Problem mesh bed Big delta printer

[2000thy]

Hey,

I got a really big delta printer with a Duet 6HC board, only thing I can't get working is the mesh bed level(See picture)

the probing works and also te hight map looks fine (I think).

can someone take a look at the files/pictures and help.
Thanks in advance!!!!

config file:

; Configuration file for Duet 3 MB 6HC (firmware version 3.3)
; executed by the firmware on start-up
;
; generated by RepRapFirmware Configuration Tool v3.4.1 on Sun May 05 2024 12:41:38 GMT+0200 (Central European Summer Time)

; General preferences
G90                                              ; send absolute coordinates...
M83                                              ; ...but relative extruder moves
M550 P"Svetlana"                                 ; set printer name
M665 R500 L1060 B483 H1468     ;B483                  ; Set delta radius, diagonal rod length, printable radius and homed height
M666 X0 Y0 Z0                                    ; put your endstop adjustments here, or let auto calibration find them

; Wait a moment for the CAN expansion boards to start
G4 S2

; Network
M552 P0.0.0.0 S1                                 ; enable network and acquire dynamic address via DHCP
M586 P0 S1                                       ; enable HTTP
M586 P1 S0                                       ; disable FTP
M586 P2 S0                                       ; disable Telnet

; Drives
M569 P0.0 S0                                     ; physical drive 0.0 goes backwards
M569 P0.1 S0                                     ; physical drive 0.1 goes backwards
M569 P0.2 S0                                     ; physical drive 0.2 goes backwards
M569 P20.0 S0                                     ; physical drive 0.3 goes forwards
M584 X0.0 Y0.1 Z0.2 E20.0                         ; set drive mapping
M350 X16 Y16 Z16 E16 I1                          ; configure microstepping with interpolation
M92 X80.00 Y80.00 Z80.00 E409.00                  ; set steps per mm
M566 X1200.00 Y1200.00 Z1200.00 E1200.00         ; set maximum instantaneous speed changes (mm/min)
M203 X18000.00 Y18000.00 Z18000.00 E1200.00      ; set maximum speeds (mm/min)
M201 X1000.00 Y1000.00 Z1000.00 E1000.00         ; set accelerations (mm/s^2)
M906 X2000 Y2000 Z2000 E800 I30                  ; set motor currents (mA) and motor idle factor in per cent
M84 S30                                          ; Set idle timeout

; Axis Limits
;M208 Z1500 S1                                    ; set minimum Z

; Endstops
M574 X2 S1 P"io0.in"                             ; configure switch-type (e.g. microswitch) endstop for high end on X via pin io0.in
M574 Y2 S1 P"io1.in"                             ; configure switch-type (e.g. microswitch) endstop for high end on Y via pin io1.in
M574 Z2 S1 P"io2.in"                             ; configure switch-type (e.g. microswitch) endstop for high end on Z via pin io2.in

; Z-Probe
M950 S0 C"20.io0.out"                           ; create servo pin 0 for BLTouch
M558 P9 C"20.io0.in" H10 F1000 T6000              ; set Z probe type to bltouch and the dive height + speeds
G31 P500 X36 Y24 Z4.1                             ; set Z probe trigger value, offset and trigger height
M557 R483 S200                                   ; define mesh grid

; Heaters
M308 S0 P"temp0" Y"thermistor" T100000 B4138     ; configure sensor 0 as thermistor on pin temp0
M950 H0 C"out0" T0                               ; create bed heater output on out0 and map it to sensor 0
M307 H0 R0.199 K0.344:0.000 D6.06 E1.35 S1.00 B0                                 ; enable bang-bang mode for the bed heater and set PWM limit
M140 H0                                          ; map heated bed to heater 0
M143 H0 S60                                     ; set temperature limit for heater 0 to 120C
M308 S1 P"20.temp0" Y"thermistor" T100000 B4138 ; configure sensor 1 as thermistor on pin 121.temp0
M950 H1 C"20.out0" T1                           ; create nozzle heater output on 121.out0 and map it to sensor 1
M307 H1 R1.528 K0.177:0.000 D9.18 E1.35 S1.00 B0 V23.9                                 ; disable bang-bang mode for heater  and set PWM limit
M143 H1 S300                                     ; set temperature limit for heater 1 to 300C


