the SMC NPN sensors but getting an error

                                            12/18/2023, 5:34:40 PM	M950 J6
Error: M950: Board 3 does not have input handle 2180
12/18/2023, 5:34:37 PM	M950 J5
Error: M950: Board 3 does not have input handle 2140
12/18/2023, 5:34:33 PM	M950 J4
Error: M950: Board 3 does not have input handle 2100
12/18/2023, 5:34:30 PM	M950 J3
Error: M950: Board 2 does not have input handle 20c0
12/18/2023, 5:34:15 PM	M950 J2
Error: M950: Board 2 does not have input handle 2080
12/18/2023, 5:34:08 PM	M950 J1
Error: M950: Board 2 does not have input handle 2040
                                            developeralgo222undefined droftartsundefined 2 Replies Last reply Reply Quote 0
                                            • First post
                                              Last post
                                            Unless otherwise noted, all forum content is licensed under CC-BY-SA