;RUNOUT SENSOR
M591 D0 P2 C"20.io1.in" S1                ;RUNOUT SENSOR


; Fans
M950 F0 C"20.out2" Q500                         ; create fan 0 on pin 121.out2 and set its frequency
M106 P0 S0 H1 T45                                ; set fan 0 value. Thermostatic control is turned on
M950 F1 C"20.out1" Q500                         ; create fan 1 on pin 121.out1 and set its frequency
M106 P1 S1 H-1                                   ; set fan 1 value. Thermostatic control is turned off

; Tools
M563 P0 S"hot end" D0 H1 F0                      ; define tool 0
G10 P0 X0 Y0 Z0                                  ; set tool 0 axis offsets
G10 P0 R0 S0                                     ; set initial tool 0 active and standby temperatures to 0C

; Custom settings are not defined

this is a picture of the first layer:

when I start the machine ill do a home all and then this macro to set the delta calibration and the mesh bed leveling:

G28	;homedelta
G0 X0 Y0 Z40 f10000
M557 X-380:380 Y-380:380 S200
M557 R400 S100
G30 ;set 0
G32	;delta cal
G29	;heighthmap
G0 X0 Y0 Z40 f10000

this is a example code from the picture (Just the setup part)

; G-Code generated by Simplify3D(R) Version 5.1.2
; Jun 11, 2024 at 10:22:32 PM
; Settings Summary
;   processName,Process 1
;   autoConfigureMaterial,PLA
;   autoConfigureQuality,Medium
;   targetModels,xyzCalibration_cube(2)(2)
;   profileName,Svetlana
;   profileVersion,2024-06-11 19:34:08
;   app,S3D-Software 5.1.2
;   technology,fff
;   baseProfile,
;   extruder,Extruder 1
;   toolheadNumber,0
;   nozzleDiameter,0.80000
;   extrusionMultiplier,1.00000
;   extrusionWidthMode,automatic
;   extrusionWidth,0.40000
;   useRetraction,1
;   retractDistance,1.00000
;   extraRestartDistance,0.00000
;   retractVerticalLift,0.00000
;   retractSpeed,1800.00000
;   useCoasting,0
;   coastingDistance,0.20000
;   useWiping,0
;   wipingDistance,5.00000
;   speedMaxFlowRate,900.00000
;   toolheadOffsetX,0.00000
;   toolheadOffsetY,0.00000
;   filamentDiameter,1.75000
;   filamentPricePerKilogram,25.00000
;   filamentDensity,1.25000
;   primaryExtruder,Extruder 1
;   layerHeight,0.20000
;   topSolidLayers,3
;   bottomSolidLayers,3
;   outlinePerimeters,2
;   useVaseMode,0
;   useAdaptiveLayerHeights,0
;   minAdaptiveLayerHeight,0.10000
;   maxAdaptiveLayerHeight,0.30000
;   adaptiveSmoothingLevel,5
;   horizontalOuterCompensation,0.00000
;   horizontalInnerCompensation,0.00000
;   firstLayerUnits,percentage
;   firstLayerHeightPercentage,100
;   firstLayerWidthPercentage,100
;   firstLayerSpeedPercentage,50
;   firstLayerHeightAbsolute,0.30000
;   firstLayerWidthAbsolute,0.40000
;   firstLayerSpeedAbsolute,900.00000
;   startPointStrategy,closest
;   alignStartPointsX,0.00000
;   alignStartPointsY,0.00000
;   restrictStartPoints,1
;   perimeterPrintingOrder,inside_out
;   islandPrintingOrder,closest
;   printInfillBeforePerimeters,0
;   useSkirt,1
;   skirtExtruder,Extruder 1
;   skirtLayers,1
;   skirtOffset,4.00000
;   skirtOutlines,2
;   useRaft,0
;   raftExtruder,Extruder 1
;   raftBaseLayers,2
;   raftTopLayers,3
;   raftOffset,3.00000
;   raftSeparationDistance,0.14000
;   raftSpeedUnits,percentage
;   raftSpeedPercentage,30
;   raftSpeedAbsolute,600.00000
;   usePrimePillar,0
;   primePillarExtruder,Extruder 1
;   primePillarWidth,12.00000
;   primePillarLocation,north_west
;   primePillarSpeedPercentage,100
;   primePillarInfillPercentage,100
;   autoStopPrimePillar,1
;   primePillarLayersAfterAutoStop,0
;   useOozeShield,0
;   oozeShieldExtruder,Extruder 1
;   oozeShieldOffset,2.00000
;   oozeShieldOutlines,1
;   oozeShieldSidewallShape,waterfall
;   oozeShieldSidewallAngle,30
;   oozeShieldSpeedPercentage,100
;   autoStopOozeShield,1
;   oozeShieldLayersAfterAutoStop,0
;   sparseInfillExtruder,Extruder 1
;   sparseInfillPattern,rectilinear
;   sparseInfillRotation,0
;   sparseInfillPercentage,20
;   sparseInfillExtrusionWidthPercentage,100
;   sparseInfillCombinedLayers,1
;   denseInfillLayers,0
;   denseInfillPercentage,50
;   infillOutlineOverlapPercentage,15
;   minInfillLength,5.00000
;   externalInfillPattern,rectilinear
;   externalInfillRotation,0
;   solidInfillThresholdArea,25.00000
;   solidInfillExtraExpansion,0.00000
;   useMonotonic,0
;   useDiaphragm,0
;   diaphragmSolidLayers,3
;   diaphragmSpacingLayers,20
;   topLayerExtraExpansion,1.00000
;   topLayerExtrusionModifier,100
;   overrideFanSpeedForTopLayer,0
;   topLayerFanSpeedPercentage,100
;   useIroning,0
;   ironingOutlineOffsetPercentage,50
;   ironingExtrusionWidthPercentage,25
;   ironingExtrusionModifier,15
;   ironingSpeedModifier,30
;   sparseSupportExtruder,Extruder 1
;   sparseSupportInfillPattern,aligned
;   sparseSupportInfillRotation,0
;   sparseSupportInfillPercentage,30
;   sparseSupportOutlines,0
;   sparseSupportCombinedLayers,1
;   upperDenseSupportLayers,0
;   lowerDenseSupportLayers,0
;   denseSupportExtruder,Extruder 1
;   denseSupportInfillPercentage,70
;   denseSupportExtraExpansion,0.00000
;   baseSupportLayers,0
;   supportInflationDistance,0.00000
;   supportHorizontalPartOffset,0.30000
;   supportUpperSeparationLayers,1
;   supportLowerSeparationLayers,1
;   temperatureController,Extruder 1
;   enableTemperatureController,1
;   temperatureNumber,0
;   temperatureType,extruder
;   stabilizeAtStartup,1
;   temperatureSetpoints,1|210
;   useIdleCooldown,0
;   cooldownTemperature,150
;   cooldownRequiredIdleTime,180
;   cooldownReheatTime,60
;   temperatureController,bed
;   enableTemperatureController,1
;   temperatureNumber,0
;   temperatureType,platform
;   stabilizeAtStartup,1
;   temperatureSetpoints,1|50
;   useIdleCooldown,0
;   cooldownTemperature,150
;   cooldownRequiredIdleTime,180
;   cooldownReheatTime,60
;   fan,Cooling Fan
;   fanNumber,0
;   fanType,extruder
;   blipFanToFullPower,0
;   fanSetpoints,1|0,2|100
;   increaseFanForQuickLayers,1
;   fanMaxQuickLayerTime,45.00000
;   fanMinQuickLayerTime,15.00000
;   maxQuickLayerFanSpeedPercentage,100
;   defaultPrintSpeed,1800.00000
;   outerPerimeterSpeedPercentage,60
;   innerPerimeterSpeedPercentage,80
;   topLayerSpeedPercentage,50
;   solidInfillSpeedPercentage,80
;   sparseSupportSpeedPercentage,80
;   denseSupportSpeedPercentage,70
;   travelSpeedXY,3600.00000
;   travelSpeedZ,2400.00000
;   reduceSpeedForQuickLayers,1
;   speedMaxQuickLayerTime,20.00000
;   minQuickLayerSpeedPercentage,30
;   reduceSpeedForShortPerimeters,1
;   speedMaxShortPerimeterLength,80.00000
;   minShortPerimeterSpeedPercentage,50
;   reduceSpeedForMaxFlowRate,0
;   accelXY,1000.00000
;   accelZ,150.00000
;   accelE,3000.00000
;   jerkXY,600.00000
;   jerkZ,24.00000
;   jerkE,300.00000
;   exportFileFormat,gcode
;   useStickyCommands,1
;   use5D,1
;   relativeExtrusionDistances,0
;   allowExtruderAxisZeroing,1
;   independentExtruderAxes,0
;   includeM10123,0
;   includeThumbnailImages,0
;   thumbnailImageEncoding,standard
;   thumbnailImageSizes,300|300
;   x3gMachineProfile,r2
;   overrideStepsPerMillimeter,0
;   stepsPerMillimeterX,88.57319
;   stepsPerMillimeterY,88.57319
;   stepsPerMillimeterZ,400.00000
;   stepsPerMillimeterA,96.27520
;   stepsPerMillimeterB,96.27520
;   xyzFileFormatVersion,1
;   makerBotMachineProfile,replicator_5
;   makerBotModelExtruder,mk13
;   makerBotSupportExtruder,mk14_s
;   makerBotModelMaterial,pla
;   makerBotSupportMaterial,pva
;   globalOffsetX,0.00000
;   globalOffsetY,0.00000
;   globalOffsetZ,0.00000
;   applyToolheadOffsets,0
;   buildVolumeShape,cylindrical
;   buildVolumeX,200.00000
;   buildVolumeY,200.00000
;   buildVolumeZ,1300.00000
;   buildVolumeDiameter,1000.00000
;   originOffsetX,500.00000
;   originOffsetY,500.00000
;   originOffsetZ,0.00000
;   homingDirectionX,center
;   homingDirectionY,center
;   homingDirectionZ,max
;   mirrorVisualX,0
;   mirrorVisualY,1
;   mirrorVisualZ,0
;   machineBackgroundModel,
;   startingScript,G0 x0 y0 Z40 F6000|G30|
;   preLayerChangeScript,
;   postLayerChangeScript,
;   preRetractionScript,
;   postRetractionScript,
;   preToolChangeScript,
;   postToolChangeScript,
;   processChangeScript,
;   endingScript,M104 S0 ; turn off extruder|M84 ; disable motors
;   postProcessingScript,
;   useBridging,1
;   bridgingThresholdArea,50.00000
;   bridgingInfillExtraExpansion,0.00000
;   bridgingExtrusionModifier,100
;   bridgingSpeedModifier,100
;   overrideFanSpeedForBridging,0
;   bridgingFanSpeedPercentage,100
;   useFixedBridgingAngle,0
;   fixedBridgingAngle,0
;   applyBridgingToPerimeters,0
;   bridgingPerimeterExtraOverlap,0.00000
;   minBridgingPerimeterLength,10.00000
;   useToolChangeRetraction,1
;   toolChangeRetractDistance,12.00000
;   toolChangeExtraRestartDistance,-0.50000
;   toolChangeRetractSpeed,600.00000
;   toolChangePrimeOnFirstUse,0
;   toolChangeRetractAtEnd,0
;   externalThinWallType,perimeters_only
;   internalThinWallType,gap_fill
;   thinWallAllowedOverlapPercentage,10
;   singleExtrusionMinLength,1.00000
;   singleExtrusionMinWidthPercentage,50
;   singleExtrusionMaxWidthPercentage,200
;   singleExtrusionEndpointExtensionDistance,0.20000
;   onlyRetractWhenCrossingOutlines,1
;   retractBetweenLayers,1
;   retractOnTopLayers,0
;   useRetractionMinTravel,0
;   retractionMinTravel,5.00000
;   useRetractionMinExtrusion,0
;   retractionMinExtrusion,3.00000
;   onlyVerticalLiftOnTopLayers,0
;   retractWhileWiping,0
;   wipingMode,outer_perimeter
;   avoidCrossingOutlines,0
;   maxMovementDetourFactor,3.00000
;   openLoopSlicingBehavior,heal
;   openLoopThickenWidth,0.50000
;   slicingRegionRepairMode,positive
G90
M82
M106 S0 P0
M140 S50
M190 S50
M104 S210 T0
M109 S210 T0
G0 x0 y0 Z40 F6000
G30
; process Process 1
; layer 1, Z = 0.2000
T0
G92 E0.00000
G1 E-1.00000 F1800
; feature skirt
; tool H0.2000 W0.960
G1 Z0.2000 F2400
G1 X201.778 Y200.186 F3600
G92 E0.00000
G1 E1.00000 F1800
G92 E0.00000
G1 X-202.729 Y200.186 E32.28947 F900
G1 X-205.915 Y196.999 E32.64921
G1 X-205.915 Y-207.507 E64.93868
G1 X-202.729 Y-210.694 E65.29842

thank you in advance!!

[droftarts]

@2000thy You already have a thread discussing this issue, and indeed the same post as this. Please use that thread to keep all information together: https://forum.duet3d.com/topic/35738/problem-mesh-bed-delta-printer
I have locked this thread.

Ian